Related Manuals for rollease acmeda Automate Internal Sun Sensor
Summary of Contents for rollease acmeda Automate Internal Sun Sensor
- Page 1 AUTOMATE Interior Sun Sensor 433 MHz Internal sun sensor for automatic shade control. FEATURES: • 3 Modes of operation: - Close Mode - Open / Close Mode - Shade Detect Mode • 4 Light sensitivity levels • Low battery warning...
-
Page 2: Table Of Contents
4.6 Low battery notification 4.7 UP button PROGRAMMING 5.1 Protocol selection ADDING OR REMOVING SENSOR & CREATING GROUP CONTROL 6.1 Using Motor P1 Button 6.2 Using a pre-existing Controller TROUBLESHOOTING NOTES 2 | Automate Programming Instructions | Tubular Li-ion Motors ROLLEASE ACMEDA... -
Page 3: Technical Data / Pack Contents
Light Intensity Level Range: 15 - 75 Klux Transmission Distance: up to 200 meters (open space) PACK CONTENTS 1 x Sun Sensor 1 x Instruction Manual 1 x 3V - CR2032 Battery ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 3... -
Page 4: Safety
Keep clear when in operation. • Replace battery with correctly specified type. Rollease Acmeda declares this equipment is in compliance with the essential requirements and other relevant provisions of R&TT EC Directive 1999/5/EC Statement Regarding FCC Compliance This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Page 5: Installation
2. On the back of the sensor, peel clear plastic off to reveal adhesive. 3. Find desired position on glass for the sensor and press adhesive side to glass. ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 5... -
Page 6: Functional Overview
Blind stays down Light < pre-set for >15 mins Blind goes up until sensor is uncovered Blind goes back up Light < pre-set for > 15 mins Blind goes back up 6 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA... -
Page 7: View And Change Sensor Mode
When the battery needs changing, the currently selected light level LED will blink every 2 minutes UP button The up button can be used to manually overide the sensor and tell the shade to go up. ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 7... -
Page 8: Programming
Acmeda “EL” Protocol: The current LED will blink slowly 4 times to indicate that the old protocol is currently set. ARC Protocol: The current LED will blink fast 8 times to indicate that the new (ARC) protocol is currently set. 8 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA... -
Page 9: Adding Or Removing Sensor & Creating Group Control
Press P2 on existing Press P2 on existing Press P2 on new sensor. controller. controller. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor. ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 9... -
Page 10: Troubleshooting
Move sensor to a closer position motor Check power supply to motor is Power failure connected and active Check wiring is connected correctly Incorrect wiring (refer to motor installation instructions) 10 | Automate Programming Instructions | Interior Sun Sensor ROLLEASE ACMEDA... -
Page 11: Notes
NOTES ROLLEASE ACMEDA Automate Programming Instructions | Interior Sun Sensor | 11... - Page 12 ROLLEASE ACMEDA AUSTRALIA Queensland Branch Western Australia Branch 110 Northcorp Boulevard, Unit 2/62 Borthwick Avenue, Unit 1, 41 Mulgul Road, Broadmeadows VIC 3047 Murarrie QLD 4172 Malaga WA 6090 T +61 8 9248 5571 | F +61 8 9248 5572...
Need help?
Do you have a question about the Automate Internal Sun Sensor and is the answer not in the manual?
Questions and answers