Related Manuals for Photogenic PowerLight series
Summary of Contents for Photogenic PowerLight series
- Page 1 Digital, Radio-Sync OWER IGHT Operator’s Manual PowerLight PLR300DR PowerLight PLR1250DR PowerLight PLR2500DR PowerLight PLRX1250DR PowerLight PLRX2500DR & Remote Control Accessories...
- Page 2 Side display & IR receiver. PLIRC-1 Hand held remote control. Thank you for selecting the Photogenic Professional PowerLight Digital, Radio-Sync series. The PL2 series incorporates the newest electronic components providing improved lighting control, power setting repeatability and expanded functions. These products are built for the...
-
Page 3: Safety Precautions
Do not operate the unit with a damaged or broken flashtube or modeling lamp. Do not use flashtubes with broken, cracked or missing glass envelopes. To prevent damage always use Photogenic specified replacements for the flashtubes and modeling lamps. Perform no internal service work on this unit. Refer all such service to a qualified service person or return to the factory. - Page 4 The unit is shipped with the modeling lamp and flashtube not installed. While installing the modeling lamp and flashtube (with glove or clean cloth to protect the hand) be sure they are properly inserted and tight to avoid arcing and failure of the socket contacts during operation.
-
Page 5: Power Input
CONTROL PANEL AND BASIC OPERATION: Power Input: The power required to operate the PowerLight PLR300DR, PLR1250DR or PLR2500DR is 105 to 125 volts AC, 60 Hz, 10 Amp. The power cord has a 125V, 10 Amp. rating. The PowerLight Export models (PLRX1250DR and PLRX2500DR) are rated 230 volts AC, 50 Hz, 10 Amp and have a 230V power cord with a German/European plug. -
Page 6: Test Function
Flash Power: When the power is turned on the red ws LED is illuminated. You adjust the PowerLight Flash power settings by pressing the 1/2 or 1/10 f-stops UP/DOWN arrow buttons. The watt second settings will be displayed. (If the adjust button is pressed again the modeling circuit and yellow LED will be turned on.) Ready Light: The PLR300DR, PLR500DR (PLRX500DR) and PLR2500DR (PLRX2500DR) -
Page 7: Synchronization And Triggering
If the shutter appears not to be synchronized, a reputable camera repair shop should check the shutter contacts. The sync polarity is Positive on center pin of cable connectors (Photogenic part PLTC, and defined in ISO 518.) Sync voltage is 12 vdc (Spec. -
Page 8: Operational Parameters
OPERATIONAL PARAMETERS PowerLight Radio-Sync PLR500DR & PLRX1250DR Flashing Rate: The unit recharges quickly, as indicated by the READY light on the control panel. A quick series of flashes can be obtained within the limits of the recharge time. Continuous rapid flashing, however, can overheat and damage the flashtube and internal parts. The maximum recommended rate of flashing would depend upon the power level being used and the amount of operation time. -
Page 9: Specifications
Dimensions PLR300/1250DR (case)..4.5” x 4.5” x 6.75” Dimensions PLXR1250DR (case)..4.5” x 4.5” x 8.75” Flashtubes and Modeling Lamps: Flashtube ..........Plug-in style, use only Photogenic’s Standard C4-15 or C4-15C, C4-15D or C4-15F. Modeling Lamp ........250-Watt Quartz Halogen, ESS. 150-Watt Quartz Halogen, ESP. -
Page 10: Operating Time
OPERATIONAL PARAMETERS PLR2500DR & PLRX2500DR Flashing Rate: The unit recharges quickly, as indicated by the READY light on the control panel. A quick series of flashes can be obtained within the limits of the recharge time. Continuous rapid flashing, however, can overheat and damage the flashtube and internal parts. The maximum recommended rate of flashing would depend upon the power level being used and the amount of operation time. - Page 11 Dimensions PLR2500DR (case)...4.5” x 4.5” x 8.75” Dimensions PLXR2500DR (case)..4.5” x 4.5” x 10.75” Flashtubes and Modeling Lamps: Flashtube ..........Plug-in style, use only Photogenic’s Standard C4-19 or C4-19C, C4-19D or C4-19F. Modeling Lamp ........250-Watt Quartz Halogen, ESS. 150-Watt Quartz Halogen, ESP.
- Page 12 # means some number 1 to 9. Next, release the 1/2 f-stop UP arrow button. Change the UNIT number using the 1/10 UP/DOWN arrow buttons. Close the assignment feature and save the UNIT number by pressing the 1/2 UP arrow button. Advanced PowerLight series Accessories. Infrared Transmitter...
- Page 13 PLDIR-2 PLDIR-2 Remote digital display and Infrared receiver. (Must be used with PLIRC controller) The PLDIR-2 is a digital display to enhance visibility and to receive infrared signals to control the functions of the PowerLights. It displays Flash power, Modeling lamp power and unit number.
- Page 14 PLCPTR-2 Studio Controller & Software for IBM compatibles. (Must be used with PLDIR-2 receivers.) Along with infrared transmitter hardware and an IBM compatible computer, (using Windows 95, 98, 2000 or XP), the software is used by the photographer to specify the PowerLight settings for up to nine units with independent settings and save a studio setting or pose file.
- Page 15 AG47 3” & 5” snoot kit with diffuser and mounting frame. Snoots also available separately. AG47-GS Fine & coarse grids with diffuser and mounting frame. Grids also available separately PL06-CW Counter weight for PowerLights. Used with soft boxes, umbrellas and large reflectors.
-
Page 16: General Troubleshooting
General Trouble Shooting COMMON PROBLEMS AND CAUSES Unit does not charge. Probable causes: Fuse blown. (Unplug and discharge the unit-Replace fuse.) No line power to unit. (Check line cord and outlet.) Unit is on, but will not charge. (Safety thermal detector activated by heavy use, beyond specified Flashing Rates on page 9.) Unit completely off, but is connected to power and is turned on. - Page 17 Built-in receiver...wrong PowerLight model or defective. SERVICE The photographer should not attempt to make repairs. Consult a dealer for an authorized Photogenic Professional Lighting service agent. This will provide you safety, insure proper operational functions and provide continuation of your warranty.
-
Page 18: Warranty
Limited PowerLight Warranty Photogenic Professional Lighting warranties the “standard line” products are free from defects in material and workmanship of the PL2 series of PowerLights for a period of two years from date of purchase. At our choice, we will repair or replace any PL2, Solair or Voltage Smart series light that is deemed to be defective. - Page 19 Photogenic Professional Lighting 1268 Humbracht Circle, Bartlett, Illinois 60103 www.Photogenicpro.com Telephone: 630-830-2500 Fax: 630-830-2525 MANUAL PART NO. 016579-00V0 6-05...
Need help?
Do you have a question about the PowerLight series and is the answer not in the manual?
Questions and answers