CTC Union FMUX03 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. CTC Union Manuals
  4. Multiplexer
  5. FMUX03
  6. Operating instructions manual
CTC Union FMUX03 Operating Instructions Manual

CTC Union FMUX03 Operating Instructions Manual

Fiber optical multiplexer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for CTC Union FMUX03

Summary of Contents for CTC Union FMUX03

  • Page 2: Table Of Contents

    FMUX03 Table of content Chapter 1 Introduction.……………………………………………………… 1-1 Functional Description.…………….………………………… 1-2 Applications of FMUX03…………………..………………… 1-3 FMUX03 Technical Specification………………..…………… 1-4 FMUX03 Ordering Information….…………………………… Chapter 2 Installation…...…………………………………………………… 2-1 Description..…………..……………………………………… 2-2 Unpacking.…………………………………………………… 2-3 Site Requirements………………..…………………………… 2-4 Site Selection…………………………………………………. 2-5 DC or AC Electrical Outlet Connection……………..………..

  • Page 3: Chapter 1 Introduction

    The FMUX03 provides the telecommunication company a multipurpose and easy to use high quality fiber optics multiplexer. The use of FMUX03 with the Smart Agent network interface for ease of network connectivity. Provides both 10/100 Base-T and PPP interface to connect SNMP Network Management center interface system.

  • Page 4: Applications Of Fmux03

    FMUX03 1-2 Applications of FMUX03 FMUX03 is mainly used to extend the transmission distance of E1 signal by multiplexing four individual E1 channels into a single optical data stream. As illustrated below, there are three main applications for the use of FMUX03: Application 1: FMUX03 integrates 4/8/16 E1 channels into a single optical data stream.

  • Page 5: Fmux03 Technical Specification

    Jitter generation: The jitter of the E1 output signal in the absence of input jitter shall not exceed the following limits in both bands simultaneously. Jitter output should meet the requirement after FMUX03 performs the loopback test without jitter for E1 input signal. Connector Type: DB-25 female connector...
  • Page 6 FMUX03 Optical Link Wavelength: 850，1310 or 1550 nm MLM Laser diode Number of Optical Link：2 (working and protection link) Output Power: > -12dBm at 62.5/125 (850 nm Laser) ＞-12dBm at 9/125 (1310 nm Laser) ＞-12dBm at 9/125(1550 nm Laser) Receiver Sensitivity: ＞...
  • Page 7 Bits per second (baud): 9600bps Parity: None Data Bits: 8 bits Stop Bit: 1 (VT-100 or Emulation Terminal) Power DC: -36V ~ -72V AC: 90V ~ 288V(47Hz ~ 63Hz) Physical Specifications FMUX03 Dimensions Depth Width Height FMUX03/4 220mm 285mm 44.5mm FMUX03/8/16...

  • Page 8: Fmux03 Ordering Information

    FMUX03 1-4 FMUX03 Ordering Information Options for Ordering Information Optional Feature S: Surge Protection Power Module AC1: Single 90 ~ 288 VAC power supply AC2: Dual 90 ~ 288 VAC power supply DC1: Single -34 ~ -72 VDC power supply...

  • Page 9: Chapter 2 Installation

    2-2 Unpacking If there is a possibility for future relocation of the FMUX03 unit, please save the cartons and protection packaging material. The following items are shipped with your FMUX03: One FMUX03 User’s Manual...

  • Page 10: Site Selection

    36 inches (90 cm) clearance in front and at least 4 inches (10.2 cm) at the rear. To avoid overheating, leave at least 1 inch (2.5 cm) on either side of FMUX03. Also, do not stack another equipment on top of FMUX03.

  • Page 11: Chapter 3 Operating Instructions

    (4) Order Wire: User can connect FMUX03 to a headset and microphone for ease to remote configuration and testing. Each of the LED indicators is described below in detail:...

  • Page 12: Front Panel Control And Led Indicator Functions

    FMUX03 3-2 Front Panel Control and LED Indicator Functions （refrence appendix） Control or LED Indicator Function OLOS1 Red light when there is a loss of input signal OLOS2 Orange light when there is a loss of output signal LSR1(OLB) Yellow light signals an alarm in Laser sending out energy...
  • Page 13 III. Terminal Connector: LAN/PPP connector to remote terminal using RJ45. IV. Power Switches: On/Off switch for FMUX03 V. There are 5 different power supply combinations with the DC/AC dual module power supple: AC only. DC only, dual AC, dual DC, both AC and DC...

  • Page 14: Menu Tree

    FMUX03 Menu Tree...
  • Page 15 FMUX03...

  • Page 16: Chapter 4 Operating And Setup Instructions

    Modify Password: To prevent unauthorized login, user must enter a set of password to login to the system. The password for FMUX03 is a combination of the buttons below, from left to right: Up ↑ Right → Up ↑...

  • Page 17: E1 Configuration

    Under normal operation, LCD display shows that the working O/E module as “Working” and the backup O/E Module as ”Standby.” If FMUX03 detects a Loss of Signal, the LOS light will be lit and the LCD display will show that there is a Loss of Signal.

  • Page 18: Connect And Setup The Craft Port

    FMUX03 4-6 How to connect and setup the craft port Connect the craft port to a remote terminal using DB-9 cable. VT100 terminal settings: Bit Rate: 9600bps Data Bit: 8 bit Parity: No Parity Stop Bit: 1 Stop bit Set the emulation mode to”VT100” or “Auto Detect”.
  • Page 19 To go back to the previous menu, press the ‘Backspace” key. Refer to the Menu Tree for navigation. After entering the remote terminal screen, user can select Local Side operation and Remote Side operation for configuration, loopback, and monitoring of the FMUX03. Local/Remote...
  • Page 20 FMUX03 After entering the main menu, select of the nine functions: Profile E1 Configuration E1 Status Report Alarm Report Optical Configuration PM Status Report PM Threshold Setting Agent Network Configuration System Information Main （1）－1 設定值...
  • Page 21 FMUX03 E1 Configuraton...
  • Page 22 FMUX03...
  • Page 23 FMUX03...
  • Page 24 FMUX03 E1 Status...
  • Page 25 FMUX03...
  • Page 26 FMUX03...
  • Page 27 FMUX03 Alarm report Optical configuration...
  • Page 28 FMUX03 PM report...
  • Page 29 FMUX03...
  • Page 30 FMUX03...
  • Page 31 FMUX03 PM history report...
  • Page 32 FMUX03...
  • Page 33 FMUX03...
  • Page 34 FMUX03 PM Daily Report...
  • Page 35 FMUX03...
  • Page 36 FMUX03...
  • Page 37 FMUX03 Reset PM...
  • Page 38 FMUX03 PM threshold setting...
  • Page 39 FMUX03 Optical PM threshold setting...
  • Page 40 FMUX03 Agent network configuration...
  • Page 41 FMUX03...
  • Page 42 FMUX03 System information...

  • Page 43: Chapter 5 Diagnostics And Loopback Functions

    Chapter 5 - Diagnostics and Loopback Functions 5-1 General Information This chapter contains detailed information on the diagnostics and the loopback tests of the FMUX03 fiber optics transmission equipment. User can activate the loopback function to diagnose the full service. 5-2 Loopback Functions for E1 Tributary There are two types of loopback functions for the E1 Module: Local Loopback and Remote Loopback.
  • Page 44 FMUX03 3.Optical Local Loopback Local side Local side Local side Remote side Remote side Remote side All AIS All AIS 4.Optical Remote Loopback Local side Remote side Remote side Remote side All AIS Remote side: 1. E1 Local Loopback Local side...
  • Page 45 FMUX03 4. Optical Local Loopback Local side Local side Local side Remote side Remote side Remote side All AIS All AIS...
  • Page 46 FMUX03 Weighting (dB) Slope : 20 dB/Decade 20Hz---------- Band 1 -----------100KHz 18kHz---------- Band 2 -----------100KHz Frequency ( Log Scale ) Fig 1.Frequency characteristic weighting function for E1 jitter specification Acceptable Range Sinusoidal Input Jitter Amplitude (PK-PK UI) Jitter Frequency Digital...
  • Page 47 FMUX03 0.5dB Acceptable Range -19.5dB 10 Hz 40 Hz 400 Hz Fig 3. E1 Desynchronize Jitter Transfer 269 ns (244 + 25) V = 100% 194 ns (244 ? 50) Nominal pulse 244 ns 219 ns (244 ? 25) 488 ns...

  • Page 48: Appendix A-1. Db25 Pin Assignment For Tributary E1 Line Connection

    CTC Union FMUX03 APPENDIX A-1 DB25 Pin Assignment for Tributary E1 Line Connection GNDF TX_R2 Ch2 Tx pair TX_T2 RX_R2 Ch2 Rx pair RX_T2 RX_R1 Ch1 Rx pair RX_T1 TX_R1 Ch1 Tx pair TX_T1 GNDF TX_R4 Ch4 Tx pair TX_T4...
  • Page 49 CTC Union FMUX03 A-3 Alarm Alarm Status LED sign Single OE OLOSW OLOS1 OLOSP OLOS2 Dual OE OLOSW OLOS1 OLOSP OLOS2 OLOSW & OLOSP OLOS1, OLOS2 Dual PWRF1 Power PWRF2 ELOS1 ELOS2 ELOS ELOS3 ELOS4 EAIS1 EAIS2 EAIS3 EAIS4 OAIS...
  • Page 50 CTC Union FMUX03 Fiber Optical Multiplexer Series CTC Union Technologies Co., Ltd. Far Eastern Edison Science and Technologies Center (Nei-Hu HI-TEC Park) 6F-3, Lane 360, Nei-Hu Road, Section 1 Nei-Hu, Taipei, Taiwan Phone:(886) 2.2659.1021 (Rep) Fax:(886) 2.2799.1355 mailto:info@ctcu.com E-mail: http://www.ctcu.com...

Table of Contents