Page 1
PORTI-SW40/45 MODEL (3inch Mobile Printer) Rev. 3.1 All specifications are subjected to change without notice. http://www.woosim.com...
Page 2
Copyright ⓒ2018 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc.
Page 3
Introduction The PORTI-W40 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. PORTI-SW40/45 The general features of printer are as follows: Compact size (107.4 x 88.5 x 45mm) ...
Page 4
Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. ● Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. ● Do not use chemical glue. ● Always use the clean thermal paper. http://www.woosim.com...
Page 5
ㆍChanges and modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ㆍIt is desirable that it be installed and operated with at least 20cm or more between the radiator and person’s body(excluding extremities hand, wrists, feet, and ankles) http://www.woosim.com...
3. Interface ................................19 3.1. UART(RS-232C or TTL) ..........................19 3.2. Bluetooth ..............................19 4. Using the printer ...............................20 4.1. Control panel..............................20 4.2. The self test ..............................20 5. Consumable Parts .............................21 5.1. Recommended paper ..........................21 5.2. Printing position ............................21 6. Revision History ..............................22 http://www.woosim.com...
None : DC 8.4V Standby symbol IEC 5009, the standby symbol(line partially within a broken circle), Indicates a sleep mode or low power state. Direct current symbol This symbol is found on many electronic devices that either require or produce direct current. http://www.woosim.com...
2. Porti-SC30 Bluetooth Only Part No. ⇒ SC30/Z1 Note) The above table is the interface format which is supported. But some of the interfaces are not supported according to the product and please contact us, if you have any questions regarding the interface. http://www.woosim.com...
PORTI-SW Rev. 3.1 & & Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Communication cable Battery Pack PORTI-SW40/45 Battery charger adaptor Thermal roll paper ▼ OPTIONAL External Battery Cradle http://www.woosim.com...
2. Open the paper cover using finger on both side of printer, and remove the remaining paper. 3. Insert the paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.woosim.com...
- Turn the printer power off and push the battery pack lock and to lift up the direction of the arrow. ③ The battery pack install into External Battery Cradle. - Insert the battery pack in the direction of the arrow. http://www.woosim.com...
The recharging time depends on the voltage level and ambient temperature of the battery. Normally, if takes about 4 hours to recharge a battery pack. ● You must use only the supplied adapter. ● Red Lamp : charging the battery. Green Lamp : charging is finished. http://www.woosim.com...
And then the Parity bit has set to Odd parity bit. When you press FEED Button once again, Power Lamp flickers 5 times Error Lamp flickers once. Press MODE Button once, Error Lamp flickers twice. And then the density has set to 2 stop bit. http://www.woosim.com...
Page 17
(Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 stop bit / Density high / Mark no use / Sensor medium1 / Power down no use) If the status is not correct, please try it again according to the procedure. http://www.woosim.com...
Page 18
1 stop bit Stop bit 2 stop bit Density Low Density Density Medium Density High No use Mark Medium1 Sensor Medium2 High No use 1 minute 2 minute Power Down 3 minute 4 minute 5 minute < Table 2 > http://www.woosim.com...
PORTI-SW Rev. 3.1 (Fig.3.1) The Porti-SW40/45 printer has a UART(RS-232C or TTL) interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: Pin No.
3. Printer will print out the current status. (F/W version and set contents) 4. And then pattern of characters will be printed out. 5. Self-test will be finished automatically and turned to the standby status. ※ In case printer does not work properly, please contact Woosim customer service center. http://www.woosim.com...
2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃. Pay attention to heat, humidity and sun light. 4. Color of paper may be changed by being scratched by nail or hard metal, etc http://www.woosim.com...
Need help?
Do you have a question about the PORTI-SW40 and is the answer not in the manual?
Questions and answers