Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Watersnake Saltwater ASP T-18
Summary of Contents for Watersnake Saltwater ASP T-18
- Page 1 KAYAK MOTOR BRACKET COMBO OWNERS MANUAL...
- Page 2 20 - 40 AMP HOUR ** ** NOTE - this is to be used as a guide only. Check with your battery supplier to confi rm required size of 12 volt deep cycle marine battery that will be appropriate for your situation. Watersnake...
- Page 3 Watersnake motor • Select desired mounting location on boat • 12 v deep cycle marine battery (your Watersnake motor is not designed for use with car / truck / motorcycle type batteries) – for more information about appropriate batteries for your Watersnake motor, refer to page 10 •...
- Page 4 WATERSNAKE ELECTRIC MOTORS Congratulations and welcome to a world of silent motoring. Powerful yet silent, the Watersnake electric motors are built to suit all angling conditions. High quality materials, superior design and precision engineering make these motors longwearing and reliable.
- Page 5 Assemble both swivel clamps as shown. Then assemble as shown. Do not fully tighten the bolt at this stage just tighten it enough to hold the parts in place. Once Put together you unit should look like unit should look like diagram 1. www.watersnake.com.au...
- Page 6 Scan this QR Code to watch a video about this bracket with instructions on how to assemble and install it on your kayak. To watch this video you can also visit: https://www.jarviswalker.com.au/ watersnake-kayak-motor-bracket- combo.html Watersnake...
- Page 7 The Head units controls are easy to use. There is a switch for forward and reverse ( I o R ) and a switch for low (-) or high speeds (=). Low and high speed switch Forward / reverse and off switch www.watersnake.com.au...
- Page 8 2: Align the propeller against the shear pin on the shaft (there is a groove on the back of the propeller which the shear pin needs to slot into) and then tighten the propeller nut securely. Shear pin Propeller Propeller shaft Propeller Watersnake...
- Page 9 50 amps. Anderson plugs are a popular choice amongst many Watersnake motor owners and are readily available. A Watersnake circuit breaker is highly recommended. Attach to the red power cable to protect the circuit boards of the motor.
- Page 10 Use of car / truck / motorcycle batteries can cause damage to electronic components within your Watersnake motor. STOWING When your Watersnake motor is not in use always stow and store it properly. Watersnake...
- Page 11 ( I o R ) and a switch for low (-) or high speeds (=). The handle of the motor head is stowable and extends with the pull of a button. This makes the motor more compact and easier to store away when not in use. Pull button to extend handle. www.watersnake.com.au...
- Page 12 MAINTENANCE Your Watersnake Electric Motor should provide many seasons of dependable service. However, like any tool, electric motors must be cared for. After each day of fi shing, the motor should be cleaned thoroughly. A light rinse with fresh water (do not direct a high pressure stream of water at the motor) and wash with warm soapy water to remove any remaining salt / debris particles should be completed.
- Page 13 Upon connecting your battery to your motor, and before setting off in your boat, make sure that your trolling motor is mounted correctly. Of course once you engage your Watersnake motor for use make sure that it is in the right place, not too low or too high. It is recommended not to run your trolling motor out of water for long periods of time.
- Page 14 A signifi cant number of issues can be caused by a disruption of power supplied to your Watersnake motor. Careful inspection of your 12v deep cycle battery, wiring and fuse / circuit breaker set up should be completed before assuming that there is a fault with your motor.
- Page 15 • Lubricate shaft with spray lubricant A number of service videos are available on the Jarvis Walker Brands Youtube channel – search “Jarvis Walker Brands” from the Youtube search function. Please contact Jarvis Walker or your nearest service agent should issues persist. www.watersnake.com.au...
- Page 16 Hi -Low 2-Blade 55527 ASP T-24 WHITE 24lb 9-20 108-240 1900 24" Kayak Hand Hi -Low 2-Blade Model range and specifi cations are correct at time of printing. For new models not listed here fi nd specifi cations at: www.watersnake.com.au Watersnake...
- Page 17 ASP T-18 MOTOR www.watersnake.com.au...
- Page 18 Watersnake...
- Page 19 www.watersnake.com.au...
- Page 20 ASP T-24 MOTOR...
- Page 21 Watersnake Propeller Kits (Sold Separately) Watersnake Propeller kits contain a propeller, nut and shear pins. It is recommended you keep a spare propeller on your boat at all times. The Mini 2- Bladed Kit is suitable for the T-18 and T-24 motors. The 2-Bladed Propeller Kit is suitable for 28lb, 30lb and 34lb motors.
- Page 22 Watersnake Trolling Motor Connectors Watersnake Motor Connector Plugs makes it very quick and simple to remove and replace your motor from the boat as well as providing a better connection to your power source. Available in a 12v plug. 55505...
- Page 23 Watersnake offers an extensive range of PFDs for both adult’s and children. They come in a range of styles and sizes and they all meet the Australian and New Zealand safety standard. See your nearest Watersnake stockist for the full range or visit our website:www.watersnake.com.au for more information.
- Page 24 +0303 798 744 Watersnake ® and Jarvis Marine ® are registered trademarks of Watersnake Distribution Pty. Ltd. United Kingdom Masterline Walker +44 0 1684 299 000 © Watersnake Distribution Pty. Ltd. All Rights Reserved. Specifications are subject to change without notice.
Need help?
Do you have a question about the Saltwater ASP T-18 and is the answer not in the manual?
Questions and answers