ISOUND BT-200 User Manual

Includes:
BT-200, charge cable, 2 removable ear clips, 2 sets of silicone tips (S/L), removable cable management clip, and user guide
Please read and follow this user guide thoroughly before using the BT-200.
1. Microphone
2. Volume Down/Track Back
3. Charge Port

Specifications

Frequency response: 20 Hz – 20 kHz
Driver size: 10mm
Impedance: 16 omega
Sensitivity: 110±5dB
Bluetooth v .1 + EDR, up to a 30 foot transmission range 4
Battery capacity: 70mAh
Play time: Up to 2.0 hours based on usage
Charge time: 2 hours

Button functions

Power/phone button
• Press and hold for at least 5 seconds to power on the BT-200; press and hold for at least 5 seconds
to power off the BT-200.
• When playing music, press and release to pause music; press and release again to play music.
• When receiving an incoming call, press and release to answer; press and release again to
end the call; press and hold for 3 seconds then release to reject the call.
• Press twice quickly to call last number dialed.
• When a user is connected and the BT-200 is off, press and hold for at least 5 seconds to
unpair from Bluetooth (allow another user to connect).
NOTES:
• During the first time set-up, you must hold the power/phone button down until you hear a voice say
"Power on", then followed by "Ready for pairing" in order to sync your device to Bluetooth. After the initial pairing, you can let go of the power/phone button after you hear a
voice say "Power on".
• When playing music and a call comes in, the music will pause and you will hear a ringtone.
The music will resume when the call is ended. Device's ringtone may vary.??
• If you reject a phone call, you will hear a voice say "Phone call rejected" and your music will
resume playing. If the music does not begin, press and release the power/phone button again to
resume the current track.
• The power/phone button functions may vary per device.
Volume up/track forward button
• Press and release to raise the volume.
• Press and hold to go to the next track.
NOTE: The volume up/down buttons may control the volume on your device. Device's results may vary.
Volume down/track back button
• Press and release to lower the volume.
• Press and hold to go the previous song.
NOTE: The volume up/down buttons may control the volume on your device. Device's results may vary.

Charging your BT-200

NOTE: Make sure your BT-200 is fully charged before using it the first time.
1. Gently plug the Micro-USB end of the included charge cable into the charge port of the control box.
2. Plug the USB A end of the cable into a powered USB port, such as a computer, laptop, or USB AC adapter (not included).
3. The LED power indicator located next to the volume up/track forward button will light up solid red. Once the headset is fully charged, the LED
NOTES:
• When the battery level is below 10%, you will hear a voice say "Battery level low".
Charge your BT-200 with the included charge cable. This feature only works while the BT-200 is on.
• The LED power indicator will light up red while charging even if the BT-200 is off.
• You can charge your BT-200 while listening to music, however, this extends the charging time.
Connecting via Bluetooth® (first time set-up)
1. Press and hold the power/phone button for at least 5 seconds to turn the headset on.
You will hear a voice say "Power on", then continue to hold the button until you hear "Ready for pairing" and the LED power indicator will rapidly flash blue and red.
NOTE: During the first time set-up, you must hold the power/phone button down until you hear a voice say "Power on" then followed by "Ready for pairing" in order to sync
your device to Bluetooth. After the initial pairing, you can let go of the power/phone button after you hear "Power on".
2. Open the settings on your Bluetooth device. (Bluetooth must be enabled)
3. Select "BT-200" from the list of Bluetooth devices.
4. Once paired, you will hear a voice say "Device connected". The LED power indicator light will flash blue slowly.
5. To turn off the BT-200, press and hold the power/- phone button for at least 5 seconds. You will hear a voice say "Power off" before the headset turns off.
NOTES:
User Guide
4. Power/Phone
5. Volume Up/Track Forward
6. LED Power Indicator
BT-200
power indicator will turn off.