Table of Contents
Advertisement
Programmable
Thermostats
®
61152P
User
Manual
62152P
Model number is located on back of thermostat
1 Specifications
2 Installation
3 Setting User Options
4 Setting Your
Program Schedule
Warning
Turn off power to the heating or cooling
equipment before installation.
Attention
For installation by experienced service
technicians only.
Read all instructions before proceeding.
This thermostat requires 24 Volt AC Power or two (2) properly installed
"AA" Alkaline batteries for proper operation. When connecting 24 Volt
AC Power the batteries may be installed as a backup.
For use only as described in this manual. Any other use will void warranty.
1 Specifications
This thermostat is compatible with:
Electrical and control specifications:
Terminations
5 Operating Your Thermostat
6 Additional Operation Features
7 Thermostat Maintenance
61152P-100-01
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
Advertisement
Table of Contents
Related Manuals for CTC Union 62152P
Summary of Contents for CTC Union 62152P
-
Page 1: Programmable Thermostats
Programmable Thermostats ® 61152P User Manual 62152P Model number is located on back of thermostat 1 Specifications 5 Operating Your Thermostat 2 Installation 6 Additional Operation Features 7 Thermostat Maintenance 3 Setting User Options 4 Setting Your Program Schedule Warning Turn off power to the heating or cooling equipment before installation. -
Page 2: Installation
2 Installation Warning Disconnect power before beginning installation. Thermostat Location Install your new CTC ® thermostat in 5 basic steps: Install the Sub-Base: Drill 3/16” pilot holes in your desired location. Use supplied anchors for drywall or plaster. Provide Power For 24 Volt AC power For primary or back-up power... -
Page 3: Connect Your Wires
Set Installer Switch to CONV [note 2] [note 2] W1/E [note 1, 3] 2 HEAT / 1 COOL Single or Dual Transformer (62152P Only) Set System Type to CONV [note 2] [note 2] [note 1, 3] NOTES - Conventional Systems... - Page 4 1 HEAT / 1 COOL - No Auxiliary Heat Set Installer Switch to HP O or B [note 2] [note 1] 2 HEAT / 1 COOL - Including Auxiliary Heat (62152P only) Set Installer Switch to HP O or B [note 2] [note 3]...
-
Page 5: Attach Thermostat To Sub-Base
Attach Thermostat to Sub-Base 3 Setting User Options Advanced User Options To enter the User Options menu, hold down the RETURN button for 3 seconds until the screen changes and displays the first User Option. Table of User Options User Factory Setting Options... -
Page 6: Setting Your Program Schedule
4 Setting Your Program Schedule Setting the Time and Day DAY/TIME DAY/TIME DAY/TIME RETURN Tips Before Setting Your Program Schedule Residential 5-2 Day Programming– Weekday/Weekend Factory Settings 4 Event Time: 6:00 am Time: 6:00 am Heat: 70˚ F (21˚ C) Heat: 70˚... -
Page 7: Operating Your Thermostat
Additional Switch Position (Model 62152P Only): EMER NOTE: If your model 62152P was configured for a conventional system (CONV) then you will not have the EMER (emergency heat) option and “NO EMER SET” will flash in the display if EMER is selected with the system switch. -
Page 8: Additional Operation Features
Program Event Indicators NOTE: You will not see a program event indicator while in HOLD Mode. Resetting the Thermostat 6 Additional Operation Features Compressor Protection 7 Thermostat Maintenance Changing the Batteries If batteries are installed and they become low, a low battery indicator will appear in the display. NOTE: We recommend replacing the thermostat batteries annually or if the thermostat will be unattended for an extended period of time.
Need help?
Do you have a question about the 62152P and is the answer not in the manual?
Questions and answers