Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Vdwall LVP300
Summary of Contents for Vdwall LVP300
- Page 1 LVP300 LED HD Video Processor User Manual V1.1...
-
Page 2: Table Of Contents
2. Input video signal setting..............................20 3. Text overlay setting................................22 4. Image quality setting................................25 5. Language setting................................. 25 6. Advance setting..................................26 7. PIP / PBPsetting.................................. 29 Chapter 7: LVP300 PC control software instruction....................30 Chapter8: Copyright information..........................41 Appendix：modify the record table............................42... -
Page 3: Chapter 1 Safety Precautions
Chapter 1 Safety Precautions ！Danger There is high voltage in the processor, to prevent any unexpected hazard, unless you are maintenance, please do not open the cover of the device. ！Warning 1. This device shall not encounter water sprinkle or splash, please do not place anything containing liquid on this device. -
Page 4: Chapter 2 Item List
LVP300 LED HD Video Processor Chapter 2 Item List Please unpack the product carefully, then check whether all the following things are included in the package. If anything is found missing, please contact the dealer. Standard accessories The accessories supplied with this LED Video Processor may differ from... -
Page 5: Chapter 3 Hardware Connection
LVP300 LED HD Video Processor Chapter 3 Hardware connection 1 Rear view ①Video input ports ②Video output ports ③Communication ports ④Sending card installation location 2 Ports description 1) Video signal inputs (INPUT) supports 6 video signals input as follows: LVP300... - Page 6 LVP300 LED HD Video Processor 2) Video signal output Port Description DVI OUT1 / 2 same DVI digital graphic signal outputs, can be DVI OUT2 connected to external 2 LED transmission cards or LED transmission boxes. SDI OUT 1 SDI Loop output(Only exist when Extended module is SDI)
-
Page 7: Specifications
LVP300 LED HD Video Processor 4. Specifications Inputs 2×CVBS 1×VGA（RGBHV） Nums / Type 1×DVI（VESA） 1×HDMI（VESA/CEA-861） 1×EXT.（Extension） Video system PAL / NTSC Composite Video Amplitude 1V（p_p）/ 75Ω Impedance... - Page 8 LVP300 LED HD Video Processor VGA Format PC （VESA standard） ≤1920×1080_60Hz Amplitude R、G、B = 0.7 V（p_p）/ 75Ω Impedance DVI format PC （VESA standard） ≤1920×1080_60Hz PC （VESA standard） HDMI format ≤1920×1080_60Hz HDMI1.3 （CEA-861） MKV/TS/M2TS/TP/TRP/AVI/WMV/RM/RMVB Multimedia video file format /MPEG/MPG/MP4/VOB/MOV/ISO/DAT/ASF H.265 AVC HD、VC-1(WMV HD)、...
- Page 9 LVP300 LED HD Video Processor others Control RS232 Input voltage 100-240VAC 50/60Hz Power ≤25W consumption Environment 0-45℃ Temperature Environment 15-85% Humidity Product Size 482.6（L）x283（W）x49（H）mm weight Gross weight：4.6Kg, Net weight： 3Kg 5. Product Size RS232 cable order：...
- Page 10 LVP300 LED HD Video Processor...
-
Page 11: Chapter 4: Front Panel
LVP300 LED HD Video Processor Chapter 4 Front panel buttons 1 Input signal selection buttons（V1，V2，VGA，HDMI，DVI，EXT.，Take） ： select the input signal. Setup buttons ( Setup，↑，↓，旋钮 ) Knob Set the output image parameters. VGA auto adjustment button ( Auo ) automatically adjust the VGA input signal. - Page 12 LVP300 LED HD Video Processor turn on / off freeze function. Brightness adjustment button 8） （Brt+，Brt-） adjust output brightness level under user operation station.
-
Page 13: Chapter 5 Basic User Instructions
LVP300 LED HD Video Processor Chapter 5 Basic user instructions After LVP300 boot, it enters the operation status of last shut-down including signal switching status, PIP/POP (or Text overlay) status and mosaic status. Among them, PIP/PBP( or text overlay) status and mosaic status can only realize relative functions and cannot do other operation. - Page 14 LVP300 LED HD Video Processor One key switch 1） LCD screen display as below ： After select input signal, The first line on the LCD display the current input signal. Like： “ Input： HDMI ” 。 The second line on the LCD display the signal status.If no active input, display”...
- Page 15 Switching effect includes seamless switching (0s), Fade in/ Fade out (o.5s 1s 1.5s) and blend switching. Seamless switching（Cut） ：On the LCD“Switch time” is 0s. LVP300 default switching is CUT. Fade in fade out（Fade） ：On the LCD“Switch time”is 0.5s、1.0s or 1.5s. In this mode,...
-
Page 16: Pip/Pbp Operation
LVP300 LED HD Video Processor 2. PIP/PBP operation LVP300 allows to insert PIP window on the current display signal. That is dual image display function(PIP/PBP)。PIP signal can be any input signal from other input groups or current input signal itself. （signal group refer to page signal group list）Dual image size... - Page 17 VGA input auto adjustment ( Auto ) 2） When LVP300 is in one key switch status and current valid input signal is VGA, press Auto button to adjust VGA input signal sampling parameters. Then the VGA output image can be clear and full.
- Page 18 Part display is invalid. Text overlay 4） LVP300 allows for overlapping text, logo or flash on the current image. The operation is as below. When the current input display properly, enter setup menu“3.Text overlay”，set ”3.1 text overlay” on，then select text source.Text can be produced by PowerPoint and other office software.
-
Page 19: Chapter 6: Setup Menu Instructios
LVP300 LED HD Video Processor Chapter 6: Setup menu instructions Setup menu is to set the entire processor. There are 7 section including output image、 input image、text overlay、image quality、language、advance、PIP/PBP. setup -------------------------------------- ＞＞ Out Image ＞＞ Input Video Signal ＞＞ Text Overlay 4. - Page 20 LVP300 LED HD Video Processor Set output format 1） LVP300 can output image from 2 DVI OUT. There are 10 fixed output format and custom output format.（refer to page 8 specifications）. Users can select fixed output format not less that the LED screen resolution.
- Page 21 LED screen real resolution can be arbitrary. So we need set LVP300 to output the same image as the led screen. Then the LED screen can display whole image. As shown in the above picture: the size and location of output image of LVP300 can be defined in 4 parameters: Item NO.
-
Page 22: Input Video Signal Setting
LVP300 LED HD Video Processor Test pattern 3） LVP300 can generate 36 test patterns for LED screen testing. If this item value is “off”, turn off Test pattern. Select other number and confirm.Then one corresponding test pattern of 36 pcs will be selected. -
Page 23: Text Overlay Setting
LVP300 LED HD Video Processor DVI EDID 1） VP300 supports 10 fixed DVI EDID. Normally the parameters setting should be consistent with“custom output format”. Operation steps ： In the menu 2.1 DVI EDID ， rotate knob to select suitable resolution and press OK to save data. - Page 24 If need turn it off, enter 3.1 text overlay and switch it off. Text overlay parameters setting 2） 3.1Text mode ： LVP300 can custom text mode < threshold or > threshold. < threshold means text signal image which is less than the current threshold value will overlay on the current signal.
- Page 25 LVP300 LED HD Video Processor Main picture text text overlay...
-
Page 26: Language Setting
To make sure of full gray scale of output image, these output parameters are set Note： as default! Color parameters are invalid for RGB format VGA, DVI and HDMI. 5. Language setting LVP300 supports Chinese and English language.Rotate knob to select one and press OK to save. -
Page 27: Advance Setting
LVP300 LED HD Video Processor Language -------------------------------------- 5.1 语言 Language Chinese 6. Advance setting 6.advance default -------------------------------------- 6.1 ADC calibration OK to apply 6.2 Bias 6.3 EXT.Input model EXT.VIDEO 6.4 De-Interlace 6.5 Bright level 0-64 6.6 DVI hotplug 6.7 Device reset OK to apply 8.6 DVI 热插拔... - Page 28 LVP300 LED HD Video Processor ADC Calibration 1） “6.1 ADC Calibration” is used to calibrate the white balance of analog signals to avoid color cast or extreme darkness problem. This function is only available for non ext. Input VGA,CVBS. The operation way is as follow：...
- Page 29 7） The menu is used to initialize LVP300. Operation as below: Enter “6.7Device Reset” and press OK button, there is one information on LCD screen to remind you data will reset. Press OK to apply. LVP300 will reset and restart.
-
Page 30: Pip / Pbpsetting
The setup option is used to set LVP300’s three user defined PIP/PBP mode. Operation as below: When LVP300’s PIP/PBP status is open (the indicator light on “On/Off” button is lit up), press Setup button, LVP300 enters “D. PIP/PBP” menu. Then press mode button (M1, M2 or M3) to select a mode to save parameters, press ↓... - Page 31 LVP300 LED HD Video Processor Chapter 7 PC control software instructions LVP300 control software is applied to operate LED Video Processors. We can do such operations as below via this software: Seamless Switching And Fade-In/Fade-Out 3 User-Definable Dual Windows Display Modes And Text Overlap ...
- Page 32 LVP300 LED HD Video Processor ① Communication Settings ② Language Settings ③ Signal Switching ④ Modes Selection ⑤ Info Bar ⑥ Timing Control Settings ⑦ Output Parameters Settings(Screen Settings) ⑧ Output Resolution Settings Communication Settings 1） The default connection method is via COM port among Communication Settings. You need to select the right COM port and you can check which is the right one on Device Manager view, it is shown in this picture below.
- Page 33 LVP300 LED HD Video Processor Timing autostart settings： to decide whether it will connect with this processor automatically and start-up timing control automatically the next time it is power on.
- Page 34 LVP300 LED HD Video Processor Language Settings 2） LVP300 software supports 2 optional languages used on the main interface. Signal Switching 3） The buttons in “Source” area is corresponding to those buttons and status indicator on the front panel. After connecting successfully, a blue dot nearby will light up to indicate that this signal source is effective.
- Page 35 LVP300 LED HD Video Processor Modes Selection 4） These buttons in this area are used to display under PIP status, text overlap, bypass, freeze stream which is playing and mosaic. PIP/PBP: This button is used to turn on or turn off function PIP/PBP, the blue dot above will tell you whether it is on or off.
- Page 36 LVP300 LED HD Video Processor Info Bar 5） If there occurs a failure, the info bar will show you the reason why it is failed. Timing Control Settings 6） The timer in the software can switch input signals on time set before. And there are 4 modes you can choose including daily timing, weekly timing, monthly timing and freely timing.
- Page 37 LVP300 LED HD Video Processor Timer parameter settings 7） Click this button Program on the main interface and this box below will appears. Schedules are classified into two types: ① Cyclical schedule ② One-off schedule Meanwhile, cyclical schedules are classified into 3 types: ①...
- Page 38 LVP300 LED HD Video Processor You can add, modify or delete every schedule，the example below shows you how to add one-off schedule. Select an added schedule, then you can modify or delete it. Output Parameters Settings 8） Click Screen Program on the main interface, an interface of output parameter settings will...
- Page 39 LVP300 LED HD Video Processor As the picture showed above, the button “refresh” is set there to reread parameters set before. The info bar is used to indicate Exception information currently. A background in blue reminds you that you are typing and the value of parameters have not been saved, while a background in grey means all the parameters have already been saved successfully.
- Page 40 LVP300 LED HD Video Processor ② Dual Images Settings This interface below is used for settings for 3 PIP/PBP modes. We need to make sure that the PIP function has already been turned on before setting. Firstly, we need to enter the PIP mode you selected, then we input values of background’s size and PIP window’s size, save it after...
- Page 41 Remark: the default values of color and low ash bias are all 50. output Resolution settings 9） Click Resolution on the main interface of LVP300 software and this popup will appear above. Users can set this output resolution as you will.
-
Page 42: Chapter8: Copyright Information
Chapter 8 Copyright information The copyright of this Manual is owned by SHENZHEN VDWALL CO.,LTD., unless with prior consent of VDWALL, nobody is permitted to copy or use any part or all of the information contained herein. This Manual is provided for reference only, VDWALL reserves right to change the product appearance, dimensions and specifications from time to time without notice to users. -
Page 43: Appendix：modify The Record Table
LVP300 LED HD Video Processor Appendix：modify the record table version time description draft V1.0 2017.9.27 LVP300 first release...
Need help?
Do you have a question about the LVP300 and is the answer not in the manual?
Questions and answers
Output video to a screen
To output video to a screen using the Vdwall LVP300, follow these steps:
1. Press the "Setup" button to open the setup menu.
2. Use the ↑ or ↓ buttons to select “1. Out image” and press OK.
3. Select “1.1 Resolution” and rotate the knob to choose a resolution that is equal to or greater than the LED screen resolution (e.g., 1280×1024_60).
4. Press OK to confirm the resolution. A confirmation menu will appear.
5. Press OK again to confirm. The device will restart automatically.
6. Set the output image parameters to match the LED screen's real resolution and position so the whole image displays correctly.
The output will be through the two DVI OUT ports.
This answer is automatically generated