1. Manuals
  2. Brands
  3. Reiner Manuals
  4. Office Equipment
  5. jetStamp graphic 970
  6. Operating manual

Reiner Jetstamp graphic 970 Operating Manual

Hide thumbs Also See for Jetstamp graphic 970:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Jetstamp graphic 970 and is the answer not in the manual?

Questions and answers

Related Manuals for Reiner Jetstamp graphic 970

Summary of Contents for Reiner Jetstamp graphic 970

  • Page 2: Table Of Contents

    ................................19 4.5.2 Installing Softw are ................................19 4.6 Firmware update ........................... 20 V The Software Application PCset graphic 5.1 Prepare jetStamp graphic 970 for PCset graphic ........................... 21 5.2 Starting the software ........................... 22 5.3 Operating Interface ........................... 22 5.3.1 Menu Bar ................................
  • Page 3 5.6.5.1 Context menu graphic object ................................. 72 5.6.5.2 Generate graphic ................................. 72 5.6.5.3 5.7 External print triggering ........................... 72 5.7.1 Trigger via USB interface ................................72 5.7.2 Trigger via External Sw itch ................................73 ERNST REINER GmbH & Co. KG...
  • Page 4 6.5 Replace Protective Nozzle Seal ........................... 81 6.6 Clean Housing ........................... 81 VII Recognising and Removing Interferences 7.1 jetStamp graphic 970 does not work ........................... 82 7.2 Reasons for rechargeable batteries not being charged ........................... 83 7.3 Visual Signals (LED) ...........................

  • Page 5: I Jetstamp Graphic 970

    970 jetStamp graphic 970 ERNST REINER GmbH & Co. KG...

  • Page 6: Operating Element

    PCset graphic Help 970 Operating Element ERNST REINER GmbH & Co. KG...
  • Page 7 Battery compartment Folding print cartridge Print carriage Print cartridge Basic station Lock print cartridge Seal Contact print cartridge LED indicator Nozzles Set wheel Sealing tip Green charge display Positioning aids Micro-USB socket Print area ERNST REINER GmbH & Co. KG...

  • Page 8: Set Wheel

    The LED indicator marks the selected setting and flashes in case of warnings. On the setting functions (see "Functions"). To avoid malfunctions align the settings precisely with the LED indicator! To activate Bluetooth, turn the setting wheel to position Online/Bluetooth (see "Activate Bluetooth"). ERNST REINER GmbH & Co. KG...

  • Page 9: Important Notes

    Important Notes Important Notes Before commissioning of the jetStamp graphic 970, always read the operating instructions and in particular the safety notes with care. This prevents mistakes in handling of the marking device and connected safety risks to keep you safe and avoid damage to the device.

  • Page 10: Your Safety

    Warnings of dangers that may lead to property damage if not observed. You are asked to perform actions here. Notes and advice to make handling your jetStamp graphic 970 even easier. Notes on instruction videos. ERNST REINER GmbH & Co. KG...

  • Page 11: Safety Notes On Rechargeable Batteries

    Type use Only use the enclosed plug-in mains adapter or a PC USB connection to charge the batteries. Only use rechargeable batteries (three each) of the nickel-metal-hydride type (REINER item number: 946 192 - 000), build AA. Always replace all rechargeable batteries at once.

  • Page 12: Safety Notes

    Possible blinding in case of contact between ink and eyes. Never hold the jetStamp graphic 970 with its nozzles pointing at the face of persons! Possible tripping and damage to the device from device lines placed freely in the room.

  • Page 13: Preparation And Taking Into Operation

    Firmware update Commissioning Find a clip on our homepage at www.reiner.de or youtube. The rechargeable batteries must be charged completely before the first use. The charging time is approx. 3 hours. The rechargeable batteries are charged when the green charge display goes out.

  • Page 14: Inserting Rechargeable Batteries

    Open battery compartment Place the textile ribbon flat across the compartment. The textile ribbon serves simpler removal of the rechargeable batteries. Ensure correct polarity and insert the batteries. Close battery compartment ERNST REINER GmbH & Co. KG...

  • Page 15: Charge Batteries

    Charging at a USB hub without dedicated power supply is not possible. Connect the Micro-USB socket of the device to the mains unit with the USB cable and connect the mains unit to the mains. Green charging indicator lights up. ERNST REINER GmbH & Co. KG...

  • Page 16: Inserting Printing Cartridge

    Do not swallow! Keep the print cartridge away from children. Inserting Printing Cartridge Fig. Put the jetStamp graphic 970 in the basic station Turn the setting wheel to position 1. Keep the trigger button pushed and take the device from the basis station Print carriage moves to the middle position.

  • Page 17: Test Printing

    Close the print cartridge flap Push the trigger button Print carriage moves to the home position. Return jetStamp graphic 970 to the basis station to prevent drying of the ink. Observe acoustic signal of the jetStamp graphic 970 (see "Acoustic Signals").

  • Page 18: Activate Bluetooth

    If Bluetooth is active, the battery runtime reduces since Bluetooth is active in standby mode as well. To activate Bluetooth at the device, the setting wheel must be turned to position Online/Bluetooth. To establish the Bluetooth connection with the device, follow the instructions "Establishing Bluetooth Connection". ERNST REINER GmbH & Co. KG...

  • Page 19: Install Pcset Graphic Software

    Installation is only possible with administrator rights on the computer. Insert PCset graphic-CD into the drive. If the installation programme does not start up automatically, start the file "setup.exe". Observe the installation programme's instructions. ERNST REINER GmbH & Co. KG...

  • Page 20: Firmware Update

    970 to the PCset graphic. The print images can be damaged during the Firmware update. Ensure that the PCset graphic is installed on your PC but not opened before the firmware update is started. While the firmware update is being installed, the jetStamp graphic 970 must not be switched off.

  • Page 21: The Software Application Pcset Graphic

    Turn the setting wheel to 1 to activate the device. The PC recognises the jetStamp graphic 970 as a new USB device. The device driver software is installed automatically. When the device is connected to the PC, the rechargeable batteries are charged via the USB connection.

  • Page 22: Starting The Software

    PCset graphic Help 970 Starting the software Double-click the REINER PCset graphic icon The PCset graphic software is started. Operating Interface The operating interface is structured in four areas: Menu bar with Windows-typical and Pcset graphic-specific functions Toolbar 4 lines for print pattern design...

  • Page 23: Menu Bar

    Terminates the PCset graphic. 5.3.1.2 Edit Function Description Delete Deletes selected objects. Copy Loads selected contents into the clipboard. Paste Paste contents from the clipboard. Deletes selected contents and sends them to the clipboard. ERNST REINER GmbH & Co. KG...

  • Page 24: View

    Help with detailed configuration notes and operating instructions in electronic form. Info Version information on the software. When the jetStamp graphic 970 is connected, the information on model, serial number and firmware version appear here. ERNST REINER GmbH & Co. KG...

  • Page 25: Toolbar

    Display the tab "Print settings” in the menu "Settings". Transfer The displayed print patterns are transferred to the device. The data present on the jetStamp graphic 970 are overwritten. Upload Save the print patterns saved in the device for processing.

  • Page 26: Setting Lines/Grid

    Each print line is structured by the number of selected or the selected grid size. Unites Grid/rulers are displayed in the selected unit. Unit Description Ruler is labelled in mm. inch Ruler is labelled in inch. Pixel Ruler is labelled in pixels. ERNST REINER GmbH & Co. KG...

  • Page 27: Selection

    (see "Font" and "Presettings"). Barcode The format settings offer several barcode formats (see "Presettings"). Graphic After insertion of a graphical object, a file selection window opens. Select the desired graphic and confirm with "Open". ERNST REINER GmbH & Co. KG...

  • Page 28: Device Safety

    The device safety locks printing and protects the print data from abuse. Devices without the current firmware version do not support device safety. The latest firmware version can be downloaded from www.reiner.de in the area "Downloads". The device safety can be set in the menu bar under tab "Extras...

  • Page 29: Set Passw Ord

    To deactivate the device safety, select the tab "Extras" in menu bar and click Device safety Set password". Click "Deactivate password protection". In the status display and the toolbar , the symbol changes from ERNST REINER GmbH & Co. KG...

  • Page 30: Passw Ord Forgotten

    When resetting the password, the jetStamp graphic 970 is reset to factory settings. All saved print patterns are deleted. The password can only be reset when the jetStamp graphic 970 has no device error. If the set password has been forgotten, it can be reset as follows:...

  • Page 31: Device Settings

    The Software Application PCset graphic 5.3.5 Device settings Device settings will only become active when they have been transmitted to the jetStamp graphic 970. Print settings Signals Functions Font 5.3.5.1 Print settings Print sequence Alignment Print intensity ERNST REINER GmbH & Co. KG...

  • Page 32: Print Sequence

    Print single line (setting wheel) The selected line is printed once per print trigger. Print lines in sequence All lines are printed in sequence, bottom-up, starting with the line (1,2,3,4) indicated on the setting wheel (1, 2, 3 or 4). ERNST REINER GmbH & Co. KG...

  • Page 33: Alignment

    The Software Application PCset graphic 5.3.5.1.2 Alignment Function Description Turned by 0° Turned by 180° The 180° rotation is not displayed in the PCset. The device considers the setting in print. ERNST REINER GmbH & Co. KG...

  • Page 34: Print Intensity

    PCset graphic Help 970 5.3.5.1.3 Print intensity Function Description Normal Default ink consumption. Economic Reduction of ink consumption. ERNST REINER GmbH & Co. KG...

  • Page 35: Print Start

    The Software Application PCset graphic 5.3.5.1.4 Print start Function Description Print trigger Print is printed once the trigger button is pushed. External print triggering Print is printed when the print signal is sent through the USB cable. ERNST REINER GmbH & Co. KG...

  • Page 36: Signals

    PCset graphic Help 970 5.3.5.2 Signals Activation or deactivation of acoustic signals for different events (see "Acoustic signals"). "Function performed": see tab "Functions". "Removable errors": see "Acoustic signals". ERNST REINER GmbH & Co. KG...

  • Page 37: Functions

    The Software Application PCset graphic 5.3.5.3 Functions Test print Repeat last imprint Continue numbering machines Reverse numbering machines Reset numbering machines to default ERNST REINER GmbH & Co. KG...

  • Page 38: Test Print

    The printout starts with print pattern no. 1 and is switched forward to the next print pattern each time it is triggered. The "Test print" for the jetStamp graphic 970 is performed as follows: Turn the setting wheel to position F.

  • Page 39: Repeat Last Imprint

    With the function "Repeat last imprint", the last imprint to be printed can be repeated (Numbering machine does not change, time is current displayed). The function "Repeat last imprint" is performed as follows for the jetStamp graphic 970: Turn the setting wheel to position F.

  • Page 40: Continue Numbering Machines

    The function "Continue numbering machines" allows to increment the numbers manually in a quick and easy manner. The function "Continue numbering machines" is performed as follows for the jetStamp graphic 970: Turn the setting wheel to position F. Push the trigger button.

  • Page 41: Reverse Numbering Machines

    With the function "Reverse numbering machines", the numbers can be quickly and easily manually decremented. The function "Reverse numbering machines" is performed as follows for the jetStamp graphic 970: Turn the setting wheel to position F. Push the trigger button.

  • Page 42: Reset Numbering Machines To Default

    The default value for upwards counting numbering machines is the minimum value, and for downwards counting ones, it is the maximum value. For the jetStamp graphic 970, the numbering machines are "Reset to default" as follows: Turn the setting wheel to position F.

  • Page 43: Font

    The Software Application PCset graphic 5.3.5.4 Font For "Font 1" and "Font 2", fonts can be stored for the objects date/time and numbered. Month abbreviations can be set individually. ERNST REINER GmbH & Co. KG...

  • Page 44: Status Displays

    Connection has been made via Connection has been made via Bluetooth Displays the fill level of the print Ink level cartridge in % Rechargeable battery level Displays the charge condition of the rechargeable battery Rechargeable battery full ERNST REINER GmbH & Co. KG...
  • Page 45 Device is connected via the USB cable Online-Bluetooth Device is connected via Bluetooth Offline - Device not on - USB cable not plugged in - Rechargeable battery empty Here, notes on troubleshooting Device messages are displayed ERNST REINER GmbH & Co. KG...

  • Page 46: Device Messages

    Print cartridge almost empty Insert a new print cartridge Please insert a new print Print cartridge almost empty cartridge Put the jetStamp graphic 970 Put the device back into the Print cartridges may dry out if not in the base station basis station...

  • Page 47: Establishing Bluetooth Connection

    All devices found and all devices that have been connected to the PCset graphic before are displayed with model and serial number. If the jetStamp graphic 970 is not found, start a new search run with the button "Search again". ERNST REINER GmbH & Co. KG...
  • Page 48 The window for password input opens. Enter the factory password "0000". The jetStamp graphic 970 is connected to the PCset graphic. The connected device is saved as permanent connection, so that the PCset graphic will always connect with this device once it is available.

  • Page 49: Example Workflow: Generate Print Pattern

    Entering own print patterns overwrites all 4 print patterns saved in the device. The factory pre- installed print patterns can be uploaded into the software and saved as XML files before ("Menu Commands"). Configure print pattern Transfer Print Pattern to the jetStamp graphic 970 Print print pattern Number of prints 5.5.1...

  • Page 50: Transfer Print Pattern To The Jetstamp Graphic 970

    Confirm the following dialogue window with Yes. The following message will appear after a few seconds if the transfer is successful. Confirm message with OK. The print pattern is saved in the jetStamp graphic 970 now and can be printed. ERNST REINER GmbH & Co. KG...

  • Page 51: Print Print Pattern

    Put the device on a level surface to be printed on. Push the trigger button Example print pattern 1 is printed. Return jetStamp graphic 970 to the basis station to prevent drying of the ink. Observe acoustic signal of the jetStamp graphic 970 (see "Acoustic Signals").

  • Page 52: Number Of Prints

    PCset graphic Help 970 5.5.4 Number of prints The number of possible prints with a full printer cartridge is displayed by placing the mouse points over the print image number. ERNST REINER GmbH & Co. KG...

  • Page 53: Settings Objects

    The font size is adjusted if the grid is on. Example: If a grid of 4 lines is set, the text object has the height of one line. Presettings Contextmenu text object Generate graphic ERNST REINER GmbH & Co. KG...

  • Page 54: Presettings

    Selection of desired font style from the list (standard, bold, italics or bold italics). Size Selection of the font size in points or input of the font size in points. Script Shows a list of available language scripts for the indicated font. ERNST REINER GmbH & Co. KG...

  • Page 55: Context Menu Text Object

    Converts the text into a graphic and attaches it to the current position. Note: the text can no longer be edited after conversion. Delete object Deletes the object. Enter or double click fastens the objet and is therefore inactive. ERNST REINER GmbH & Co. KG...

  • Page 56: Generate Graphic

    Font, font style, font size (see "Font") and format can be set.The date/time format can be globally preset. Additionally, deviating settings can be performed for every single date/time object (see "Context menu date/time object"). Up to five date/time objects can be placed. Presettings Context menu date/time object ERNST REINER GmbH & Co. KG...

  • Page 57: Presettings

    Select the tab "Format" and click "Date/Time" in the menu bar The configuration window for date and time appears. The tab “Date and time“ is structured in two areas: - Format for date and time - Font Tab date and time Tab options Font ERNST REINER GmbH & Co. KG...

  • Page 58: Tab Date And Time

    Minutes with two graphics (00 to 59) Seconds with two graphics (00 to 59) One character for twelve-hours format with the letters A or P Two characters for twelve-hours format with the letters AM or PM ERNST REINER GmbH & Co. KG...

  • Page 59: Tab Options

    The offset can be used to, e.g., have best-before dates calculated automatically. Click into the respective text field. Enter or select offset. Confirm with OK. The set values are added to the current system date. The result appears in the configuration view of the imprints ERNST REINER GmbH & Co. KG...

  • Page 60: Font

    5.6.2.1.3 Font Selection option between "Font1" and "Font 2". "Font 1" and "Font 2" can be configured in the menu bar under tab "File Settings Font" or in the toolbar via the button (see "Font"). ERNST REINER GmbH & Co. KG...

  • Page 61: Context Menu Date/Time Object

    Observe: The following configuration may lead to nonsensical numbering machine readings: - Print sequence "Print lines in sequence" - Linked numbering machines with different repetitions each Presettings Context menu numbering machine object ERNST REINER GmbH & Co. KG...

  • Page 62: Presettings

    Select the tab “Format“ and click “Numbering machine“ in the menu bar The configuration window for numbering machines appears. The configuration window for numbering machine is structured in three areas: - Numbering machine settings - Number circle - Font Numbering machine settings Number circle Font ERNST REINER GmbH & Co. KG...

  • Page 63: Numbering Machine Settings

    This value marks the lower limit of the number circle. Maximum This value marks the upper limit of the number circle. Actual value The current counter reading can be set within the defined value range. ERNST REINER GmbH & Co. KG...

  • Page 64: Font

    5.6.3.1.3 Font Selection option between "Font1" and "Font 2". "Font 1" and "Font 2" can be configured in the menu bar under tab "File Settings Font" or in the toolbar via the button (see "Font"). ERNST REINER GmbH & Co. KG...

  • Page 65: Context Menu Numbering Machine Object

    Settings for the number circle can only be made here when the selected numberer is linked to the dedicated number circle. Delete object Deletes the object. ERNST REINER GmbH & Co. KG...

  • Page 66: Barcode

    Global presettings can be set in the menu bar via the tab "Format Barcode". - OR - Settings of already-inserted barcode objects can be called via the right mouse button "Barcode Format". The configuration window for barcode appears. ERNST REINER GmbH & Co. KG...
  • Page 67 Indicates the check figure additionally in plain text. To be able to use this option, you need to activate display plain text. The check figure is the last digit or position of the barcode information. ERNST REINER GmbH & Co. KG...
  • Page 68 Module ratio X:1 Ratio of wide to narrow element in calculation of the code length. Module ratio Start and stop characters for the barcode type coda bar. May (2/5 matrix) contain letters A - D. ERNST REINER GmbH & Co. KG...

  • Page 69: Continuous Numbering/Dating

    The context menu opens (see "Date/time"). Make the desired settings and confirm with OK. To save the settings made, click OK. The red dash below the editing field determines the inserted position of the date/time and numberer object. ERNST REINER GmbH & Co. KG...

  • Page 70: Context Menu Barcode Object

    Text and barcode objects can be converted to graphics. Graphics are fixed and cannot be moved. Limited editing is possible via the additional function "Selection". Click object with the right mouse button. Select "Generate graphic". The object is converted into a graphic. ERNST REINER GmbH & Co. KG...

  • Page 71: Graphic

    300 dpi to match the print pattern 1:1. For distortion-free printout in bet quality, a graphics should not exceed the maximum height of 160 pixels and the maximum width of 768 pixels. ERNST REINER GmbH & Co. KG...

  • Page 72: Context Menu Graphic Object

    Click object with the right mouse button. Select "Generate graphic". The object is converted into a graphic. External print triggering REINER optional accessories are available for external trigger types. Trigger via USB interface Trigger via External Switch 5.7.1 Trigger via USB interface...

  • Page 73: Trigger Via External Switch

    Triggering via external switch uses a galvanically insulated contact. An external voltage source is required for triggering - DC 2,4 - 24 V. Connect the REINER trigger cable to the plug-in socket for external triggering Set setting wheel to the desired print pattern.

  • Page 74: Maintenance

    PCset graphic Help 970 Maintenance Replace Print Cartridge Clean Print Cartridge Contacts Cleaning Nozzles Clean Protective Nozzle Seal Replace Protective Nozzle Seal Clean housing ERNST REINER GmbH & Co. KG...

  • Page 75: Replace Print Cartridge

    Do not swallow! Keep the print cartridge away from children. Replace Print Cartridge Fig. Put the jetStamp graphic 970 in the basic station Turn the setting wheel to position 1. Keep the trigger button pushed and take the device from the basis station Print carriage moves to the middle position.

  • Page 76: Clean Print Cartridge Contacts

    Closing the print cartridge flap Push the trigger button Print carriage moves to the home position. Return jetStamp graphic 970 to the basis station to prevent drying of the ink. Observe acoustic signal of the jetStamp graphic 970 (see "Acoustic Signals").

  • Page 77: Cleaning Nozzles

    Maintenance Put the jetStamp graphic 970 in the basic station Turn the setting wheel to position 1. Keep the trigger button pushed and take the device from the basis station Print carriage moves to the middle position. Gently push the lock of print cartridge...

  • Page 78: Automatic Cleaning Of Nozzles

    PCset graphic Help 970 6.3.1 Automatic Cleaning of Nozzles Possible blinding in case of contact between ink and eyes. Never hold the jetStamp graphic 970 with its nozzles pointing at the face of persons! Trigger automatic cleaning mechanism Fig. A small amount of ink is ejected for cleaning of the nozzles Take the device from the basis station and put it on a level surface.

  • Page 79: Manual Nozzle Cleaning

    To loosen the dried ink, gently wipe a soft cloth possibly moisten slightly with Ethanol (spirit) against the nozzles for approx. three seconds. Dab off dissolved ink and wipe the nozzles dry. ERNST REINER GmbH & Co. KG...

  • Page 80: Clean Protective Nozzle Seal

    Dab the Protective Nozzle Seal clean with a soft cloth. Clean the Protective Nozzle Sealat regular intervals. Replace at stronger contamination or damage (see "Replace Protective Nozzle Seal"). ERNST REINER GmbH & Co. KG...

  • Page 81: Replace Protective Nozzle Seal

    Maintenance Replace Protective Nozzle Seal Find a clip on our homepage at www.reiner.de or youtube. Replace Protective Nozzle Seal Fig. Depending on ink type used, different Protective Nozzle Seals are required. - Inkjet print cartridge P3-S-BK: use red seal - Inkjet print cartridge P3-MP3-BK: use blue seal Push down the Protective Nozzle Seal slightly at the front edge.

  • Page 82: Recognising And Removing Interferences

    Visual signals (LED) Acoustic signals jetStamp graphic 970 does not work Troubleshooting Fig. Remove the USB cable from the jetStamp graphic 970. Open battery compartment Remove the rechargeable batteries. Wait for approx. 3 seconds. Replace the rechargeable batteries. Connect the micro-USB socket of the device to the computer via the USB cable.

  • Page 83: Reasons For Rechargeable Batteries Not Being Charged

    - Print cartridge not inserted - Rechargeable Charge recharge- battery empty able battery - No rechargeable Insert/replace battery/defective rechargeable battery rechargeable battery - Print carriage movement Transfer new print blocked images - Print images have been deleted ERNST REINER GmbH & Co. KG...
  • Page 84 REINER-Support - Device is Switch device on deactivated - Rechargeable Charge the battery empty batteries - Rechargeable Replace the battery faulty rechargeable batteries - No rechargeable Insert the battery inserted rechargeable ERNST REINER GmbH & Co. KG...

  • Page 85: Acoustic Signals

    10 seconds 3 sound Print cartridge empty Replace print impulse cartridge 4 sound jetStamp graphic 970 not in the Put the - The display appears after impulse basis station jetStamp graphic 30 seconds of non-use in 970 in the basic...

  • Page 86: Technical Data And Accessories

    = Safety of Information Technology Equipment. = jetStamp graphic 970 is produced according to the safety standards IEC/EN 60950-1. = Do not point the jetStamp graphic 970’s nozzles towards the face of persons! Electrical and electronic waste devices Waste devices must not be disposed of in the conventional household waste. They must be returned to a special collection point for recycling of electrical and electronic devices.

  • Page 87: Technical Data

    3 × AA NiMH rechargeable battery, can be charged through enclosed mains adapter. Input: 100 – 240 VAC, 50 – 60 Hz, 0.3 A output: 5 VDC 1 A Standby time per battery approx. 72 hours charge Battery charge time approx. three hours ERNST REINER GmbH & Co. KG...

  • Page 88: Transport And Disposal

    Accessories Inkjet cartridges Order-N° P3-S-BK: 947 100 - 000 Order-N° P3-S-MG: 947 100 - 002 Inkjet cartridges MP3 (quick drying) Order-N° P3-MP3-BK: 947 100 - 120 Order-N° P3-MP5-UV: 947 100 - 140 ERNST REINER GmbH & Co. KG...

  • Page 89: Contact

    © 2015 Ernst Reiner GmbH & Co. KG All rights reserved. Translation, reprint and other reproduction of these operating instructions, even in parts and no matter the form, shall require our express written consent. We reserve the right to make content changes to these operating instructions without notice.

  • Page 90: Operating Manual

    PCset graphic Help 970 Operating Manual Operating Manual GB ERNST REINER GmbH & Co. KG...

  • Page 91: Index

    Text 53 Status displays 44 Graphic 71 - T - - I - Technical Data 87 Ink level 44 Text 53 Inserting Printing Cartridge 16 Inserting rechargeable batteries 14 Installing Software 19 Interferences 82 ERNST REINER GmbH & Co. KG...
  • Page 92 .reiner.de...

Table of Contents