Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for TRNDlabs FADER
Summary of Contents for TRNDlabs FADER
- Page 1 FADER USER GUIDE...
- Page 2 Welcome to the world of TRNDlabs products! TRNDlabs products are design focused electronics, engineered to combine ultimate performance and aesthetics. Learn how to fly! TRNDlabs Drone Academy is a video platform where www.trndlabs.com you can get your drone up and running in minutes! www.trndlabs.academy...
-
Page 3: Table Of Contents
Tips & Tricks Sensitivity Control Advanced Flight: Performing Drone Functions Functions 360º Flips Controller Functions Switching Modes Setup Charging FADER Direction Trim Troubleshooting Controller Battery Installation Rotation Trim Mobile Phone Holder Preparation Calibration Pairing Rotor Protector Installation Take-Off & Land... -
Page 4: Drone Functions
Parts Identification Functions Drone Functions Rotor Protector Drone Body Charging Cable Rotor Blade FADER Charging Port Power Switch Camera Replacement Rotor Blades (4x) Controller Functions Mobile Phone Holder Rotor Protectors (4x) Camera Light Power Light Unlock/ Land/ Take Photo/ Emergency Stop... -
Page 5: Setup
Setup Charging FADER Controller Battery Installation Open the Controller battery cover. Install 4x 1.5V AAA batteries. Slide the Controller battery cover back. Slide the battery out of the drone by pulling it gently. Mobile Phone Holder Preparation Slide the Mobile Phone Holder from closed position to open position. -
Page 6: Pairing
Piloting Pairing Place the drone on a flat and level surface. Take-Off & Land Slide the Power Switch to turn on the Controller. The Red Indicator Light on Pushing the ULES Button will cause the rotors of the drone to spin without the Controller starts flashing slowly. -
Page 7: Flight Controls
Rotation Control Flight Controls To make the drone circle to the left or the right, push the Throttle/Rotate stick cautiously to the left or right. Direction Control To fly the drone forward or backward, push the Direction stick cautiously forward or backward. To fly the drone to the left or the right, push the Direction stick cautiously to the left or the right. -
Page 8: Setup App
Enter the settings of your mobile phone and turn on the WiFi. Select “FADER-XXXX” in the list of networks. Scan the QR code to download the App: TRNDlabs FADER Go back and select the FADER App. Tap on the FLY button to enter the Live Video interface. -
Page 9: Taking A Photo
Photo & Video Back to Home Taking a Photo Tap the photo icon to take a photo. The icon will flash yellow momentarily, to Tap the back icon to return to the home screen. notify a picture is taken. You can also take a picture with the Photo Button on the controller. -
Page 10: Playing Back Videos/Viewing Photos
SD Card Tap the gallery icon to view photo and video galleries. The SD card is mounted at the bottom of FADER. You can remove the SD card and connect it to your computer via the microSD Card USB Reader. -
Page 11: Vr & Preview Mode
VR & Preview Mode Tips & Tricks Switching VR Mode ON/OFF Sensitivity Control Tap the VR Mode button to activate VR Mode. The button will turn yellow and The drone has three sensitivity settings: Low, Medium and High. A higher the live feed from the drone will be visible as split screen. - Page 12 Left Side 360° Flip Advanced Flight: Performing 360° Flips Press the Direction stick and push it to the left. Press the Direction stick to enter flip mode. The Controller will start to beep. Right Side 360° Flip Press the Direction stick and push it to the right. Push the Direction stick forward, backward, right or left to perform flips.
- Page 13 Forward 360° Flip Switching Modes Press the Direction stick and push it forward. The drone can be switched from Normal Mode to Headless Mode. Headless Mode does not require the pilot to differentiate the front (head) position of the drone, but simply use the Direction Stick for the drone to respond correctly to the given input relative to the position of the controller.
-
Page 14: Direction Trim
Troubleshooting Direction Trim Calibration The drone needs to be calibrated if it flies unstable. When hovering, if the drone flies forward or backward without moving the Direction stick, proceed as follows: Place the drone on a flat and level surface. Now, at the same time, push both the left and right joystick to the lower left corners and hold for 2 to 3 seconds. -
Page 15: Replacing Rotor Blades
Solution: Charge the battery batteries have been correctly screwdriver. inserted. as described in “Charging FADER” (page 8). Cause: The batteries do not have enough power. Problem: The drone only flies Solution: Insert new in a circle or flips over before batteries. -
Page 16: Safety Precautions
Safety Precautions Do not fly near buildings. Do not fly over stations, railways or highways. Do not Carefully follow the instructions below. Make sure you fly the drone safely, and fly near trees, or crowds of people. Do not fly in rain, snow, fog, storm, wind or you mind the warnings. - Page 17 Battery Safety Instructions • For the best performance, only use fresh 1.5V Alkaline “AAA” batteries in the controller. • Never operate the drone with low controller batteries • The drone automatically switches off if the rotors are unable to rotate. Switch the power to restart the drone.
- Page 18 WWW.TRNDLABS.COM The contents of this document are subject to change. Download the latest version from www.trndlabs.com. If you have any questions about this document, please contact TRNDlabs by sending a message to hello@trndlabs.com. © 2017 TRNDlabs. All rights reserved.
- Page 19 2693/6/EN...
Need help?
Do you have a question about the FADER and is the answer not in the manual?
Questions and answers
App not connecting to drone
The TRNDlabs FADER app may not be connecting to the drone because the WiFi network name has changed. A user reported that the network was previously called "fader" but is now a series of numbers. Even after connecting to the new WiFi network, the app repeatedly prompts to "connect drone." This suggests a connectivity issue between the app and the drone’s WiFi network.
This answer is automatically generated