Page 1
100 egg incubator (Manually hand turn eggs) Bellsouth 100 egg incubator with Automatic turner Bellsouth 100 egg incubator with Semi-Automatic turner (Hand turn eggs with push/pull rod) Made in Australia by Bellsouth Bayale Pty Ltd trading as Bellsouth...
Bayale Pty Ltd trading as Bellsouth , manufacturer and supplier of the Bellsouth egg incubator. ABN 54 895 116 137, ACN 154 912 839. Address: 5/22 Carter Way, Dandenong South VIC Australia. Bellsouth known as the “Bellsouth” in this instruction manual.
III. The Bellsouth 100 egg incubator can be purchased with an egg turner that can be plugged into power and is the Bellsouth 100 egg incubator standard model with the Automatic turner...
Do not use if egg incubator is damaged or dismantled. Do not use the egg incubator if the power cord is damaged. Contact the Bellsouth to have the cord replaced. Do not use the automatic turner with any other power pack. If the power pack is damaged do not use the egg incubator.
Page 5
Do not turn the egg incubator upside down at any time. Caution: Some reports have come to hand of erratic performance of Bellsouth incubators with solar and inverters. These have been caused by over-voltage and spurious emissions from non-sine wave inverters. Have an electrician test over-voltage and spurious !...
! Do not place egg incubator in a dusty or dirty environment. Do not move egg incubator when on and/or filled with water. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth egg incubator. ABN 54 895 116 137, ACN 154 912 839. Address: 5/22 Carter Way, Dandenong South VIC...
M A N U A L Maintenance and Cleaning To maintain the appearance and function of the Bellsouth 100 egg incubator post hatch, all chicks must be moved to a pre-warmed brooder. Unplug egg incubator and allow to cool before cleaning.
(Manual model) Contents: A Bellsouth 100 egg incubator with view port (window) and thermostat installed A thermometer and floor mounting bracket in a small box, in the bottom (base) part of the polystyrene casing near the cast moulded water channels iii.
Page 9
The bottom of the thermometer bulb will be level with, or just above, the top of the eggs. Adjust height of thermometer by bending stand. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator.
Page 10
Please note that a small quarter turn will change the temperature by several degrees so the adjustments are to be incremental. Allow at least 20 minutes between adjustments. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator.
Page 11
Refer to the Air Cell fact sheet for more on humidity. When temperature has stabilised place eggs into incubator. Place the eggs on the perforated metal floor. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator. ABN 54 895 116 137, CAN 154 912 839. Address: 5/22 Carter Way, Dandenong...
Contents: A Bellsouth 100 egg incubator with view port (window) and thermostat installed A thermometer and angle mounting bracket in a small box, in the bottom (base) part of the polystyrene casing near the cast moulded water channels iii.
Page 13
If the eggs touch both dividers at the same time they will skid and not roll over. Too many eggs in each row Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator.
Page 14
Pull more often if possible i.e. at least 3 times a day if possible. m. Use the mini funnel to fill or refill the water channels, the locator holes are marked on the base. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator.
Automatic turner Contents: A Bellsouth 100 egg incubator with view port (window) and thermostat installed A thermometer and angle mounting bracket in a small box, in the bottom (base) part of the polystyrene casing near the cast moulded water channels iii.
Page 16
For the auto turner slide the flat U shaped metal clip over the end piece, with the bottom tongue under the Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator.
Page 17
If eggs roll up over each other, place blunt ends together and pointy ends together. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator. ABN 54 895 116 137, CAN 154 912 839. Address: 5/22 Carter Way, Dandenong...
Page 18
Use the mini funnel to fill or refill the water channels, the locator holes are marked on the base. The eggs will be placed in rows between the plastic dividers. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator.
Turner won’t stop (keeps repeating Return auto turner end piece to return action) Bellsouth for repair. Bayale Pty Ltd trading as Bellsouth manufacturer and supplier of Bellsouth incubator. ABN 54 895 116 137, CAN 154 912 839. Address: 5/22 Carter Way, Dandenong...
Technical Data The Bellsouth 100 egg incubator models are designed for the hatching of avian eggs, namely poultry, waterfowl, gamefowl and exotic species. Bellsouth is registered/protected under Trademark 506215 by Bayale Pty Ltd trading as Bellsouth Bellsouth 100 Incubator Rated Voltage...
Bellsouth Incubator 100 type: This model of the Bellsouth 100 egg incubator, eggs are turned approximately 1.5 hours when turner is installed and plugged in. Black bungs are in side ventilation holes and may be removed for more ventilation. Heating element is located on underside of top of the polystyrene casing and creates heat in incubator in response to thermostat.
Page 22
Automatic turner power pack and cord to power automatic turner. Ventilation holes are on top of the polystyrene casing and where black bungs exist on sides of the Bellsouth 100 egg incubator. View port (window) on top of the polystyrene casing and allows viewing of the thermometer and indicator lamp on thermostat.
Need help?
Do you have a question about the 100 and is the answer not in the manual?
Questions and answers