7.2.3 7.3.1 7.3.2 7.3.3 7.3.4 7.4.1 7.4.2 7.4.3 7.4.4 Siemens Building Technologies Fire Safety & Security Products Safety ...7 Target readers...7 General safety precautions ...7 Transport...7 Installation ...7 Cleaning ...8 Meaning of the signal words ...8 Meaning of the hazard symbols ...8 EU directives ...9...
Page 4
7.8.2 7.9.1 7.9.2 7.9.3 7.10 7.10.1 7.10.2 7.10.3 7.10.4 7.11 7.12 Siemens Building Technologies Fire Safety & Security Products Record...37 FTP recording ...37 SD recording ...40 Emailing recording ...42 NAS recording ...45 Audio ...47 Date/Time...48 Access protection...49 Administrator ...50 User list ...50 Firewall ...51...
Page 5
Siemens Building Technologies Fire Safety & Security Products 01.2009...
Radio interference with other devices in the environment When handling modules that are susceptible to electrostatic discharge, please observe the ESD guidelines. Siemens Building Technologies Fire Safety & Security Products Qualification Activity...
IMPORTANT Meaning of the hazard symbols The nature of the hazard is indicated by icons. Tips and information Siemens Building Technologies Fire Safety & Security Products Type of risk Imminent danger of death or severe bodily injury Possible danger of death or severe bodily harm There is a risk of minor to medium injuries or damage to property.
EU directives The product complies with the requirements of the following EU directives. The EU declaration of conformity is available from: Siemens Building Technologies Fire & Security Products GmbH & Co. oHG 76181 Karlsruhe Germany European Directive 2004/108/EC “Electromagnetic Compatibility”...
Mechanism Angle control (3-AXIS) Panning range Tilting range Dimensions (L x D) Weight Siemens Building Technologies Fire Safety & Security Products Description 1/3” progressive ExviewHAD CCD, 1.3 Megapixels 1280 (H) x 960 (V) Motion JPEG/ MPEG4 SXGA: 1280 x 960 at 12.5 fps max.
SD card (2 GB) Wall plugs (4x) Mounting screw (4x) Mounting template for installation Monitor out cable *1 Siemens Building Technologies Fire Safety & Security Products Description 1/3” 1.3 MP Indoor IP Dome Colour Camera 12 V DC / 24 V AC,...
Audio in (φ3.5mm) Body casing SD Card slot Default button Microphone Front cover screw Dome cover Pan adjustment bracket Siemens Building Technologies Fire Safety & Security Products Alarm Out Alarm In Power In Audio Out Audio In Camera part definition...
IP/TV switch 5.1.7 Reset button RESET 5.1.8 Default button DEFAULT Siemens Building Technologies Fire Safety & Security Products Camera part and connector definition Alarm output port External alarm input POWER DC12V / AC24V Audio in (φ3.5mm) Video out through Ethernet...
Do not disconnect the cable by pulling on the cable. Do not drop the power adapter or subject it to strong impact. Siemens Building Technologies Fire Safety & Security Products Be sure to use only the suitable power adapter. Using a wrong power adapter may cause the camera to malfunction, heat up, or catch fire.
Connection equipment such as a hub and router suiting the network system environment and LAN cable, a Cat 5e LAN cable is recommended. Siemens Building Technologies Fire Safety & Security Products Ethernet SIEMENS...
For more information, read your user's guide for broadband router. It is also recommended to set the computer's IP address from the router's DHCP server. Siemens Building Technologies Fire Safety & Security Products Entering an IP address manually (factory default) Obtaining an IP address automatically from the DHCP server 01.2009...
Page 17
It takes about10 seconds to activate the camera. If a port number other than "80" is set, designate the port number by suffixing it after ":" as in http://192.168.0.10:88 Siemens Building Technologies Fire Safety & Security Products Connect LAN cable and turn the power on.
Using "IpFinder (Web-Cam IP Manager Version 3.0)" to Search for a Camera NOTE Set the personal computer to "Administrator authorization" when using "IpFinder." Siemens Building Technologies Fire Safety & Security Products Insert the CD in the CD-ROM drive of the personal computer.
SSDP multicast messages sent by the Web-Cam IP Manager to the network segment where the device is located. SSDP (Simple Service Discovery Protocol / network protocol) Siemens Building Technologies Fire Safety & Security Products Start the Web-Cam IP Manager by loading IP Manager.exe. This application is found on the CD included with delivery.
Enable cookies Set "Browser setting when proxy server is used" when a proxy server is used. Change "security" in Internet options as follows. Siemens Building Technologies Fire Safety & Security Products Open the Internet Explorer. Enter the default IP address: 192.168.0.10.
Page 21
● Using the network cameras via a proxy server sometimes takes a long time till images are displayed after log-in or reduces the frame rate of delivered images. Siemens Building Technologies Fire Safety & Security Products Click the "Intranet" icon if the camera to be operated is inside the intranet, clicking the "Internet"...
Page 22
Play Language PTZ operating panel Image stream 1 & stream 2 Siemens Building Technologies Fire Safety & Security Products Choose "Pop-up Blocker" on the tool menu. Choose "Always Allow Pop-ups from This Site...". this function enables OSD setting including title name, date and...
Set quality of delivered images. The size of image files (JPEG files) varies in accordance with compression ratio. Five options are available from Low to High – – – Siemens Building Technologies Fire Safety & Security Products Low compression: This setting produces highest image quality. The file size increases. Mid compression: Standard setting.
Page 24
RTSP Port Number – specify the port number you would like to use for RTSP protocol, default is 554 VIDEO Port Number - specify the port number you would like to use for video streaming, default is 5000 Siemens Building Technologies Fire Safety & Security Products 01.2009...
Page 25
2. Click RTSP then fill in web address For example: rtsp://192.168.0.194:554/livestream. Regarding default value of RTSP port, it’s based on which stream you select. VCL media player Siemens Building Technologies Fire Safety & Security Products Select Open then click the Network tab. rtsp://<IP address>:<rtsp_port>/livestream Click OK.
Page 26
Configuration Perform Quicktime For example: rtsp://192.168.0.194:554/livestream. Regarding default value of RTSP port, it’s based on which stream you select. Quicktime livestream Siemens Building Technologies Fire Safety & Security Products Select Open URL. Then fill in rtsp://<IP address>:<rtsp_port>/livestream Click OK. 01.2009...
Stream1-Stream2, cropping1-5: UPnP AUDIO output Siemens Building Technologies Fire Safety & Security Products Input your camera name here. The default name is “nwcam05”. The IP address is automatically obtained when you select ON; otherwise, select OFF to manually setup the network setting.
Max Simultaneous Connections. Press “Save” to save your setting. NOTE The purpose is to download or delete the directories/files in SD memory card. Siemens Building Technologies Fire Safety & Security Products OFF: The network Camera will stream images at the maximum frame rate allowed by the network.
Image Colour Preset image EV Adjustment Auto Gain Control Shutter Speed Siemens Building Technologies Fire Safety & Security Products Select "Image Parameters" in the Configuration menu. A sub menu for Camera Settings will appear. Click "Basic" in the sub menu.
Page 30
When OFF, rear light correction is not performed. Picture Picture Flip Picture Mirror Siemens Building Technologies Fire Safety & Security Products The Slow shutter can be turned “ON” if the sensitivity is still not so good under “High” gain condition at dark. The optimum image level can be maintained by appropriate gain and shutter combination which are determined automatically inside camera system.
Max. 8 masks can be set on the screen. The mask function is not supported when the cropping function is on. Siemens Building Technologies Fire Safety & Security Products Tick the checkbox “ON”, then click “Set Mask Zone” to start mask setting Use the mouse to drag a mask rectangle on the screen, click “OK”...
Configuration 7.3.3 Camera-Cropping settings Siemens Building Technologies Fire Safety & Security Products Tick the "ENABLE" checkbox and fill in the name, then click “Set Cropping Area” to start cropping setting. A cropping setting screen will pop-up as shown, select one type of cropping from VGA, QVGA, 4CIF, 2CIF, CIF, QCIF, and free size on bottom screen, a red-mesh rectangle will appear on the screen.
DATE/TIME on the screen. Of course, the corresponding ENABLE flag for each item shall be ”ON” to activate this function, such as camera name Enable in Network setup, Text enable in Alarm setting and Display in DATE/TIME setting. Siemens Building Technologies Fire Safety & Security Products Configuration...
Set "Audio out" for alarm message Audio alarm message can be sent to external speaker if this item set to “ON”. Siemens Building Technologies Fire Safety & Security Products The following functions will be enabled if “ Alarm Input” is set to “ON”...
Pre-recorded voice files with extension .wav that have been uploaded to SD memory card in advance can be selected as voice alarm message. Max. 4 kinds of audio source can be selected. Siemens Building Technologies Fire Safety & Security Products Set on, open motion detection function.
You can select in the appropriate menu which audio event is to be played with which event (Motion or Alarm input 1). Siemens Building Technologies Fire Safety & Security Products Event: Once alarm input1 or alarm input 2 or motion is triggered, the alarm out will be triggered immediately as well.
Scheduled Recording Determine the recording condition: STOP, all day, schedule 1 or schedule 2 from the recording schedule table for all days from Monday to Sunday. Siemens Building Technologies Fire Safety & Security Products Configuration 01.2009...
Page 38
FTP Server Settings - Server 1 and 2 Please follow your FTP setting to setup FTP server name, Login ID, Password, FTP port number, FTP mode, and FTP connecting method. Siemens Building Technologies Fire Safety & Security Products Record source: choose JPEG or MPEG4 format Record frame Set the number of images to be recorded immediately after an alarm occurs.
Page 39
SD Card Back Up if FTP Fail The network camera automatically stores images in the SD card when images cannot be recorded in the server due to a network failure, or other trouble. Siemens Building Technologies Fire Safety & Security Products Configuration...
ON: Records are overwritten beginning with old records when the capacity of the SD memory card becomes full during recording. OFF: Recording is stopped when the capacity of the SD memory card becomes full during recording. Siemens Building Technologies Fire Safety & Security Products Configure the individual settings as described below. 01.2009...
Page 41
All the other settings are same as recording by alarm as above. Recording by Network loss Select network recording. After network loss, the network camera automatically stores images based on your settings. Siemens Building Technologies Fire Safety & Security Products Record source: choose JPEG or MPEG4 format Record frame Set the number of images to be recorded immediately after an alarm occurs.
Administrator E-mail Address – input your e-mail address Click the “save & test e-mail” button to save your settings and to test your e-mail setting. Siemens Building Technologies Fire Safety & Security Products Recording cycle Set a time interval for network recording. 1, 25, 10, 30, 60, 90, 120 s can be selected.
Page 43
Attach Image – attach image files to your e-mail notification Condition settings for sending e-mail by motion Setup E-mail condition to Motion. All the other settings are similar to alarm. Siemens Building Technologies Fire Safety & Security Products Configuration 01.2009...
Page 44
Configuration Mail to Address List You can send e-mails to multiple users when schedule, alarm in, or motion detection occurred. Siemens Building Technologies Fire Safety & Security Products 01.2009...
7.5.4 NAS recording This is a method to store data on a network-based storage device. Siemens Building Technologies Fire Safety & Security Products Choose record condition: Select the condition for NAS recording: recording by Schedule, Alarm or Motion to trigger the recording session.
Page 46
All the other settings are same as recording by alarm as above. NOTE Make sure all NAS devices are ready on the network before activating this function. Siemens Building Technologies Fire Safety & Security Products Record source: choose JPEG or MPEG4 format Recording frame Set the number of images to be recorded immediately after an alarm occurs.
– Daylight Select ON to active Daylight-saving function if you are in Daylight-saving time zone (effective for NTP mode only). Siemens Building Technologies Fire Safety & Security Products Manual: Input the date and time to set up system time. NTP: You can also enable Network Time Protocol (NTP) by NTP server.
Advanced user can see the live picture and do basic operation like PTZ control, and Preset setting from buttons on bottom of screen. User can see the live picture only, no authorization to do any operation. Siemens Building Technologies Fire Safety & Security Products 01.2009...
Denied: all the IP addresses enabled in the list shall be rejected by the firewall. 7.9.2 Forbidden Ports All the ports listed and enabled will be forbidden to pass the firewall. Siemens Building Technologies Fire Safety & Security Products Configuration 01.2009...
CGI-commands. If you set ON, you always have to enter an ID and password for the web-page, but besides you can change everything using the cgi-commands. Otherwise, it’s not necessary for the login data if you choose OFF. Siemens Building Technologies Fire Safety & Security Products 01.2009...
"This will reboot the camera. Are you sure?" will be displayed. Click "OK" to reboot the network camera. Siemens Building Technologies Fire Safety & Security Products The power supply to the camera must not be interrupted during the SW update.
If a temperature notification interval has been set an e-mail notice will be delivered continuously. If the notification interval is set to "0", the e- mail notice will be delivered only once. Siemens Building Technologies Fire Safety & Security Products 01.2009...
You can click the icons on the bottom to see and process the logs, such as: “display all logs”, “display system logs”, “display user logs”…. 7.12 Notice This dialog shows all licenses information for the camera. Information Siemens Building Technologies Fire Safety & Security Products Configuration 01.2009...
It can make an alarm out event. After you finish audio record, please perform alarm audio setting. Perform audio recording in the following sequence Siemens Building Technologies Fire Safety & Security Products Execute NAS record setup first.
This application is found on the CD included in the delivery. You can update multi- network cameras synchronously. Perform firmware update in the following sequence Siemens Building Technologies Fire Safety & Security Products Execute firmware update setup first. Select filter SW version.
Maintenance Maintenance Defective modules should be sent to the nearest Siemens office to be forwarded to the service centre. Disposal All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.