Power Sentry QD MVOLT Series Installation Instructions Manual

Power Sentry QD MVOLT Series Installation Instructions Manual

Emergency fluorescent battery pack universal voltage 120 to 277vac input

Advertisement

PS 300 MVOLT, PSQ500 MVOLT, PS600 MVOLT, PS1400 MVOLT
READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO INSURE PROPER AND SAFE
FIELD INSTALLABLE FLUORESCENT BATTERY PACK IS UNIVERSALLY COMPATIBLE WITH THE BALLASTS
AND LAMP(S) AS SHOWN IN LAMP COMPATIBILITY TABLE (PAGE 5)
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
WARNING
Dual Power Supply - Risk of Shock Hazard Even
if AC Power is OFF
Disconnect polarized Test Switch / Pilot Light
connector before servicing fixture
DO NOT remove the wire harness connector
when AC Power is ON
DO NOT mount near a gas or electric heater
Battery Pack Output Voltage is 1600VDC
CAUTION
 Before wiring to power supply, turn off
Electricity at fuse panel or circuit
breaker
 All servicing shall be performed by
qualified personnel
 DO NOT attempt to service the battery.
It is not field replaceable
 DO NOT use in hazardous locations
 DO NOT use this product outdoors
DO NOT use this product in air handler
heated outlets
 DO NOT use accessory equipment not
recommended by the manufacture
 DO NOT use this equipment for other
than its intended use
Installation INSTRUCTIONS
EMERGENCY FLUORESCENT BATTERY PACK
Universal Voltage 120 to 277VAC Input
SAVE THESE INSTRUCTIONS
QD MODELS
OPERATION

IMPORTANT SAFEGUARDS

Consult your local building code for approved
wiring or installation
The emergency battery pack must be connected
to an un-switched AC power source of 120 to 277
Vac
This product is for use with indoor fixtures sealed
or unsealed
Equipment should be mounted in a location and
at heights where it will not be readily be subject to
tampering by unauthorized personnel
Make sure that the branch circuits are derived
from a common phase for both normal lighting
ballast and Battery Pack prior to installation
The Battery Pack can be switched or un-switched
(night) circuit. When used with a switched fixture,
it is important that the power to the Battery Pack
must be provided by an un-switched circuit.
Damage to the battery will occur if the Test
Switch / Pilot Light connection is made for a
prolonged period of time without AC power being
provided.
Battery packs are not field serviceable
Allow Battery Packs to charge 24 hrs before initial
and full discharge testing
Do not locate the Test Switch / Pilot Light or route
cable within 1" of fixture lamps
Emergency lighting system should be tested per
all of the required tests and as often as local
codes require or at least quarterly to insure all
components are operational.
CONTAINS NICKEL-CADMIUM
RECHARGEABLE BATTERY.
MUST BE RECYCLED OR DISPOSED
OF PROPERLY.
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QD MVOLT Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Power Sentry QD MVOLT Series

  • Page 1 INSTALLATION INSTRUCTIONS EMERGENCY FLUORESCENT BATTERY PACK QD MODELS PS 300 MVOLT, PSQ500 MVOLT, PS600 MVOLT, PS1400 MVOLT Universal Voltage 120 to 277VAC Input READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO INSURE PROPER AND SAFE OPERATION SAVE THESE INSTRUCTIONS FIELD INSTALLABLE FLUORESCENT BATTERY PACK IS UNIVERSALLY COMPATIBLE WITH THE BALLASTS AND LAMP(S) AS SHOWN IN LAMP COMPATIBILITY TABLE (PAGE 5) READ AND FOLLOW ALL IMPORTANT SAFEGUARDS...
  • Page 2 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series Battery Pack System Components Figure 1 Figure 2 Components Description Battery Pack Lamp Selector Switch   Housing (PS 1400 only) Quick Disconnect   Mounting Slots Wire Harness Plug...
  • Page 3 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series Step 3 Installation Inspection Troubleshooting Prior to operation of the Battery Pack in normal service Problem Possible Cause perform the following installation inspections. Charge Emergency Lamp 1. Wiring of the Battery...
  • Page 4 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series Lamp Selector Table (PS1400 Only) The PS1400 has a lamp selector switch that can be used to optimize the performance when placed in the “UP” position. However, based on your lamp configuration, the PS 1400 can only be placed in the “UP” position if designated in the lamp selector table.
  • Page 5 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series Lamp Compatibility Table Lamp Lamp PS300 PSQ500 PS600 PS1400 (300 Lumens) (500 Lumens) (600 Lumens) (1400 Lumens) Type Wattage 14 – 28W 2’- 4’ 24 – 54W 16 – 31W U LAMP 2’...
  • Page 6 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series Wiring Diagrams READ ALL SAFETY INSTRUCTIONS AND IMPORTANT SAFEGUARDS PRIOR TO WIRING AND INSTALLATION ONE LAMP RAPID START BALLAST BALLAST POWER CONNECTION 120 TO 277 VAC SWITCHED OR UNSWITCHED LINE –...
  • Page 7 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series THREE LAMP RAPID START BALLAST BALLAST POWER CONNECTION 120 TO 277 VAC SWITCHED OR UNSWITCHED LINE – NOTE; VERIFY VOLTAGE RATING ON LAMP BALLAST MVOLT BATTERY PACK CONNECT BLACK AND ORANGE...
  • Page 8 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series ONE FOUR-PIN COMPACT LAMP RAPID START BALLAST (PS1400 ONLY) BALLAST POWER CONNECTION 120 TO 277 VAC SWITCHED OR UNSWITCHED LINE – NOTE; VERIFY VOLTAGE RATING ON LAMP BALLAST MVOLT...
  • Page 9 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series ONE LAMP INSTANT START BALLAST BALLAST POWER CONNECTION 120 TO 277 VAC SWITCHED OR UNSWITCHED LINE – NOTE; VERIFY VOLTAGE RATING ON LAMP BALLAST MVOLT BATTERY PACK CONNECT BLACK AND ORANGE...
  • Page 10 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series THREE LAMP INSTANT START BALLAST BALLAST POWER CONNECTION 120 TO 277 VAC SWITCHED OR UNSWITCHED LINE – NOTE; VERIFY VOLTAGE RATING ON LAMP BALLAST “B” MVOLT TWO EMERG. LAMP CONNECTION...
  • Page 11 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series ONE LAMP CIRCLINE BALLAST BALLAST POWER CONNECTION 120 TO 277 VAC SWITCHED OR UNSWITCHED LINE – NOTE; VERIFY VOLTAGE RATING ON LAMP BALLAST MVOLT BATTERY PACK CONNECT BLACK AND ORANGE...
  • Page 12 Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series ONE LAMP WITHOUT AC BALLAST MVOLT BATTERY PACK CONNECT BLACK AND ORANGE LEADS TOGETHER IF ORANGE WIRE IS PRESENT 120 TO 277 VAC UNSWITCHED LINE LAMP SELECTOR (PS 1400 ONLY)

This manual is also suitable for:

Psq500 mvoltPs 300 mvoltPs600 mvoltPs1400 mvolt

Table of Contents

Save PDF