Teshow TS81B Instruction Manual

Digital PID Controller
TS81B/TS84B/TS85B/TS87B/TS89B
INSTRUCTION MANUAL
C a r e f u l l y r e a d a l l t h e i n s t r u c t i o n s i n t h i s m a n u a l . P l e a s e p l a c e
t h i s m a n u a l i n a c o n v e n i e n t l o c a t i o n f o r e a s y r e f e r e n c e .
!
W A R N I N G
An external protection device must be installed if failure of this
instrument could result in damage to the instrument, equipment
or injury to personnel
All wiring must be completed before power in turned on to prevent
electric shock, fire or damage to instrument and equipment .
This instrument must be
specifications to prevent fire or damage to instrument and
equipment.
This instrument is not intended for use in locations subject to
flammable or explosive gases.
Do not touch high-voltage connections such as power supply
terminals , etc. to avoid electric shock.
This instrument is protected from electric shock by reinforced
insulation. Provide reinforced insulation between the wire for
the input signal and the wires for instrument power supply, source
of power and loads.
This instrument is design for installation in an
instrumentation panel. All high-voltage connections such
power supply terminals must be enclosed in the instrumentati on
panel to avoid electric shock by operating personnel.
All precautions described in this manual should be taken to avoid
damage to the instrument or equipment.
All wiring must be in accordance with local codes and regulations.
Always observe precautions
Otherwise serious injury or accident may result.
Do not allow metal fragments or lead wire scraps to fall inside this
instrument. This may cause electric shock, fire or malfunction.
Firmly tighten each terminal
Otherwise electric shock or fire may result.
Do not place any obstacle around this
not to impede radiation of heat. And do not close ventilation holes.
Do not connect wires to unused terminals.
Before cleaning the instrument, always turn off the power supply.
Remove stains from this instrument using a soft, dry cloth. Do not
use a volatile solvent such as thinner in order to avoid deformation
or discoloration.
Do not rub nor strike the display unit of this instrument with a hard
object.
1. PRODUCT CHECK
TS81B
TS84B
TS85B
(1) (2) (3)
TS87B
TS89B
TS80B-E1
TS80B-E1
.
used in accordance with the
CAUTION
enclosed
described in this manual.
screw at the specified torque.
instrument in order
- -
(4) (5) (6) (7) (8)
(1) Control action
F: PID reverse action with autotuning
(2) Input type,(3) Range code: See"8.INPUT RANGE TABLE"
(4) Control output [OUT]:
M:Relay contact
8: Current(DC4 ~ 20 mA)
6: DC0-10VDC
(5) Remark:
N: No
(6) Alarm 1[AL1 for high alarm]
N: No alarm
A: Deviation high alarm
(7) Alarm 2[AL2 for low alarm]
N: No alarm
B: Deviation low alarm
(8) Power
A: 220VAC B 85-265VAC
Example
Model: TS89B
Code: FKA4-MN*AN-A
Check MODEL and CODE
is very important when ordering.
2. MOUNTING
2.1 Mounting Cautions
(1) Use this Instrument
temperature and ambient humidity.
Allowable ambient temperature: 0 to 50
Allowable ambient humidity: 45 to 85% RH
(2) Avoid the following when selecting the mounting location.
as
Rapid changes in ambient temperature which may cause condensation.
Corrosive or inflammable gases.
Direct vibration or shock to the mainframe.
Water,oil,chemicals,vapor or steam splashes.
Excessive induction noise, static electricity, magnetic fields or noise.
Direct air flow from an air conditioner.
Exposure to direct sunlight.
Excessive heat accumulation.
2.2 Dimensions
TS81B
Unit:mm
50
14.6
1
1
13.6
TS87B
Unit:mm
74
14.6
1
1
13.6
V: Voltage pulse
5: DC0-5VDC
T: Trigger (for triac driving)
See"5.5 Initial Setting
H: Process high alarm
See"5.5 Initial Setting
J: Process low alarm
D 24VDC
Specification:
Model of the controller:TS89B
Size: 96mm x 96mm
Control action: PID reverse action
Input: K type thermocouple
Out put: Relay output
Alarm: 1 deviation high alarm (AL1)
Power: AC220V
within the following ambient
C
TS84B
TS85B
Unit:mm
50
14.6
80
13.6
TS89B
Unit:mm
96
80
13.6
"
"
E 24VAC
1
1
80
14.6
1
1
80
1