Related Manuals for Realtek RTL8723BS
Summary of Contents for Realtek RTL8723BS
- Page 1 RTL8723BS Combo NGFF1216 User’s Manual Rev. 1.0 20 March 2014 Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com.tw...
- Page 2 Combo NGFF1216 User Manual COPYRIGHT © 2013 Realtek Semiconductor Corp. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of Realtek Semiconductor Corp.
- Page 3 RTL8723BS Combo NGFF1216 User Manual Table of Contents GENERAL DESCRIPTION ..............................4 1.1. RTL8723BS ..................................4 1.2................................4 NVIRONMENTAL 1.2.1. Operating ................................4 1.2.2. Storage ..................................4 1.3............................4 UNCTIONAL PECIFICATIONS 1.4..................................6 ARNING 1.4.1 Federal Communication Commission Interference Statement ..................6 1.4.2 Industry Canada Statement ............................
-
Page 4: General Description
The Realtek RTL8723BS is a highly integrated single-chip 802.11n Wireless LAN (WLAN) SDIO network interface controller with integrated Bluetooth 2.1/3/0/4.0 USB interface controller. It combines a WLAN MAC, a 1T1R capable WLAN baseband, and RF in s single chip. The RTL8723BS provides a complete solution for a high-performance integrated wireless and Bluetooth device. - Page 5 RTL8723BS Combo NGFF1216 User Manual 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 7 for HT20MHz; MCS 0 to 7 for HT40MHz 1/2/3 Mbps WiFi: CSMA/CA with ACK Media Access Control WiFi + BT: AFH, Time Division 802.11b:...
-
Page 6: Federal Communication Commission Interference Statement
RTL8723BS Combo NGFF1216 User Manual 1.4. Warning 1.4.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 7: Industry Canada Statement
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: TX2-RTL8723BS ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 8 RTL8723BS Combo NGFF1216 User Manual d'antenne requise est de 50 ohms. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà...
- Page 9 LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX IC : 6317A-RTL8723BS ". This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
- Page 10 RTL8723BS Combo NGFF1216 User Manual 1.4.3 NCC 警語 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功 率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並 改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電 機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 本模組於取得認證後將依規定於模組本體標示審合格籤。 系統廠商應於平台上標示「本產品內含射頻模組： XXXyyyLPDzzzz-x (NCC ID) 」字樣。 1.4.4 Japan Statement Host system must be labeled with "Contains MIC ID:xxxxxx“, MIC ID displayed on label Installing the Wireless NGFF1216 module Hardware Step 1.
- Page 11 RTL8723BS Combo NGFF1216 User Manual Step 3. Connect external Wi-Fi/BT antenna to corresponding RF connector. Step 4. Power on the computer. Un-installing the Wireless NGFF1216 module Hardware Step 1. Shut down the computer. Step 2. Remove external Wi-Fi/BT antenna from the wireless NGFF1216 module board.
- Page 12 RTL8723BS Combo NGFF1216 User Manual (Procedures are similar for Windows 98SE/Me/2000.) Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first. If you install the “Realtek11n Single Chip SDIO WLAN NIC Mass production kit” into your laptop computer before installing the software program from the CD.
- Page 13 RTL8723BS Combo NGFF1216 User Manual D. The system will automatically detect the card and display “Hardware Installation” screen. Click “繼續安裝” to continue. E. Please click “Finish” to complete the installation. Rev.1.0...
- Page 14 RTL8723BS Combo NGFF1216 User Manual Rev.1.0...
- Page 15 When you install Realtek11n Single Chip WLAN SDIO MINICARD Adapter, the following dialog will be shown. A. Uninstall the RTL8723BS WLAN Driver from “Start”→ “All Programs”→ “Realtek11n Single Chip WLAN SDIO NIC Mass production kit” or “Control Panel”“”→“Change or Remove Programs”.
- Page 16 RTL8723BS Combo NGFF1216 User Manual Installing the Bluetooth Module Software A. Connect the USB-to-RS232 adapter to computer. B. Choose the right COM port and baud rate setting from the BT test UI, then press the OK button below. Rev.1.0...
- Page 17 RTL8723BS Combo NGFF1216 User Manual C. The driver will be installed successfully as shown below. Realtek Semiconductor Corp. Headquarters No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu, 300, Taiwan, R.O.C. Tel: 886-3-5780211 Fax: 886-3-5776047 www.realtek.com.tw Rev.1.0...
Need help?
Do you have a question about the RTL8723BS and is the answer not in the manual?
Questions and answers