Page 1
CONTROL Caution : The part marked with is generating a high Voltage, so care will be necessary when working. MUTE/SETUP OPEN/CLOSE SLIDE CONTROL MOBILE MULTIMEDIA STATION 45Wx4 TUNE/A.ME MODE TO ALPINE (CVA-1004R) Home Page 3 / 03-A 68E35501S01 CVA-1004R /CVA-1004RR...
Page 2
<Cautions for Safe Repair Work> The following cautions will prevent accidents in the workplace and will ensure safe products. *The symbols indicate caution is needed to prevent injuries and damage to property. The symbols and their meanings follow. If you ignore this symbol and handle the product incorrectly or unsafely, Warning serious injury or death may result.
Page 3
Contents Packing Assembly Parts List Packing Method View System Connections Specifications Extension Cable Specification Explanation Adjustment Procedures How to use JIG for the LPS Adjustment Block Diagram Parts Layout on P.W.Boards and Wiring Diagram Schematic Diagram Terminal Voltage of IC/TR Description of IC Terminal Exploded View (Cabinet) Attention in Assembling...
Page 4
Packing Assembly Parts List Symbol Part No. Description Symbol Part No. Description 15B03202K01 CARRING,BAG 01E35519S01 ASS'Y WIRE PWR 07B03203K01 BKT,STOPPER ASS'Y 03A31982Y01 SCR M4X5 FLAT 33C03201K01 FACE,PLATE 15D03200K01 CASE,INNER 68P02294K66 OWNERS MANUAL(RO/RR) 03E27739S01 BOLT HEX M5(A) 75E28553S01 CAP RUBBER Packing Method View TO CONTENTS...
System Connections <Basic Connections> Antenna ISO Antenna Plug REMOTE OUT To remote input lead (White/Brown) NORM EQ/DIV AUDIO INTERRUPT IN (Pink/Black) To vehicle phone REMOTE TURN-ON (Blue/White) To amplifier or equalizer PARKING BRAKE (Yellow/Blue) To the parking brake signal lead ILLUMINATION (Orange) To the instrument cluster illumination...
Page 6
This lead may be connected to the vehicle's instrument Black) cluster illumination lead. This will allow the Right Front (+) Speaker Output Lead (Grey) backlighting of the CVA-1004R/CVA-1004RR to dim Right Rear (–) Speaker Output Lead (Violet/ whenever the vehicle's lights are turned on. Black)
Page 7
<System Example 1: Refer also to Basic Connections.> Speakers Rear or Amplifier Subwoofer (NVE-N077P) Navigation System (Sold Separatel y) NORM EQ/DIV (Yellow) (Yellow) (White) DVD Video Player (Sold Separately) (Red) REMOTE IN REMOTE OUT (White/Brown) (White/Brown) CD Changer (Ai-NET) (Sold Separately) * When Subwoofer is set to OFF: Output is from Rear speakers.
Page 8
When connecting with NVE-N055PS of the Alpine's Navigation System To Video output terminal (NVE-N055PS) VIDEO IN CVA-1004R/ Connector Box Navigation CVA-1004RR GUIDE IN RGB Converter Cable To Guide output terminal REMOTE IN REMOTE OUT KCE-030N (Sold Separately) (White/Brown) (White/Brown) RCA Extension Cable...
Page 9
<System Example 2 (connecting to the optional KCE-104V): Refer also to Basic Connections.> CD Changer (Ai-NET) (Sold Separately) REMOTE IN REMOTE OUT (White/Brown) (White/Brown) REAR SEL 1 (Yellow) (Grey/Pink) DVD Video Player (White: L-ch) REAR SEL 2 (Sold Separately) (Black/Pink) (Red: R-ch) (DVA-5205/DHA-S680 series) IGNITION...
Page 10
Connect this lead to a good chassis ground on the vehicle. System Make sure the connection is made to bare metal and is Connect to the RGB Input Terminal of the CVA-1004R securely fastened using the sheet metal screw provided. /CVA-1004RR Fuse Holder (7.5A)
Specifications <Monitor SECTION> Screen Size ..............................6.5-type Display System ........................Transparent type TN LCD Drive System ........................... TFT active matrix Number of Picture Elements .................... 280,800 pcs. (1,200 x 234) Light Source ....................U-shaped cold cathode fluorescent tube <Tuner SECTION - FM RADIO> Intermediate Frequency .........................
Page 12
<GENERAL> Signal System ............................PAL System Power Supply ......................DC14.4V (11 to 16V allowable) Power Output (Ref. CD 1kHz, 0dB (TCD-782, No.2), T.H.D. 10%) /Impedance ........18W/ch/4ohm Pre Output (Ref. CD 1kHz, 0dB (TCD-782, No.2), T.H.D. 1%) /Impedance ....REAR : 2V±2.5dBV/ch/10kohm Back-up Current (ACC OFF 30Sec.
Page 13
Extension Cable * When repairing or measuring the voltage of this unit, connect with the Extension Cable as shown in below. TUNER P.W.Board MAIN P.W.Board 01V28083S01 FRONT P.W.Board TO CONTENTS...
Page 14
Specification Explanation 1. Cancellation of AUX Regulation (Parking Wire) (1) HAND : L 2. Soft Version (Check Sum) Push "SOURCE/PWR" Key and "F5" Key at the same time. 3. Elimination of EEP-ROM Memory After pushing "SOURCE/PWR" Key and "CHG/R.SEL" Key at the same time, push "PLAY/PAUSE/TUNE/A.ME" more than 3 seconds, and confirm by ACC OFF/ON.
For 50 ohm FM Signal Generator Figure 1 (2) Connection DC Volt Meter Antenna Receptacle TP504 FM Dummy TP502 Antenna CVA-1004R/ FM Signal Generator Figure 2 CVA-1004RR * only short-circuit at adjustment (3) Control Settings Fader Control ........Center Position Bass Control ........Center Position Balance Control ........
Page 16
Figure 4 (Mod. OFF, 216KHz Adjustment TP504 TP502. MONO, 30%) (4-A) (SPEC) TP504 : 1.0±0.05V 2. VIDEO Adjustment (1) Connection Frequency Counter CVA-1004R/ CVA-1004RR TP813 VGND(TP7050) MAIN P.W.Board LCD P.W.Board Figure 5 DC Volt Meter CVA-1004R/ CVA-1004RR TP7053 VGND(TP7050) LCD P.W.Board...
Page 17
Frequency Counter Oscilloscope CVA-1004R/ CVA-1004RR TP7046 VGND(TP7050) LCD P.W.Board Figure 8 Oscilloscope CVA-1004R/ CVA-1004RR TP7056 AUX IN VGND (TP7050) LCD P.W.Board Pattern Generator Figure 9 (10STEP Signal) Oscilloscope CVA-1004R/ CVA-1004RR TP7015 AUX IN VGND (TP7050) LCD P.W.Board Pattern Generator Figure 10...
Page 18
(2) Adjustment Procedures * PAL Adjustment Test Point/ Step Operations Process Connection P.W.Board Adjustment Coordinates Confirm AUX terminal OPEN. Figure 5 to 8 TP813 (4-F) Adjust by VR803 so that it may be set to 119 to PWM Frequency Adjustment Figure 5 TP7050 120KHz.
Page 19
Test Point/ Step Operations Process Connection P.W.Board Adjustment Coordinates After finishing PAL Adjustment, change to COLOR BAR Signal. Adjust by L706 so that blue level of TP7014 TP7014 waveform may become the same as black level (5-C) of TP7014 Waveform. RED Waveform-2 Adjustment Figure 11 TP7050...
Page 21
How to use jig for the LPS Adjustment (01V32359S01) Outline Our JIG is JIG which makes Mechanism Block move to adjust the voltage of LPS for TILT of in-dash monitor such as “CVA-1004RCVA-1004RR”. It is adjusted with measuring an output voltage from LPS and confirming the voltage. (This adjustment surely becomes necessary when MONITOR and Mechanism Block are left.) Connection Figure Multi Meter...
Page 22
Figure-1 SW1 is pushed down on the A side, and Display is made horizontal. (It is made the condition like the Figure.) The figure which saw SW from the top Multi Meter Power Supply It is made horizontal. Figure-2 Volume under GEAR, LPS ASSY is turned, and the voltage of the Multi Meter adjusts it to 0.10+0.10, -0.10V (the voltage of MONITOR horizontal position).
Block Diagram TO CONTENTS MULTI CHIP UNIT Ai AUDIO Ai DIN MUTE E2PROM ELE VOL TUNER FRONT (M24C01) (TDA7412) (TDA7511) REAR MUTE NAVI AUDIO POWER CONN BUS I/F FRONT DECODER REAR Power-IC BATT Reg. Motor Reg. Motor Driver (+8.3V) MAIN u-COM REM/ &...
Page 45
(ESC P.W.Board) IC401 Q401 (TOP P.W.Board) IC451 IC452 Q451 Q452 Q457 Q458 [Measuring Conditions] 1. Power Supply : DC14.4V 2.5 / 0 2. Measuring Meter : Digital Multi Meter 2.3 / 14 DIMMER OFF/ON 3. Measuring Point Reference : Between GND 4.
Page 46
Description of IC Terminal D70F3089YGJ : IC501 Symbol Terminal Description SSTOP FM station detection signal input terminal. Adjoining rejection detected input terminal. MULTIPATH Multipath signal input terminal from RDS Decoder. PAUSE Pause signal input terminal from RDS Decoder. GND connect terminal. GUIDE CONT Voice guidance control signal input terminal from NAVI.
Page 47
Symbol Terminal Description I/F-SCL(SCK0) Serial Clock output terminal for external BOX. (connected writng writer SCK) Compulsion Stand-by detected input terminal. BDET (BATT voltage : less than 7.65 to 8.93V) BUS-IN(RXD0) Ai-NET BUS Data signal input terminal. (connected TxD at writing writer UART) BUS-OUT(TXD0) Ai-NET BUS Data signal output terminal.
Page 48
Symbol Terminal Description LOAD-MTR2 Motor Driver driving signal-2 output terminal for horizontal movement adjustment. TILT-MTR1 Motor Driver driving signal-1 output terminal for TILT angle adjustment. TILT-MTR2 Motor Driver driving signal-2 output terminal for TILT angle adjustment. GND connect terminal. OSD-SCL Serial Clock output terminal for OSD communication.
Page 49
Symbol Terminal Description DF-KEY2 KEY-2 input terminal of DF Block. S-METER FM/AM field strength (DC voltage) input terminal. ADJ-DET Adjoining rejection detection signal (DC voltage) input terminal. VDD+5V connect terminal. (for LPS control at auto Close) GND connect terminal. TO SCHEMATIC TO CONTENTS...
Page 50
8 X2 Exploded View (Cabinet) (1/2) ET202 (Back Side) ET200 LCD7001 ET302 (Back Side) CB801 ANT101 CH401 CB502 SW401 LCD401 ..point of GREASE applied. GREASE, E-PAST ( 11S42419J09 ) TO PARTS LIST TO CONTENTS GREASE, G PASTE ( 11S42419J19 )
Page 51
Exploded View (Cabinet) (2/2) 125 X2 M5904 (Back Side) 118 X2 M5906 M5905 (Back Side) (Back Side) 1( 301 Front Side View) ..point of GREASE applied. 125 X2 GREASE, E-PAST ( 11S42419J09 ) GREASE SILICON ( 11S490487 ) GREASE, G PASTE ( 11S42419J19 ) GREASE, G-8007 ( 11S41558Y01 ) TO PARTS LIST TO CONTENTS...
Page 52
Attention in Assembling (GEAR MONITOR) <The figure seen from the "a" direction / a-a' Cross section / spring side> It engages a gear, and it is located. • COVER TOP GEAR is fitted to GEAR MONITOR as the figure. (COVER TOP GEAR) Position to pass a spring TO CONTENTS...
Need help?
Do you have a question about the CVA-1004R and is the answer not in the manual?
Questions and answers