Related Manuals for Vanco Evolution EVO-IP
Summary of Contents for Vanco Evolution EVO-IP
- Page 1 EVO-IP HDMI® OVER IP Quick Start Guide Vanco Part Numbers: EVOIPTX1 Transmitter EVOIPRX1 Receiver EVOIPCTL1 Control Box www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 INTRODUCTION The Evolution by Vanco EVO-IP HDMI over IP is a complete audio, video, and control product over ethernet system. As a whole, the system has the ability to send up to 1064 sources to 1064 displays along with IR and RS-232 pass-through, analog and digital audio breakouts on the send and receive ends, video up to 4K@60Hz and HDR10/Dolby Vision compatibility, with POE up to 330ft/100m when connected to a POE enabled switch off of a single Cat6 cable.
-
Page 4: Specifications
SPECIFICATIONS TECHNICAL SPECS - Transmitter and Receiver HDMI Compliance ............HDMI HDCP Compliance ............Yes Video Resolution ............4K@60Hz, 4:4:4; 4K@60Hz, 4:2:0 HDR10; 4K@30Hz, 4:4:4 HDR10; 4K@30Hz, 4:2:2 HDR10 and Dolby Vision; 4K@24Hz, 4:4:4 HDR10 and Dolby Vision Latency ..............2 frames (33ms) maximum HDMI over UTP transmission [24-bit] ...... -
Page 5: Package Contents
SPECIFICATIONS TECHNICAL SPECS - Control Box Role of Usage ............Smart Controller Input ................ 1 x RJ-45 Output ..............1 X HDMI HDMI Connector ............Type A [19-pin female] RJ-45 Connector ............WE/SS 8P8C USB (Female) ............Reserved for future use MECHANICAL SPECS - Control Box Housing .............. -
Page 6: Panel Descriptions
PANEL DESCRIPTIONS Transmitting Unit 1. Link Indicator Light (lights up when connected and transmitting signal to ethernet switch) 2. Power Indicator Light (lights up when powered up by PoE or included power supply) 3. Info Indicator Light (shows data is being sent/received over the Cat cable/RJ45 port) 4. - Page 7 PANEL DESCRIPTIONS Receiving Unit 1. Link Indicator Light (lights up when connected and receiving signal from ethernet switch) 2. Power Indicator Light (lights up when powered up by PoE or included power supply) 3. Info Indicator Light (shows data is being sent/received over the Cat cable/RJ45 port) 4.
-
Page 8: Connection Diagram
PANEL DESCRIPTIONS Control Box 1. 5V Power Port (necessary as this unit requires external power) 2. Status Indicator Light (lights up when communicating with the system) 3. Power Indicator Light (lights up when powered up by included power supply) 4. HDMI OUT (connect to local display to show system IP information) 5. -
Page 9: Connect And Operate
Cat5e/6. Ensure there is 1 transmitter being used for every source/input and 1 receiver being used for every display/output in the system. Note: Vanco recommends using Cat6 for any 4K applications and to use one of the ethernet switches recommended on the product webpage found at www.vanco1.com. - Page 10 Type in the username and password for the system Installer: Username and password is admin (full access to settings) User: Username and password is user (limited access to settings) Go to the SETUP tab to further customize the name and ID for each device www.vanco1.com...
-
Page 11: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...
Need help?
Do you have a question about the Evolution EVO-IP and is the answer not in the manual?
Questions and answers