SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
Before carrying out any maintenance, disconnect the appliance • from the power supply. Ensure that the appliance is switched off before replacing the • lamp to avoid the possibility of electric shock. Do not use a steam cleaner to clean the appliance. •...
• Use only correct isolation devices: line • Do not put flammable products or items that are protecting cut-outs, fuses (screw type fuses wet with flammable products in, near or on the removed from the holder), earth leakage trips appliance. and contactors.
• If you use an oven spray, follow the safety • Use original spare parts only. instruction on it's packaging. DISPOSAL • Do not clean the catalytic enamel (if applicable) with any kind of detergent. WARNING! Risk of injury or suffocation.
PREHEATING burner area, as shown in "Product description" chapter. Preheat the empty appliance before first use. 1. Set the maximum temperature. INITIAL CLEANING 2. Let the appliance operate for 1 hour. Remove all accessories and removable shelf 3. Set the function supports from the oven.
OVEN FUNCTIONS Oven function Application The oven is off. Off position To turn on the lamp without a cooking function. Light To roast larger pieces of meat on the turnspit. Turnspit USING THE GRILL 2. Release the knob for the gas control. Do not keep the knob for the gas control pushed Oven safety device: for more than 15 seconds.
A. Turnspit frame B. Forks C. Spit D. Handle 1. Put the turnspit handle into the spit. 2. Put the deep pan on the lowest shelf position. 3. Put the spit frame on the third shelf position from the bottom. Baking tray: Push the baking tray between the guide bars of the shelf support.
ADDITIONAL FUNCTIONS COOLING FAN If you turn off the oven, the cooling fan can continues to operate until the oven cools down. When the oven operates, the cooling fan turns on automatically to keep the surfaces of the oven cool. HINTS AND TIPS Initially, monitor the performance when you cook.
GAS OVEN COOKING Meat & Poultry Temperature Food Time (min) Preheat the empty oven for 10 minutes before (°C) cooking. Use the wire shelf. Goat meat, 1.8 170 - 180 60 - 90 Put a deep pan on the second shelf position. Use the third shelf position.
Page 11
Tempera- Tempera- Food Time (min) Food Time (min) ture (°C) ture (°C) Fruit pie in a 26 cm min. 50 - 60 Ginger bread min. 45 - 55 round cake mould on the wire shelf Bread Preheat the empty oven for 10 minutes before Choux pastry 35 - 45 cooking.
Use the turnspit with the bottom oven burner. Use the third shelf position. Time (min) Food Pieces Tempera- Food Time (min) ture (°C) 1st side 2nd side Poultry, 1.0 - 1.2 kg 190 - 75 - 85 Toasted 4 - 6 5 - 7 sandwiches Roasts, 0.8 - 1.0 kg...
Temper- Accesso- Shelf Food Function ature Time (min) Comments ries position (°C) Beef Grilling Wire max. 20 - 30 Put the wire shelf burger shelf on the fourth level 6 pieces, and the dripping 0.6 kg drip- pan on the third ping level of the oven.
REMOVING AND INSTALLING DOOR The oven door has two glass panels. You can remove the oven door and the internal glass panel to clean it. Read the whole "Removing and installing door" instruction before you remove the glass panels. The oven door may close if you try to remove the internal glass panel before you remove the oven door.
2. Disconnect the oven from the mains. 3. Put a cloth on the bottom of the cavity. CAUTION! Always hold the halogen lamp with a cloth to prevent grease residue from burning on the lamp. The back lamp REPLACING THE LAMP 1.
Problem Possible cause Remedy The turnspit does not rotate. The turnspit is not correctly in- Refer to "Using the accesso- stalled into the turnspit hole. ries" chapter, Using the turn- spit. SERVICE DATA the oven cavity. Do not remove the rating plate from the oven cavity.
OVEN INJECTOR REPLACEMENT 3. Seal the connection correctly. Use a leak detection to control it. 1. Remove the bottom plate of the oven cavity (A) to get access to the oven burner (B). ADJUSTMENT TO DIFFERENT TYPES OF GAS Only a qualified technician is authorized to handle adjustment of different types of gas.
5. Release the burner injector (D) with a 7 mm From liquid gas to Release the adjust- socket spanner and replace it with a different natural gas ment screw ap- one, which is necessary for the type of gas you proximately 1/3 of use.
Page 19
min. 4mm min. 550 min. 560 65cm² 130cm² ±1 min. 550 min. 560 ±1 65cm² 130cm² There must be a clearance of minimum 4 mm There must be a continuous air supply around the between the top surface of the appliance and the oven in order to not have the oven become too hot.
When you install a hob above the oven, make This appliance is supplied only with a main cable. different electrical connections for the hob and for CABLE the oven. Only make connections with correct cables for the Cable types applicable for installation or power supplied.
GAS OVEN BURNER NOMINAL NOMINAL BY-PASS INJECTOR Reduced gas Gas type GAS POWER GAS FLOW NEEDLE MARK (1/100 power (kW) (kW) (g/h) (1/100 mm) G20 (2H) 20 mbar Reg. G30/G31 30/30 mbar GAS GRILL BURNER NOMINAL NOMINAL BY-PASS INJECTOR Reduced gas Gas type GAS POWER GAS FLOW...