Grundig GDK-2774-BXB Service Manual
  1. Manuals
  2. Brands
  3. Grundig Manuals
  4. Ventilation Hood
  5. GDK-2774-BXB
  6. Service manual

Grundig GDK-2774-BXB Service Manual

Beko-2014-better t- type hood
Hide thumbs
Table of Contents

Advertisement

Quick Links

BEKO-2014-BETTER
T- TYPE HOOD
SERVICE MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GDK-2774-BXB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Grundig GDK-2774-BXB

Summary of Contents for Grundig GDK-2774-BXB

  • Page 1 BEKO-2014-BETTER T- TYPE HOOD SERVICE MANUAL...

  • Page 2: Table Of Contents

    1.COVER 2.CONTENT 1.COVER ............................2 2.SAFETY WARNINGS ........................4 2.1 G ..........................4 ENERAL SAFETY 2.2. INSTALLATION FOR SAFETY ......................5 2.3 INFORMATION TO BE PROVIDED TO CONSUMERS ............... 5 3. TECHNICAL SPECIFICATIONS ..................... 7 4.PRODUCT INSTALLATION / ASSEMBLY RULES / SETTINGS ............8 4.1 P .........................
  • Page 3 12.7 M ....................38 AINS EPLACEMENT OODS 12.8 I ......................40 NSTALLİNG A CARBON FILTER...

  • Page 4: Safety Warnings

    2.Safety Warnıngs Thank you for purchasing this Grundig product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use.

  • Page 5: Installation For Safety

    Electrical safety • To get your product ready for use, firstly you must have installation place and electric wiring prepared. Later, you may call Authorised Service nearest to you. • If it has a failure, the product should not be operated without being repaired by the Authorised Service Agent.
  • Page 6 • pots and pans , etc. placed on top of hobs . After placing the product run. Otherwise, the rising heat can deform some parts of your product . • Do not create a high flame under the product . Otherwise , holding oils grease filters can cause a fire .

  • Page 7: Technical Specifications

    3. TECHNICAL SPECIFICATIONS External dimensions (height/width/depth) min.735 mm max. 1130 mm/600 mm/502 mm Voltage/frequency 220-240 V ; 50 Hz Control 3 seviye Suction power 620 m Motor power consumption 150KW Lamp power consumption 25KW Total power consumption Max 221 W Fuse min.

  • Page 8: Product Installation / Assembly Rules / Settings

    HOOD 4.PRODUCT INSTALLATION / ASSEMBLY RULES / SETTINGS 4.1 Product transport Product should be carried by two person for safety of the product and ergonomics While downloading the product from transport vehicles, do not leave the ground hardly , drag on the ground and scroll down the stairs.
  • Page 9 HOOD Chimney is avaible in the carton box seperated another carton Grasp with both arms and remove hood from inside the box. Unpack hood. Remove the left and right styrofoam.
  • Page 10 HOOD Finally styrofoam which on the hood taken. And the meanings of the symbols on product packaging; Do not carry Carry the product Carry with Preserve the product in this way by Do not step on Fragile barrow in from damp like in the squeezing with the product.

  • Page 11: Controlling The Setup Place And Energy Sources

    HOOD 4.3 Controlling the setup place and energy sources 4.3.1 Measurement control of the mounting place min. Refer to the nearest Authorised Service Agent for installation of the product. Make sure that the electric installations are in place before calling the Authorised Service Agent to have the product ready for operation.
  • Page 12 HOOD Please apply the following steps for the hood's installation min. max. 1. Centering the cooking appliance, draw an axis line on the wall up to 950mm height. Later, draw two parallel lines at 90mm distance on both sides of the axis line reaching to the ceiling.
  • Page 13 HOOD 3. As shown in Figure 2, fix connectors (C) to the holes X1 and X2 via two fixing screws supplied with the accessories. Screw distance ring (D) on the Y hole as small-diameter side facing the wall. 4. nstall the hood from the key hole on back plate onto the distance ring and pull downward to make sure that it is secured.

  • Page 14: For Chimney Connection Usage

    HOOD 5. For chimney connection usage: In chimney-connected position, absorbed air will go through oil filters to the outlet and then will reach to the chimney though connection pipes and finally thrown out from the chimney. When using this connection position, 150mm to 120 mm E connector should be installed on chimney outlet flange as shown in Figure 5.
  • Page 15 HOOD Place ear slots of carbon filters (L) to the ears on motor carrier (M) as shown in Figure 7 and turn anti-clockwise to fix in place. Apply the same procedure for the motor carrier on the other side. NOTE: Failure to clean and service oil filters periodically and failure to replace carbon filters at the end of service life (approximately 4 months) may have the risk of causing fire.
  • Page 16 HOOD To install lower chimney B, stretch the chimney by pulling slightly from both sides and secure it onto upper chimney's slots as shown in Figure 9. You may use the hood in two ways: 1- Chimney-connected use The steam is thrown out via chimney pipe which is secured to the connection ring on the hood.
  • Page 17 HOOD • Tighten by turning it to right and left as shown in the figure. • Re-install aluminum filters. 5.3.2 Control of electrical installations Products in the control of electrical installations should be considered the following values associated with the product. External dimensions (height/width/depth) min.735 mm max.
  • Page 18 HOOD Select the programme you want to measure the hood. (1.step/2. step /3. step update) Install the product’s plug to wattmeter and install wattmeter’s plug to wall plug...
  • Page 19 HOOD The network supply data, should be same as product type label’s data. Type label located to inside the product, at the next to the fan engine After the product installation, the plug must be at easily accessible location. Check electrical functions.

  • Page 20: Product Use

    HOOD 6. Product Use The hoods have a motor with various speed settings. For a good performance, low speed is recommended in normal conditions and high speed for heavy smell and steam conditions. 1-Open-Close / Hz1 2-Speed 2 3-Speed 3 /Booster 4- Function knob 5- Lamp Button 6.1 Starting the Hood...

  • Page 21: Closing The Hood

    HOOD To change the speed level, press the speed2 and Speed3 button. NOTE: Do not press more than two buttons at the same time. If pressed, higher speed will be activated. 6.2 Closing the Hood The hood is running at a certain speed, press the Power button.
  • Page 22 HOOD NOTE: Off button does not turn off the lamp, only stopping the hood. Intensive ventilation mode (Booster) Opening Press speed 3 button and hold on more than 2 seconds. Intensive ventilation mode is activated and a maximum of 10 minutes work. Continues to work in the speed3 position will active at the end of 10 minutes.
  • Page 23 HOOD Automatic shut-off mode While the roduct running a certain level press F button and hold for more than 2 seconds Automatic shut-off mode is activated and level warning light flashes in the color set that level. The product automatically turns off after 20 minutes at the set level .

  • Page 24: Products Used In The Labels

    HOOD 7. PRODUCTS USED IN THE LABELS 7.2 Products used tags and descriptıons 7.2.1 Type of Label It contains some information about the product. Type tag location; Type of products, type label located to next to engine. You should remove product filter for find the type label.

  • Page 25: Barcode Label

    HOOD 7.2.2 Barcode Label Barcode label includes many lines and spaces which represent producer country, brand and feature of model. Location of barcode label; This label bonded at product packing’s carton. 7.3.3 Enercy Label; There is no energy in the product.

  • Page 26: General Working Principle

    HOOD 8. GENERAL WORKING PRINCIPLE Hoods in the control panel is controlled by 5 buttons. One of them is the lamp on / off button. The other 4 buttons for motor control. There are 3 leves in the hood, there is a one button for controlling each level and on/off button..

  • Page 27: List Of Component/Component Operation Principles

    HOOD 9.LIST OF COMPONENT/COMPONENT OPERATION PRINCIPLES 9.1 Oven Lamp The lamp controled by cummutotor is connected to the control button or with the help of a special button. 9.2 Carbon filter Air is filtered through the carbon filter and is sent back into the room again.

  • Page 28: Better Mainboard

    HOOD 9.4 Better Mainboard The center hosts and apply on all processing units. 9.5 Carbon Filter Air is filtered through the carbon filter and is sent back into the room again. carbon filter to be mounted chimney or flue pipe .Carbon filter is used in this cases: where chimney not the suitable at home.

  • Page 29: Flow Fault/Fault Detection Diagrams

    HOOD 10. FLOW FAULT/FAULT DETECTION DIAGRAMS...

  • Page 30: Component Assembly/Disassembly Of The Equipment To Be Used In

    HOOD 11. Component Assembly/Disassembly of the equipment to be used in. Cordless screwdriver...

  • Page 31: Component Assembly/Disassembly

    HOOD 12.Component Assembly/Dısassembly NOTE: Dismantling of components are described below. Please sign in assembling components from the reverse. Hoods Chimney Top Sheet Replacement 1. Chimney top sheet’s right and left located a screw unscrewed by screwdriver You can change unassembled chimney sheet Chimney of Hoods Replacement To change chimney ,firstly hood’s upper sheet must be removed By lifting upward chimney hoods can replace it with a new one.
  • Page 32 HOOD You can change the filter with a new one. Hoods Replacement Lamp Lamp light pressing, turned clockwise direction. Replace the lamp with a new one. 32/TR...

  • Page 33: Hood Replacement Lamp Sheet

    HOOD 12.1 Hood Replacement Lamp Sheet Hoods Lamp Sheet Replacement Hoods lamp plate connected to the main body with 2 screws on the lamp. Remove the screws to for replace the lamps sheet. Before removing the lamp lights remove sheet. Idle lamp sheet can replace it with a new sheet.
  • Page 34 HOOD When removing the screws prevent the fall of the engine , seen in the picture. 5.After dismantling the screw slowly wasted away through the hood the engine can replace it with new. 34/TR...

  • Page 35: Changing The Hour Intervals Tires

    HOOD 12.3 Changing the hour intervals Plastic Sheet and plastic bound with 2 screws. Remove the screw with the star screwdriver. 35/TR...

  • Page 36: Replacing The Motherboard Hoods

    HOOD 12.4 Replacing the motherboard Hoods Hood motherboard is attached to the chassis with 2 screws. Remove the screws with a screwdriver help. 36/TR...

  • Page 37: Changing Keys

    HOOD Remove the cover after the disassembly. Remove the cable connections Remove the screws with a screwdriver help. Replace the card with a new one. 12.5 Changing Keys Push the button to the right to push the nail outside inward. 37/TR...

  • Page 38: Motor Replacement Card

    HOOD Replace with a new button. 12.6 Motor Replacement Card Motor card is connected to the chassis with 2 screws .. Disconnect the cables on the card, respectively. After disassembly, replace with a new one. 12.7 Hoods Supply Cord Replacement Hoods supply cord as shown in the picture is attached with 2 screws.
  • Page 39 HOOD Unscrew the screws with a screwdriver supply cord holder can change. Hood cord plug from the mains plug holes spend your interests. 39/TR...
  • Page 40 HOOD 12.8 Installing a carbon filter The carbon filter is installed to slots are shown in the picture. Place the carbon filter to the slots. 40 | TR...
  • Page 41 HOOD Place on either side of the slot. You can use a carbon filter. After the installation process is finished aluminum filter insert again. NOTE: Can be supplied from stock numbers in the order given by Carbon Filter of service to customer demands.
  • Page 43 REVISION DATE EXPLATION NAME YALÇIN KUM 05.03.2015 T-TYPE HOOD SERVICE MANUAL $(in) $(id) $(pn)
  • Page 44 Envelope IV...

Table of Contents