Panasonic TH-103PF12E Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Monitor
  5. TH-103PF12E
  6. Service manual
Panasonic TH-103PF12E Service Manual

Panasonic TH-103PF12E Service Manual

Gpf12d chassis
Hide thumbs Also See for TH-103PF12E:
Table of Contents

Advertisement

Quick Links

Download this manual
Service Manual
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.

TABLE OF CONTENTS

1 Safety P recautions-------------------------------------------------------- 3
1.1. General G uidelines------------------------------------------------ 3
1.2. Touch-Current C heck---------------------------------------------3
2 W arn ing ------------------------------------------------------------------------- 4
2.2. About lead free solder (PbF)---------------------------------- 5
3 S ervice N avigation -------------------------------------------------------- 6
3.1. Service H in t---------------------------------------------------------- 6
3.2. Applicable s ig n a ls ------------------------------------------------- 8
4 S p ec ifica tio n s--------------------------------------------------------------- 9
5 Operating Instructions-------------------------------------------------10
6 Service M o d e -------------------------------------------------------------- 12
6.1. CAT (Computer Aided Test) m o d e ----------------------- 12
7 Troubleshooting G uid e----------------------------------------------- 17
7.1. Self C heck----------------------------------------------------------- 17
7.2. No Power ------------------------------------------------------------ 19
Panasonic
WARNING
A
PAGE
■
®
High Definition Plasma Display
TH-103PF12E
Model No.
G PF12D Chassis
7.3. No Picture------------------------------------------------------------19
7.4. Local screen failure--------------------------------------------- 20
8 Service Fixture & T o o ls ----------------------------------------------- 21
8.1. SC jig -------------------------------------------------------------------21
9.1. Rear Cover and Board-----------------------------------------22
9.3. Removal of Side Angle (L), (R )--------------------------- 25
9.4. Removal of H D E -B oa rd------------------------------------- 26
9.5. Removal of H L-B oard-----------------------------------------27
9.6. Removal of H 5-B oard-----------------------------------------27
9.7. Removal of D S -B o a rd ----------------------------------------27
9.8. Removal of HX-Board-----------------------------------------28
9.9. Removal of D N -B o a rd ----------------------------------------28
9.10. Removal of P B-Board----------------------------------------- 29
9.11. Removal of D-Board------------------------------------------- 29
9.12. Removal of P-Board (M A IN _1 )--------------------------- 29
9.13. Removal of P-Board (M A IN _2)--------------------------- 30
9.14. Removal of P-Board (SUB)---------------------------------30
© P anasonic C orporation 2009
Unauthorized copying and distribution is a violation
o f law.
Order Number PCZ0912156CE
PAGE

Advertisement

Table of Contents
loading

Related Manuals for Panasonic TH-103PF12E

Summary of Contents for Panasonic TH-103PF12E

  • Page 1: Table Of Contents

    Order Number PCZ0912156CE Service Manual High Definition Plasma Display TH-103PF12E Model No. G PF12D Chassis WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
  • Page 2 TH-103PF12E 9.15. Removal of S1-Board and V 2-B oard------------------30 9.16. Removal of S U -B o a rd --------------------------------------- 31 9.17. Removal of S M -B o a rd ---------------------------------------32 9.18. Removal of S D -B o a rd ---------------------------------------32 9.19.

  • Page 3: Safety Precautions

    TH-103PF12E 1 Safety Precautions 1.1. General Guidelines 1. W hen conducting repairs and servicing, do not attem pt to modify the equipment, its parts or its materials. 2. W hen wiring units (with cables, flexible cables or lead w ires) are supplied as repair parts and only one wire or some of the wires have been broken or disconnected, do not attem pt to repair or re-wire the units.

  • Page 4: Arn Ing

    TH-103PF12E 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi­ tive (ES) Devices Some sem iconductor (solid state) devices can be damaged easily by static electricity. Such com ponents com m only are called Elec­ trostatically Sensitive (ES) Devices. Exam ples of typical ES devices are integrated circuits and some field-effect transistors and sem iconductor “chip”...

  • Page 5: About Lead Free Solder (Pbf)

    TH-103PF12E 2.2. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the inform ation below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

  • Page 6: Ervice N Avigation

    TH-103PF12E 3 Service Navigation 3.1. Service Hint...
  • Page 7 TH-103PF12E Board Name Function Board Name Function Digital S ignal Processor, M icrocom puter P ow er switch Form at C onverter, Plasm a AI Processor C1 (upper) Data drive (1) (upper) Sub-Field Processor C2 (upper) Data drive (2) (upper)

  • Page 8: Applicable Signals

    TH-103PF12E 3.2. Applicable signals *M a rk: A p p lic a b le in p u t sig n a l C O M P O N E N T / H o riz o n ta l fre q u e n c y...

  • Page 9: P Ec Ifica Tio N S

    TH-103PF12E 4 Specifications P o w e r S o u rc e 220-240 V A C, 50/60H z P o w e r C o n s u m p tio n Pow er on 1450 W S tand-by condition S ave O F F 1.2 W, S ave ON 0.7 W...

  • Page 10: Operating Instructions

    TH-103PF12E 5 Operating Instructions...
  • Page 11 TH-103PF12E O ption Menu for G P F12D series GPF12D chassis series have special function and operation setting facility called Option Menu. This Option Menu is useful for special function required custom ers. This should be set at the installation stage.

  • Page 12: Service Mode

    TH-103PF12E 6 Service Mode 6.1. CAT (Computer Aided Test) mode To exit the CAT m ode, access the ID mode and switch off the main power. 6.1.1. IIC mode Select the IIC mode by Up/Down button on the remote control at the front page of CAT mode and then press the Action button on the remote control.
  • Page 13 TH-103PF12E 6.1.2. CD mode Select the CD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. M O N ITOR-MCU 1.0000Ғ12...
  • Page 14 TH-103PF12E 6.1.4. SD mode Select the SD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Action button on the remote control. To exit the SD mode, press the R button on the remote control.
  • Page 15 TH-103PF12E 6.1.6. ID mode Select the ID mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. To exit the ID mode, press the R button on the remote control.

  • Page 16: Iic M Ode Structure (Following Items Value Is Sam Ple Da

    TH-103PF12E 6.2. IIC mode structure (following items value is sample data)

  • Page 17: Troubleshooting Guide

    TH-103PF12E 7 Troubleshooting Guide 7.1. Self Check 7.1.1. Display Indication 1. Self-check is used to automatically check the bus line controlled circuit of the Plasma display. 2. To get into the Self-check mode, press the volum e down button on the customer controls at the bottom of the set, at the same tim e pressing the O FF-TIM ER button on the remote control, and the screen will show.
  • Page 18 TH-103PF12E 7.1.2. Power LED Blinking timing chart 1. Subject Information of LED Blinking tim ing chart. 2. Contents When an abnormality has occurred to the unit, the protection circuit operates and resets to the stand by mode. A t this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.

  • Page 19: No Power

    TH-103PF12E 7.2. No Power First check point There are following 3 states of No Power indication by power LED. 1. No lit. 2. Green is lit then turns red blinking a few seconds later. 3. Only red is lit. 7.3.

  • Page 20: Local Screen Failure

    TH-103PF12E Drive circuits LED indicator SC board SS board Ґ ґ LED ^ " n ' — D16583 D16253 7.4. Local screen failure Plasma display may have local area failure on the screen. Fig - 1 is the possible defect P.C.B. for each local area.

  • Page 21: Service Fixture & Tools

    TH-103PF12E 8 Service Fixture & Tools 8.1. SC jig Purpose: To find the failure board (SC or SU/SM /SD) when the power LED is blinking 7 times. SC jig: Jum per connector to connect to SC50 connector on SC board...

  • Page 22: Disassembly And Assembly Instructions

    TH-103PF12E 9 Disassembly and Assembly Instructions • To disassem ble P.C.B., wait for 10 minute after power was off for discharge from electrolysis capacitors. • O , ♦ and 'u1 marks indicate screw positions. 9.1. Rear Cover and Board Rear Cover required to remove for each board exchange.

  • Page 23: Location Of Rear Cover Screws

    TH-103PF12E B o a rd N am e R ear C o v e r V 3-B oard A, B, C, D, E, F P B-Board P-Board (M AIN_1) P-Board (M AIN_2) P-Board (SUB) D, E HX-Board HL-Board U nnecessary...
  • Page 24 TH-103PF12E (x21 O, x2 9.2.3. Removal of Rear Cover ( С ) Remove screws □ ) and then remove the Rear Cover ( A ). 1. Remove screws (x19 О ) and then remove the Rear Cover ( C ).

  • Page 25: Removal Of Side Angle (L), (R)

    TH-103PF12E 9.2.5. Removal of Rear Cover ( E ) 2. Remove screws (x21 О ) and then remove the Rear Cover ( F ). 1. Remove screws (x25 О ) and then remove the Rear Cover ( E ). 9.3.

  • Page 26: Removal Of Hde-Board

    TH-103PF12E 2. Remove 19 screws and then remove the Side Angle (L). 5. Remove 4 screws (B) of the Plate. 6. Remove 19 screws and then remove the Side Angle (R). 9.3.2. Removal of Side Angle (R) 1. Disconnect the connectors (DS15, P34).

  • Page 27: Removal Of Hl-Board

    TH-103PF12E 9.5. Removal of HL-Board 3. Remove 2 screws (J). 4. Remove 1 screw (K) and then remove H5-Board. 1. Remove 4 screws (F) and then remove the HL Terminal Block. 2. Remove 4 screws (G). 3. Remove 2 screws (H) and then remove HL-Board.

  • Page 28: Removal Of Hx-Board

    TH-103PF12E 4. Disconnect the connector (DS14). 1. Remove the Slot Case. 5. Remove 10 screws and then remove the Fixed Plate (Refer to Removal of DS-Board) 2. Disconnect the connector (HX1). 3. Remove 4 Hexagonal-Head screws and 2 screws and then remove HX-Board.

  • Page 29: Removal Of Pb-Board

    TH-103PF12E 9.10. Removal of PB-Board 2. Disconnect the connectors (D3, D5, D21, D25). 3. Remove the flexible cables from the connectors (D20, D31, D32, D33, D34). 4. Remove 4 screws and then remove D-Board. 1. Disconnect the connectors (PB30, PB31, PB51, PB53, PB54, PB59, PB61, PB62, PB67, PB69, PB71).

  • Page 30: Removal Of P-Board (Main_2)

    TH-103PF12E 9.13. Removal of P-Board (MAIN_2) 9.15. Removal of S1-Board and V2- Board 1. Disconnect the connectors (CM1, CM2, CM3, CM4, P6, P11, P35). 1. Remove 2 screws (♦ ). 2. Remove 10 screws and then remove P-Board (MAIN_2). 2. Remove 2 screws (0 ) and then slide the Side Power Unit upward.

  • Page 31: Removal Of Su-Board

    TH-103PF12E 9.15.2. Removal of V2-Board 4. Disconnect the Fan relay connectors. 5. Remove 4 screws and then remove the Fan Block (2, 3). 1. Remove 4 screw (N) and then remove the Side Power Cover. 2. Disconnect the connector (V15) and then remove V2- Board.

  • Page 32: Removal Of S M -B O A

    TH-103PF12E 10. Disconnect the connector (SU43). 4. Remove the flexible cables from the connectors (SM1, SM2, SM3, SM4, SM11, SM12). 11. Remove 5 screws (♦ ). 12. Remove 3 screws (O) and then remove SU-Board. 9.17. Removal of SM-Board 5. Disconnect the connectors (SM41, SM42, SM46) 6.

  • Page 33: Removal Of Sc-Board

    TH-103PF12E 1. Remove the Side Angle (R). 8. Remove the flexible cables from the connectors (SD1, (Refer to Removal of the Side Angle (R)) SD2, SD3, SD4, SD12). 2. Remove 3 screws (♦ ). 3. Remove 3 screws (O) and then remove the Reinforce­...

  • Page 34: Removal Of Ss2-Board

    TH-103PF12E 9.20. Removal of SS2-Board 1. Remove SU-Board. (Refer to Removal of SU-Board) 2. Remove SD-Board. (Refer to Removal of SD-Board) 3. Disconnect the connectors (SM41, SM42, SM46). 4. Remove 6 screws (♦ ). 5. Remove 4 screws (O) and then turn over SM-Board to the left.

  • Page 35: Removal Of Ss3-Board

    TH-103PF12E 6. Disconnect the connectors (SS34, SS35). 4. Disconnect the connectors (SS32, SS33). 7. Remove the flexible cables from the connectors (SS51, 5. Remove the flexible cables from the connectors (SS59, SS52, SS53, SS54). SS60, SS61, SS62). 8. Remove 6 screws and then remove SS2-Board.

  • Page 36: Removal Of Fan

    TH-103PF12E 5. Disconnect the connectors (SS11, SS21, SS32, SS33, SS34, SS35). 6. Remove the flexible cables from the connectors (SS55, SS56, SS57, SS58). 7. Remove 13 screws and then remove SS-Board. 9.23. Removal of Fan 3. Remove each 4 screws and then remove the Fan (A, B, C, D, E, F, G, H, J).

  • Page 37: Removal Of C1-Board (U P P E

    TH-103PF12E 1. Remove the Reinforcem ent Angle (upper_right). (Refer to Removal of SU-Board) 2. Remove the flexible cable from the connector (C11). 3. Remove 4 screws ( ♦ ) and then remove the flexible cables from the connectors (CA1, CA2).

  • Page 38: Removal Of C3-Board (Upper)

    TH-103PF12E 9.26. Removal of C3-Board (upper) 7. Remove the flexible cables from the connectors (C30, C31, C32). 8. Remove 6 screws ( ♦ ) and then remove the flexible cables from the connectors (CA6, CA7, CA8). 9. Remove 6 screws (0 )

  • Page 39: Removal Of C5-Board (Upper)

    TH-103PF12E 9.28. Removal of C5-Board (upper) 1. Remove the Reinforcem ent Angle (upper_left). (Refer to Removal of SS2-Board) 2. Remove the flexible cable from the connector (C61). 3. Remove 4 screws ( ♦ ) and then remove the flexible cables from the connectors (CA15, CA16).

  • Page 40: Removal Of C2-Board (Low

    TH-103PF12E 9.31. Removal of C2-Board (lower) 2. Remove 3 screws (♦ ). 3. Remove 2 screws (O) and then remove the Rear Cover Angle (lower_center). 1. Remove the Reinforcem ent Angle (lower_left). (Refer to Removal of SS3-Board) 2. Remove the flexible cables from the connectors (C20, 4.

  • Page 41: Removal Of C5-Board (Lower)

    TH-103PF12E 9.35. Removal of C6-Board (lower) 1. Remove the Reinforcem ent Angle (lower_center). (Refer to Removal of C3-Board (lower)) 2. Remove the flexible cables from the connectors (C40, C41, C42). 3. Remove 6 screws ( ♦ ) and then remove the flexible cables from the connectors (CA9, CA10, CA11).

  • Page 42: Removal Of Front Glass, V1, V3-Board And Cabinet Assy

    TH-103PF12E 1. Remove 2 screws and then remove AC Inlet Cover. 2. Remove 2 screws (♦ ). 3. Remove 2 screws (O) and then slide the Side Power Unit upward. 4. Remove the Side Power Unit. 5. Remove 24 screws and then remove Cabinet Block.
  • Page 43 TH-103PF12E 9.37.1. Removal of Front Glass Note: when Cabinet or Front Glass is exchanged • You need new Alum inum Tape kit when you exchange 1. Remove 44 screws and then remove the Fixed Angles the Cabinet or Front Glass.
  • Page 44 TH-103PF12E 9.37.2. Removal of V1-Board and V3-Board 4. Remove 20 screws and then remove the Cabinet Joint M etals (B, BS). 1. Remove 1 screw (P). 2. Disconnect the connector (V1) and then remove V1- Board. 3. Remove 1 screw (Q).

  • Page 45: Removal Of Plasma Display Panel

    TH-103PF12E Note: when Cabinet or Front Glass is exchanged • You need new AL Tape kit when you exchange the Cab­ inet or Front Glass. Note • The felts are parts which cannot be recycled. Please use the new article when you exchange the Cabinet.
  • Page 46 TH-103PF12E 9. Remove each 4 screws (R) of the Plates. 3. Remove 2 screws (♦ ). 4. Remove 2 screws (O) and then slide the Side Power Unit upward. 5. Remove the Side Power Unit. 6. Remove 24 screws and then remove Cabinet Block.
  • Page 47 TH-103PF12E 13. Remove 6 screws (♦ ). 14. Remove 4 screws and then remove the Rear Cover ( 0 ) Angles (upper_center, lower_center). 17. Disconnect the connectors (DN3, DN5, DN9). 18. Remove the flexible cables from the connectors (DN1, DN2).
  • Page 48 TH-103PF12E Disconnect the connectors (DS4, DS6). 28. Disconnect the connectors of P-Board (Main_2) (CM1, Remove 3 screws and then remove the Slot Block. CM2, CM3, CM4, P6, P11). 29. Remove 10 screws and then remove P-Board (MAIN_2). 30. Disconnect the connectors (P9, P25).
  • Page 49 TH-103PF12E 36. Remove 4 screws and then remove PB-Board. 40. Remove the Duct Barrier E, Duct Barriers F, Duct Barrier G, Duct Barrier H, Duct Barrier L, Duct Barrier N and Duct Barrier O. * ____ 3 ­ 41. Exchange the Plasma Display Panel.

  • Page 50: Measurements And A D Ju S Tm E N

    TH-103PF12E 10 Measurements and Adjustments 10.1. Adjustment Procedure 10.1.1. Driver Set-up 10.1.1.1. Item / Preparation 10.1.1.2. Adjustments 1. Set Aging pattern (white pattern signal) by IIC mode. 2. Set the picture controls as follows. Adjust driver section voltages. (Refer to the panel data on the Picture menu: Standard Panel Label).
  • Page 51 TH-103PF12E 10.1.2. Initialization Pulse Adjust 1. Set Aging pattern (white pattern signal) by IIC mode. 2. Set the picture controls as follows. Picture menu: Standard Picture: +25 Aspect: Full 3. Connect O scilloscope to TPSC1 and adjust VR16601 for 125V ± 5V.
  • Page 52 TH-103PF12E 10.1.3. P.C.B. (Print Circuit Board) and Plasma Display Panel exchange 10.1.3.1. Quick adjustment after P.C.B. and Panel exchange 1. To remove P.C.B., w ait 10 minute after power was off for discharge from electrolysis capacitors. 10.1.3.2. Quick adjustment after P.C.B. exchange Adjust the following voltages with the multimeter.
  • Page 53 TH-103PF12E 3. C heck that the Ve Mode is set to 3. Ve M o d e :3 4. Pless R button and then select and display Ve Init. Ve Init 5. C heck TPVE and adjust the volume. 6. Exit the IIC mode.
  • Page 54 TH-103PF12E 10.1.9. Adjustment Volume Location 10.1.10. Test Point Location...

  • Page 55: Adjustment

    TH-103PF12E 10.2. Adjustment 10.2.1. RGB white balance adjustment Instrum ent Name C onnect to Setting R G B V G A 60 W / B pattern PC input U ser setting: Normal C olor analyzer Panel surface (Picture menu: STANDARD)
  • Page 56 TH-103PF12E Table 2 Drive data addresses (PC/RGB) C olor tem perature В C O O L(H i) AO-11 AD A 0-11A E A 0-11A F AO-11 BO AO-11 B1 AO-11 B2 N O R M A L(M id) W A R M (Low )
  • Page 57 TH-103PF12E 10.2.2. YUV white balance adjustment Instrum ent Name C onnect to Setting HD(1125/60i) W / B pattern (C O M P O N E N T Output) PC input U ser setting: Normal C olor analyzer Panel surface (Picture menu: STANDARD)
  • Page 58 TH-103PF12E Table 7 Drive data addresses (YUV2_HD) C olor tem perature В C O O L(H i) A 0-119B A 0-119C A 0-119D N O R M A L(M id) A 0-119E A 0-119F AO-11 AO A0-11A1 A 0-11A 2...

  • Page 59: Block D Ia G Ra

    TH-103PF12E 11 Block Diagram 11.1. Diagram Notes Notes: Resistor Remarks: Unit of resistance is OHM [Q] (K=1,000, M =1,000,000). 1. The Power Circuit contains a circuit area which uses a separate power supply to isolate the Capacitor earth connection. Unit of capacitance is цҒ, unless otherwise noted.

  • Page 60: Main Block (1 Of 2) Diagram

    TH-103PF12E 11.2. Main Block (1 of 2) Diagram ■ D5 ' D3...

  • Page 61: Main Block (2 Of 2) Diagram

    TH-103PF12E 11.3. Main Block (2 of 2) Diagram...

  • Page 62: Block (1 Of 8) Diagram

    TH-103PF12E 11.4. Block (1 of 8) Diagram I H D E | d v i i n t e r f a c e...

  • Page 63: Block (2 Of 8) Diagram

    TH-103PF12E 11.5. Block (2 of 8) Diagram SLOI1 SLOI2 SLOT3...

  • Page 64: Block (3 Of 8) Diagram

    TH-103PF12E 11.6. Block (3 of 8) Diagram...

  • Page 65: Block (4 Of 8) Diagram

    TH-103PF12E 11.7. Block (4 of 8) Diagram...

  • Page 66: Block (5 Of 8) Diagram

    TH-103PF12E 11.8. Block (5 of 8) Diagram...

  • Page 67: Block (6 Of 8) Diagram

    TH-103PF12E 11.9. Block (6 of 8) Diagram ГР F O R M A T C O N V E R T E R , P L A S M A A I P R O C E S S O R...

  • Page 68: Block (7 Of 8) D Iagra

    TH-103PF12E 11.10. Block (7 of 8) Diagram |S S 2 | s u s t a i n C O N N E C T O R ( U P P E R ) S C A N D R IV E...

  • Page 69: Block (8 Of 8) D Iagra

    TH-103PF12E 11.11. Block (8 of 8) Diagram...
  • Page 70 TH-103PF12E...

  • Page 71: Iring Connection D Iag Ram

    TH-103PF12E 12 Wiring Connection Diagram 12.1. Wiring (1)

  • Page 72: W Iring (2 )

    TH-103PF12E 12.2. Wiring (2) The lead line on Fan Fixed Plate are Core passed through the cut holes of the barrier. / Clamp position © © C ON:No - CON:No © © © © © © © © © ©...

  • Page 73: W Iring (3 )

    TH-103PF12E 12.3. Wiring (3)

  • Page 74: Exploded View And Replacem Ent Parts L Is T

    Model No. : TH-103PF12E Important Safety Notice Note: All parts except parts mentioned [PAVCC2] in the Remarks column are supplied by AVC-CSPC Parts mentioned [PAVCCZ] are supplied by PAVCCZ.
  • Page 75 Model No. : TH-103PF12E Exploded View...
  • Page 76 Model No. : TH-103PF12E Side Power part location...
  • Page 77 Model No. : TH-103PF12E Cabinet part location...
  • Page 78 Model No. : TH-103PF12E Fan part location...
  • Page 79 Model No. : TH-103PF12E Rear cover location...
  • Page 81 Model No. : TH-103PF12E Printed Circuit Board...
  • Page 82 Model No. : TH-103PF12E Cable relation...
  • Page 83 Model No. : TH-103PF12E Packing summary (1) Д75 K2CN3YY00003 K2CT3YY00002 Round pin Rectangular blade...
  • Page 84 Model No. : TH-103PF12E Packing summary (2)
  • Page 85 Model No. : TH-103PF12E Packing summary (3)
  • Page 86 Model No. : TH-103PF12E Packing summary (4)
  • Page 87 Model No. : TH-103PF12E Packing summary (5)
  • Page 88 Model No. : TH-103PF12E Packing summary (6)
  • Page 89 Model No. : TH-103PF12E Packing summary (7)
  • Page 90 TKKX0015 HEXAGONAL WRENCH TKUX115 01 REAR COVER (C/L/U) TKYA41601T CABINET UPPER 1 ENCLOSED 2 FELT TAPES ENCLOSED 2 FELT TAPES AND PANASONIC BADG TKYA41701T CABINET BOTTOM TKYA41801T CABINET SIDE L/R 2 ENCLOSED FELT TAPE TMKA5 8 0 CABINET FELT (LEFT/RIGHT)
  • Page 91 Model No. : TH-103PF12E Parts List R e f . j Safety Part No. Part Name & Description Q'ty Remarks TMKY910 DUCT BARRIER F TMKY911 DUCT BARRIER G TMKY912 DUCT BARRIER H TMKY914 DUCT BARRIER J TMKY915 DUCT BARRIER K...
  • Page 92 Model No. : TH-103PF12E Parts List R e f . jsafety Part No. Part Name & Description Q'ty Remarks No . TPDA1419 CUSHION (CENTER) TPDF17 4 6 ACCESSORIES BOX TPDX0 0 0 7 JOINT TPDX0027 BOTTOM SKID TPDX0041 BAND TPEH323...
  • Page 93 Model No. : TH-103PF12E Parts List R e f . j Safety Part No. Part Name & Description Q'ty Remarks TTUA17 7 9-1 REAR COVER (R) ASSY 1 PAVCCZ TTUA2317 REAR COVER (L) ASSY TUWC05 6 SIDE POWER COVER TUXJ35 0...
  • Page 94 Model No. : TH-103PF12E Parts List R e f . Safety Part No. Part Name & Description Q'ty Remarks XZBT65 0 6 POLY BAG (INSTRUCTION BOOK) ETX2MM7 8 0MG CIRCUIT BOARD P (MAIN) & ETX2MM7 8 0MGA CIRCUIT BOARD P (SUB)

Table of Contents