General Speci Cations; Important Notice - DeWalt DXFRS800 Owner's Manual

Operation

General Speci cations

Frequency Allocation and Compatibility
A = Channel No. for 22 Channel Models
B = Frequency in MHz
C = Power Output
A
1 462.5625
2 462.5875
3 462.6125
4 462.6375
5 462.6625
6 462.6875
7 462.7125
8 467.5625
9 467.5875
10 467.6125
11 467.6375
12 467.6625
13 467.6875
14 467.7125
15 462.5500
16 462.5750
17 462.6000
18 462.6250
19 462.6500
20 462.6750
21 462.7000
22 462.7250

IMPORTANT NOTICE:

WARNING: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must accept any
interference received,including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
13
B C
High
High
High
High
High
High
High
Low
Low
Low
Low
Low
Low
Low
High
High
High
High
High
High
High
High
• Consult the dealer or an experienced radio/TV technician for help.
Safety Information for Radios
Your wireless handheld portable transceiver contains a low power transmitter. When the talk button
is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty
factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted
RF exposure guidelines with safety levels for handheld wireless devices
Important
FCC/ISEDC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets
the FCC/ISEDC RF exposure guidelines when used with D
this product. Use of other accessories may not ensure compliance with FCC/ISEDC RF exposure guidelines.
Use only the supplied antenna. Unauthorized antennas, modifcations or attachments could damage the
transmitter and may violate FCC/ISEDC regulations.
Normal Position
Hold the transmitter approximately 25 mm from your face and speak in a normal voice, with the
antenna pointed up and away.
ISEDC WARNING
This device complies with ISEDC license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Under ISEDC regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by ISEDC. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
The applicant is responsible for providing proper instructions to the user of the radio device, and any
usage restrictions, including limits of exposure durations. The user manual shall provide installation
and operation instructions, as well as any special usage conditions, to ensure compliance with SAR
and/or RF field strength limits. For instance, compliance distance shall be clearly stated in the user
manual.
Cet appareil est conforme aux normes RSS exemptes de licence ISEDC. Son fonctionnement est
soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2)
cet appareil doit accepter toute interférence, y compris les interférences pouvant entraîner un
fonctionnement indésirable de l'appareil. En vertu des réglementations ISEDC, cet émetteur radio
ne peut fonctionner qu'avec une antenne d'un type et un gain maximal (ou inférieur) approuvé
pour l'émetteur par l'ISEDC. Pour réduire les interférences radio potentielles avec d'autres
utilisateurs, le type d'antenne et son gain doivent être choisis de manière à ce que la puissance
isotrope rayonnée équivalente (e.i.r.p.) ne soit pas supérieure à celle nécessaire à une
communication réussie.
Le demandeur est responsable de fournir des instructions appropriées à l'utilisateur du dispositif
radio et de toute restriction d'utilisation, y compris les limites de la durée d'exposition. Le manuel
de l'utilisateur doit fournir des instructions d'installation et d'utilisation, ainsi que des conditions
d'utilisation spéciales, pour assurer la conformité avec les limites de champ de SAR et / ou RF. Par
exemple, la distance de conformité doit être clairement indiquée dans le manuel d'utilisation.
Important:
Exigences de la FCC/ISEDC concernant l'exposition aux champs électro-magnétiques RF (radiofréquences):
En ce qui concerne le fonctionnement de l'appareil porté sur le corps de l'utilisateur, les tests effectués ont
permis de véri er que cet émetteur-récepteur satisfait aux directives FCC/ISEDC limitant l'exposition aux champs
électro-magnétiques RF lorsqu'il est utilisé avec les accessoires Cobra fournis ou conçus pour ce produit;
l'utilisation d'autres accessoires peut ne pas garantir le respect des critères des directives FCC/ISEDC limitant
l'exposition aux champs électro-magnétiques RF. Utiliser l'appareil uniquement avec l'antenne fournie.
L'emploi d'une antenne non homologuée ou modi ée, ou d'accessoires non autorisés, pourrait faire subir
des dommages à l'appareil, et peut violer les prescriptions de la réglementation FCC/ISEDC.
Position normale:
Tenir l'émetteur à environ 25 mm de la bouche et parler normalement, l'antenne étant éloignée et
dirigée vers le haut.
WALT accessories supplied or designated for
E
14