Table of Contents
Advertisement
Quick Links
Huskvarna, 2018-03-12
Safety and Operating Instructions
Dear customer,
thank you for choosing a Husqvarna quality product. We hope that you will genuinely enjoy it.
Please note that the enclosed manual contains Atlas Copco references.
The Husqvarna Group is vouching for the quality of this product.
If you have any questions, please do not hesitate to contact our local sales or service point.
Husqvarna AB
561 82 Huskvarna, Sweden
Advertisement
Table of Contents
Related Manuals for Atlas Copco LH804
Summary of Contents for Atlas Copco LH804
- Page 1 Dear customer, thank you for choosing a Husqvarna quality product. We hope that you will genuinely enjoy it. Please note that the enclosed manual contains Atlas Copco references. The Husqvarna Group is vouching for the quality of this product. If you have any questions, please do not hesitate to contact our local sales or service point.
- Page 2 Safety and operating instructions Forward and reversible plate © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions...
-
Page 4: Table Of Contents
Operation..............21 © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01... - Page 5 EC Declaration of Conformity (EC Directive 2006/42/EC)......32 © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01...
-
Page 6: Introduction
Safety and operating instructions Introduction Thank you for choosing a product from Atlas Copco. Since 1873, we have been committed to finding new and better ways of fulfilling our customers' needs. Through the years, we have developed innovative and ergonomic product designs that have helped customers improve and rationalize their daily work. -
Page 7: Safety Instructions
Fill the fuel tank at least ten meters (30 Protective gloves ● feet) from the place where the machine is to be used. ● Proper protective boots © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... - Page 8 Ensure that only authorized personnel operate the ► machine. Never give the transmitter to anyone who is not ► fully familiar with the machine, its operation and safety directives. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions...
- Page 9 © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions...
- Page 10 See the ”Noise and vibration declaration statement” for the machine, including the declared vibration values. This information can be found at the end of these Safety and operating instructions. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions...
-
Page 11: Transport, Precautions
If the machine has a silencer, check that it is in ► place and in good working condition. ► Always use hearing protection. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 12: Overview
Hose for oil drainage Oil drain plug Engine oil filter Oil dipstick Air filter Shock absorbers Eccentric element Electronic Control Unit (ECU) Water separator Hydraulic reservoir © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 13: Labels
The labels must be in such condition that they are easy to read. New labels can be ordered from the spare parts list. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 14: Data Plate
"Technical data" for accurate noise level. Engine information label Master switch Safety label Instruction manual. The operator must read the safety, operation and maintenance instructions before operating the machine. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 15: Lifting Point Label
Pulling forces must act longitudinally on the machine. Maximum permitted pulling force is 15 kN horizontally in the longitudinal axis of the machine. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 16: Secure Transport
Only trained personnel who are fully familiar with Avoid spilling fuel and wipe off any fuel spilled on ► the control system may operate the machine. the machine. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 17: Transmitter
15 minutes. Change the battery and make sure that the slot and contact surfaces are The receiver (A) is mounted under the rear service clean. hood. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 18: Pairing Function
How to set the receiver in pairing mode: Paired Steady green. When pairing has been successfully accomplished, restart the transmitter. Restart the reciever by pressing the stop knob. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 19: Antenna
Switch off the machine and lift it back on surface ► with full bearing strength. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 20: Start And Stop
We recommend to study the engine manual supplied with the machine. Check that the maintenance routines have been carried out. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 21: Starting The Engine, Hatz
Always have an extra fully-charged battery available. System information When the transmitter is turned on, the following data will be shown on the display: © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 22: Stopping The Engine, Hatz
LED indicator light turns off. 7. Place the transmitter in its transportation position in the machine or store it in a safe place. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 23: Control
Never connect the welder grounding cable to the diesel engine. Disconnect all cables from the receiver and ECU before performing any welding on the machine. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 24: Desktop Charger
♦ The desktop charger works within a voltage range of100-240 V. ♦ The desktop charger comes with an adapter that works in most sockets. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 25: Every 10 Hours Of Operation (Daily)
Check the functions of the transmitter and the receiver. ♦ Check the engine for oil leaks. ♦ Clean and refit the air filter (A) if needed. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 26: Checking Bolted Joint
NOTICE Never aim a water jet directly at the fuel filler cap. This is particularly important when using a high-pressure cleaner. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 27: Hydraulic System, Checking The Hydraulic Oil
Change eccentric element oil. ♦ Change hydraulic fluid and filter. 2. Drain until only pure fuel is left in the bowl. 3. Refit the drainage plug (A). © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 28: Changing The Oil In The Eccentric Element
Empty the fuel tank before storing the machine. ♦ Clean the machine. ♦ Clean the air filter. ♦ Wipe off any oil and dust that has accumulated on the rubber parts. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... - Page 29 Safety and operating instructions LH 804 Cover the machine and store it in a dry, dust-free ♦ area. © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions...
-
Page 30: Technical Data
13849-1 PL e (EN954-1, Cat 4). Operating frequency, GHz BlueTooth, 2.4 Indication, receiver Triple-colour LED, Red/Green/Yellow. Indication, CAN status Twin-colour LED Red/Green. Protection class IP 66 © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 31: Weights For Options
We, Atlas Copco Construction Tools AB, cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. -
Page 32: Dimensions
(in.) *Contact area m (sq feet). 0.290 (3.12)*/ 0.646 (6.95)*/ 0.712 (7.66)* 1050 (41) 1150 (45) 660 (26) 810 (32) / 960 (38) © 2013 Atlas Copco Construction Tools AB | No. 9800 1387 01 | 2013-07-01 Original instructions... -
Page 33: Ec Declaration Of Conformity
EC Declaration of Conformity EC Declaration of Conformity (EC Directive 2006/42/EC) We, Atlas Copco Construction Tools AB, hereby declare that the machines listed below conform to the provisions of EC Directive 2006/42/EC (Machinery Directive) and 2000/14/EC (Noise Directive), and the harmonised standards mentioned below. - Page 37 Any unauthorized use or copying of the contents or any part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers, and drawings. www.atlascopco.com...
Need help?
Do you have a question about the LH804 and is the answer not in the manual?
Questions and answers