HKS OB-Link Type 001 Instruction Manual

Instruction Manual

Prior to installation and use, thoroughly read the
instruction manual. Retain this instruction manual
for later reference.
Pursuing the Ultimate in Engine Performance and Efficiency.
HKS Company Limited.
Instroduction
Thank you for purchasing HKS OB-LINK TYPE-001.
OB-LINK TYPE-001 is a device which plugs into to a
vehicle OBD II port and transmits vehicle data
(Engine Rpm, Water Temperature, Oil Temperature,
A/F correction and feedback, Fuel
economy,Brake,Steering rudder angle,etc.) by
Bluetooth connection.
The information from OB-LINK TYPE-001 can be
displayed by installing exclusive application
(CarscopePlus, OB-BRIDGE) in Android / iOS device.
The OB-LINK TYPE-001 has a logging function. If
application (OBLink LogManager) for exclusive use
performs a logging setup, log data is saved OB-LINK
TYPE-001.
The saved data can be read by OBLink LogManager.
Product Name OB-LINK TYPE-001
Purpose Wireless (Bluetooth) Vehicle Data Transmission
Device
Product Code 44009-AK002
●This manual indicates items you need to pay attention to in order to
install this product safely and lists precautions to avoid any possible
damage and/or accidents.
●HKS will not be responsible for any damage caused by incorrect use or
use after modification and/or dismantling of this product.
- 1 -
●This product was designed for installation and use on a factory vehicle or
a vehicle using other HKS products.The performance and/or safety
cannot be guaranteed if this product is installed onto other vehicles
than mentioned above.
●This product is applicable for any vehicle that operates on a DC12V
negative ground.
●The specifications of this product, including installation are subject to
change without prior notice.
Contents
Introduction ........................ 1
Contents...........................2
Safety Precautions ............... 2
Parts List ........................... 3
Installation ........................ 3
Safety Precautions
Below are symbols used in this manual to highlight areas where.
-Risk of severe injury or death may result if
warning is not acknowledged or followed.
C98911-K00550-00
2014/04/25
Ver.3-1.01
-Risk of injury to self, damage to vehicle or
property may result if caution is not taken.
● Make sure to work on the vehilce in a well-ventilated area to
prevent possible explosion or fire.
Do not mount the unit where it can distract driving.
● Do not install this product on a 24V vehicle. It is designed for
use on a 12V vehicle.
● Make sure to hold connectors when removing them to avoid
possible damage to other electronic parts caused by
disconnections or by a short circuit.
Stop using the product if any unusual conditions are oticed;
it may cause a fire or an electrical shock.Consult an
authorized dealer immediately.
● Do not modify, disassemble and/or remodel this product and
any of its attached parts.
● Handle the parts with caution at all times.
● Avoid allowing oil and/or water from entering the unit.It may
cause damage to the engine.
● Make sure all connections and wiring are not disconnected,
short circuited, or incorrect. If so,it may cause an electric
shock, burn out, or damage to the vehicle.
● If the product or the vehicle with the product does not perform
properly, consult the dealer immediately.
●Daily check-up of the vehicle must be done by the owner.
Operation and Use ............... 5
Maintenance ........................ 6
Product Specfications............6
Revision of Manual ............... 6
Warning
Caution
Warning
Caution
- 2 -
Parts List
Make sure that all of the parts listed in the Parts List are
included in the kit.
OB-LINK TYPE Splice
IG signal-Pick-up
2 3
1
-001 Main Unit Loop tape
harness
Installation
1.Locate OBD II port
Locate the OBD II port plug on the vehicle. Details
can be found from the following website address:
http://www.hks-power.co.jp/en
/product/electronics/monitor/
ob-link/index.html
2. Install Application
① Installation of "OB-BRIDGE" (for Android)
② Installation of "CarscopePlus"
③ Installation of "OBLink LogManager※"
※ It is required to use the log function of OB-LINK
TYPE-001.
(June, 2014 release)
Please search the application from a store or
download it from the section 1.
3.Bluetooth Setting (Pairing)
① Switch on the Bluetooth of the device to be paired.
② Connect the OB-LINK TYPE-001 to the OBD II port
found in section 1.
③ Please start the engine, or you turn "ON" a key
switch.
④ Pair the devices using Bluetooth passkey "7181"
4. Application Initial Setup
Launch CarscopePlus and tap setting.
① Select Device
Tap device select on setting menu.
Select OB-LINK 001 in the Paired device list.
- 3 -
Instruction
4
Manual