Table of Contents
Advertisement
Quick Links
1573 Savoie
C. P . 4 Plessisville, Qc.
G6L 2Y6
TEL: 819-362-7207
FAX: 819-362-2045
www.leclerclooms.com
info@leclerclooms.com
IMPORTANT
14 1/8"
Loom Prepared by:_____________
Inspected by:_________________
Date:____________________
ARTISAT 36" JACK-TYPE
8 SHAFTS BACK HINGE
TREADLES
1009-3628
On receiving the loom, unpack and lay
out the loom components.
Do NOT discard any packing material until all
parts are inventoried.
Check the parts received against the
Parts List on pages #2 to #6 of the assembly
instructions. Report any discrepancies to
Leclerc immediately.
To assemble this loom, a minimum of 2
people are needed but it is recommended
you use 3.
1
Advertisement
Table of Contents
Related Manuals for Leclerc Looms ARTISAT 36 inch
Summary of Contents for Leclerc Looms ARTISAT 36 inch
- Page 1 ARTISAT 36” JACK-TYPE 8 SHAFTS BACK HINGE TREADLES 1009-3628 1573 Savoie C. P . 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all parts are inventoried.
- Page 2 PARTS LIST 39¾" 8 FLOATING LAMS 41½ cc 1 CASTLE TOP COVER Note for Leclerc in French: 1) Poser les 2 vis de la base de pattes arrière pour le crochet. Tête ronde no 12, 1" avec rondelle de nylon 1 LEFT-HAND SIDE 2) Poser la pièce filetée with base packed seperatly...
- Page 3 1 PK. 10 YDS FOR BEAM STICK 1 PK 5 YDS FOR BEAMING AND LEASE STICKS 1 SHUTTLE 1 DOZ. BOBINES 4" 1 CLOTH BEAM WITH RATCHET WHEEL (wood = 38 1/8") 1 WARP BEAM WITH BRAKE DRUM (wood = 38 7/8") 1 TAKE-UP MOTION HANDLE 1 BATTEN HANDTREE 1 BATTEN SLEY WITH SHUTTLE RACE...
- Page 4 Note for Leclerc in French: La planche avant et arrière de la 1 JACK BOX boite à marmousset doit avoir les vis pour cordes à bascule (DO NOT REMOVE THE et ressort à pédale TAPE UNTILL IT IS 2 X 10 vis #12 x ¸¾” INSTALLED IN THE LOOM) (back part) 20 3/8"...
- Page 5 10.5" 8 SHAFT (harness) FRAMES 1 REED 2 LEASE STICKS 1 BEAM STICK 3 WARP RODS 10.5" 1000 HEDDLES 1 HEDDLE AND REED HOOK 8 5/8” long 6140-9000 1 Black Screwdriver 1 Red Screwdriver 1 Adjustment wrench 10 treadle hooks 10” 10 pegs to lock the treadle hooks TREADLE CORDS 6½”...
- Page 6 Machine bolts 1X 7/16 X 3½" (12 mm X 90 mm) 1" 2" Carriage Bolts 2 - ¼ X 3¼” (6 mm x 80 mm) (F. Cross-Member) 2 - ¼” X 3” (6 mm x 75 mm) (Treadle blocs) 2 - ¼” X 1¾” (6 mm x 45 mm) 4 - 5/16 X 2½”...
- Page 7 Lay the left side on the floor with caution (you can put a piece of cardboard on the floor). Removed the packing material and using three #14 round head screw 2½", affix the base to the left upright and the back post to the base. #14 round head screw 2½"...
- Page 8 ATTENTION: Application of soap to the screws will make their insertion easier. Place right-hand side A straight up beside the wall. Using a 2” (50-mm) round-headed screw no 14, affix lower middle cross-member B to the bot- tom of left-hand side A. The lower middle cross-member has a hole at either end;...
- Page 9 Place the take-up motion handle E, with a 9/16” steel washer, on the right-hand side end of cloth beam F. Note: The ratchet gear is on the right-hand side beam end. The ratchet pawl affixed to the take-up mo- tion handle must be lifted up. Insert the end of cloth beam F into the holes in upper front cross-members G and G` The hole in lower middle cross-member B must...
- Page 10 Using ¼” x 3¼” (6mm x 80mm) carriage bolts, plus ¼” (6mm) steel washer and square nuts, attach front cross-member A to front posts B and B`...
- Page 11 14¼" TO GROUND 12" Wing nut Carriage bolts ¼" - 2¼ ATTACHING THE STABILIZING ASSEMBLY TO THE LOOM Install the rear Stabilizing assembly (A) to the Warp Beam Posts using 6 Round Head Screws #8 - 1” Anchor the hook (B) to the stabilizing post of the loom using 2 carriage bolts ¼” - 2¼” and 2 wing nuts ¼”...
- Page 12 TREADLE SEPARATOR Affix the Treadle Separator Board on top of the back of the side base and secure using 2 #8, 1¼” Round Head Screws. Assemble the treadle set (in or out of the loom) as shown in picture TREADLE SET ASSEMBLY using: Treadle 1 treadle rod 27¾”...
- Page 13 The ratchet pawl Q affixed to the Side Loom must be lifted up while inserting the Jack Box. Slide jack box B along the middle posts A, from bottom to top, and affix it to blocks C using eight 1½” (40 mm) round-headed screws no. 12. NOTE: The 10 screws go in the front bottom of the loom.
- Page 14 Join the “S” hook of the jacks D to the eyelet of the FLOATING lam E. Castle cover Complete the assembly by secur- ing the Castle cover with 4 #12 1½” flat screws. Make sure to screw into the pre- drilled holes of the castle.
- Page 15 Install the treadle cords with the treadle hooks. Using the carriage bolts, steel washers and square nuts, attach the batten sley A (with shuttle race) to the batten swords B. Then affix the batten handtree C to the batten swords B. Install reed D in the slots of batten handtree C and batten sley A.
- Page 16 If the batten does not touch the two bumpers equally, loosen the bolts of the batten sley and batten handtree and exert pressure on the batten centering it in its proper place. Tighten the bolts again. You can install now or just before weaving the treadles springs. After the installation, the treadles will be all at the same height.
- Page 17 Unhook brake treadle cord C from the brake release treadle. Hold circular wire brake shoe D up slightly to the rear of the loom. Insert one end of the warp beam (which has only a metal post) into the left-hand side back post.
- Page 18 Insert the brake end of the warp beam into the hole of the right-hand side back-post. Install the 7/16” X 3½” machine bolt through the right-hand side back post and into the warp beam. Using crank E, tighten the machine bolt into the warp beam.
- Page 19 Using two 2” round-headed screws no 14, affix the breast back beam to the back posts. Join the front “S” hook of the brake lever to the brake loop cord so the tension on the spring will be high enough to lock the warp beam while weaving. The warp beam should turn with some friction clockwise (while standing at the right side of the loom near the brake system) and this is the warping rotation.
- Page 20 FIRST TREADLE TIE-UP Select any treadle and tie the Lams to the Treadles using the 7½” cords supplied with the loom. Use the threading hook to help pass the cord through each hole of the lam. Fig. 24 Threading Hook TREADLE HOOK AND ROCKER LOOP CORD Slide the Treadle Hook through the Screw Eyes and the treadle Cord Loops.
- Page 21 Loop cord screw FIRST SHED When you depress the treadle, Treadle spring the rocker loop cord raises the front of the rocker setting the shafts at the correct Level. See next page for more info on adjusting the length of each rocker loop cord.
- Page 22 ADJUSTING THE SHED (Length of the Rocker Loop cord) Picture 32 The key to a wide clean shed is the proper adjustment of the Rocker Loop Cord. Once you have completed the hookup of the Cords and Springs, start at one end of the Treadle Set and depress each Treadle one at a time noting the position of the bottom Shed.
- Page 23 Thread the 10 yard (9 m) cord through the middle hole of beam stick A. Then pass the two ends (equal in length) of this cord through the middle holes of the warp beam. Continue threading the cord through the warp beam and beam stick A.
- Page 24 Warp beam advance control system Cut the 5-yard (4.5 m) cord in half. One half of this cord laces beam stick A to warp rod B Insert a metal rod into the apron of the cloth beam. Use the other half of the cord to lace this rod to the third metal rod. This system will eliminate excessive warp yarn advance when releasing the brake system at cloth take-up.
Need help?
Do you have a question about the ARTISAT 36 inch and is the answer not in the manual?
Questions and answers