Nortek GoControl GD00Z-4 Installation Instructions Manual

GD00Z-4
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR

Installation Instructions

➌
PRODUCT COMPONENTS
GD00Z-4
STATUS
INDICATOR
POWER
INPUT
JACK
CONNECTION
WIRES
OPTIONAL
ADJUSTABLE
GD00Z-4 MOUNTING
BRACKET
WIRE
TIES
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
TILT
BRACKET
SENSOR
POWER
SCREWS AND
SUPPLY
MOUNTING TAPE
FOR TILT SENSOR
INSTR,INSTL,GD00Z-4 - P/N: 236956 BX1 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000" X 8.500" - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
➊
PRODUCT DESCRIPTION
GD00Z-4 Overview
• A garage door opener remote
command transceiver with built-in
Z-Wave technology.
• Allows remote operation of a garage
door opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve
communications within the Z-Wave
mesh network.
GD00Z-4 Summary of Operation
• GD00Z-4 connects to the garage door
opener's pushbutton wall console
terminals.
• A wireless tilt sensor mounts on the
garage door and reports the door's
position to the GD00Z-4.
• GD00Z-4 responds to Z-Wave
commands from Z-Wave controllers to
open or close the garage door.
• A warning indicator light fl ashes and
a beeper sounds for 5 seconds before
the door begins to move.
• If the door does not completely
open or close, a second open or
close command can be sent after
30 seconds.
• If the door does not completely open
or close after the second attempt,
the GD00Z-4 operation is suspended
until a local garage door pushbutton is
activated.
➍
TILT SENSOR INSTALLATION AND BATTERY
WARNING
To activate the tilt sensor,
1
remove the battery protection pull strip
LIGHT
LINK
BUTTON
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-4
POWER
SUPPLY
RETAINING
BRACKET
The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell
SCREW FOR
POWER SUPPLY
BRACKET
1
To open the case, twist
a small screwdriver
in case slot
PRINTER'S INSTRUCTIONS:
Z-Wave Information
• Z-Wave ® is a registered trademark
of Sigma Designs Inc. and/or its
subsidiaries.
• Z-Wave is an Interoperable two-way RF
mesh networking technology designed
for use with a Z-Wave gateway/
controller and other Z-Wave enabled
devices.
• Replication is the process of copying or
transferring your Z-Wave network from
one controller to another.
• This is a Security enabled Z-Wave
product and must be used with a
Security enabled Z-Wave controller
in order to fully utilize this product. As
such, this device will not respond to
Basic CC commands.
• ASSOCIATION: The GD00Z-4 supports
1 Group with 1 Node. Group 1 must be
assigned the Node ID of the controller
to which unsolicited notifi cations from
the GD00Z-4 will be sent. The Z-Wave
controller should set this association
automatically after inclusion.
2 3
Attach the mounting plate
Snap the sensor onto
to the top panel of the door the mounting plate
ARROWS ON PLATE
& SENSOR POINT UP
"UP"
ARROWS
POST ON
BOTTOM
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
LOW BATTERY REPLACEMENT PLUS SIDE UP !!!
2
Insert the CR2032
battery
into the
transmitter
SLOT
➋
SAFETY NOTES
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors
only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Transceiver must be mounted in
the garage, in sight of the garage door, where the visual
and audible movement warning indicators can be clearly
seen and heard.
WARNING
Do not install the Remote Command Transceiver on
garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment
detection system).
➎
PAIRING (INCLUDING) WITH THE SYSTEM
Note: Plug in the GD00Z-4
near your Z-Wave Controller
for these steps
WALL
OUTLET
GD00Z-4
POWER
POWER
SUPPLY
INPUT
JACK
TO INCLUDE THE GD00Z-4 TO EXCLUDE THE GD00Z-4
INTO YOUR CONTROLLER FROM YOUR CONTROLLER
1 Place your Z-Wave Controller into 1 Place your Z-Wave Controller into
Discovery or Include mode. Exclude mode.
Press and release the link button Press and release the link button
2 2
on the GD00Z-4. on the GD00Z-4.
3 Confirm that the GD00Z-4 was 3 Confirm that the GD00Z-4 was
recognized by your Z-Wave Controller. excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers Refer to your Z-Wave Controllers
instructions for additional information instructions for additional information
on including devices. on excluding devices.
LINK
BUTTON