Sherlotronics RX4-500 Installation Instructions

Defaulting the RX4-500
Note: Please default the unit first before installation.
This will erase any previously programmed factory
test remotes from the memory.
Programming remotes in
1. Default the unit before you begin a new installation. This erases all previously programmed remotes.
2. Press the LEARN switch once to step to relay 1. (1 x beep sounds)
3. Press the button on the remote control a few times to learn in to the RX4-500 (2x beeps sound)
4. Continue to learn in any additional remote controls until all the remotes are programmed in.
5. Press the LEARN switch again to step to relay 2. (1x beep sounds)
6. Repeat Step 3; 4 & 5 until all the remotes are programmed in to each respective relay.
7. Once Relay 4 is programmed, press the LEARN switch once more to step past relay 4 and exit out
of learn mode. (1 x long beep sounds)
Note: The unit can be programmed with up to 80 remotes. When the memory limit has reached its limit the
RX1-500 will auto exit out of program mode. The unit auto exits out of program mode if nothing is received after
10 -20 seconds.
Programming the ON/OFF function
1. Default the unit before you begin a new installation. This erases all previously programmed remotes.
2. Select the 1 sec & 3 sec relay time jumpers respectively.
3. Press the LEARN switch once to step to relay 1 (ON command) (1 x beep sounds)
4. Press the button on the remote control for the ON command. (2 x short beeps sound)
5. Press the LEARN switch again to advance to the OFF command. (2 x beep sounds)
6. Press the button on the remote control for the OFF command. (2 x short beeps sound)
7. Press the LEARN switch again to advance to the next relay channel.
8. Repeat Step 3 - 6 until all the remotes are programmed in to each respective relay.
7. Once Relay 4 is programmed, press the LEARN switch once more to step past relay 4 and exit out
of learn mode. (1 x long beep sounds)
Erasing individual remotes
1. Link the ERASE jumper
2. Press the LEARN switch
Link On
3. Press the remote to be erased
4. Repeat step 2 & 3 for each
remote to be erased.
5. Remove ERASE jumper when
done
Relay time jumper settings
60 Seconds
1 Second 3 Seconds
1sec 1sec 1sec
3sec
3sec 3sec
1min 1min 1min
3min 3min 3min
On/Off On/Off On/Off
Latch Latch Latch
Panic Maglock
Gate &
on alarm release /
garage door
panel beam bypass
automation
Warranty
This product is sold subject to our standard warranty conditions and is warrantied against defects in workmanship
for a period of two years.
Customer Support line: +2711 462 5101 E-mail: technical@sherlotronics.co.za
LEARN
Press and hold for more than
10 Seconds. When the beeping
stops the unit is defaulted.
Wait a few seconds until it re-boots.
Repeat for each remote
to be erased.
ERASE
Press the button
to be erased
Latch/un-Latch
3 Min
On / Off
1sec
1sec 1sec
3sec 3sec 3sec
1min 1min
1min
3min 3min
3min
On/Off
On/Off On/Off
Latch Latch
Latch
Arming &
Siren output
Code 1 = ON
Disarming
or beam
Code 2 = OFF
alarm panels
bypass
English
Installation Instructions - For Service Persons Only
Model No: RX1-500
1 Channel Receiver : 500m Code Hopping
Technical Specifications:
Model:
Encryption type:
Transmission frequency:
Transmission method:
Modulation
Transmission range:
Memory capacity:
Voltage range:
Standby current consumption:
Current consumption all on:
Operating Temperature:
Dimension (lxbxh)
Gross weight:
Features:
Code-Hopping Encryption
20 beeps
1 x Relay output
You must erase
one remote
Normally Open / Closed
at a time.
Weather-proof ABS housing
Frequency stability controlled +/- 75KHz
Order Codes:
1 Channel Receiver : 500m Code-hopping
For more info visit our web site: www.sherlotronics.com
RX1-500
Code hopping
403MHz (local) 433MHz (export)
OOK
AM
500m "Line of sight"
80 remotes
10V to 16VDC
+/-22mA 10%
+/-126mA 10%
-3°C to 49°C
145 x 66 x 40mm
135g
Approvals: * (pending)
This product is approved for use in residential, commercial andlight
Industrial environment and complies with the essential protection
requirements of the R&TTE Directive 1999/EC on the
approximation of the laws of the Member states relating to
electromagnetic compatibility and radio spectrum.
Certifications:
ETSI EN300 220-V2.4.1
ETSI EN301-489-3 V1.4.1
ETSI EN301-489-1 V1.9.2
IEC 60950-1:2005 + A1:2009
RX1-500
III
RX1 - 5 0 0