Tv Operation; Starting Setup - Sanyo DP26671 Owner's Manual

Starting setup

The Auto Setup menu appears the first time you
turn on the TV, and assists you to specify the
Air/Cable setting, and program your channels
automatically.
IMPORTANT: Make sure that the antenna or cable
TV system connection is made!
1
To turn on the TV, press POWER (POWER
indicator on the front of the unit changes green.
It may take approx. 10 seconds for a picture to
appear on screen.). The Auto Setup function
begins.
Auto Setup
TV Location Store
Signal Type Cable
Automatic Search Start
This unit has been preset to STORE brightness
This setting does not qualify under ENERGY
STAR. To reduce brightness and energy
consumption, change setting to 'HOME'. This
setting does qualify under ENERGY STAR.
:Select :Adjust
2
Press ▲ or ▼ to select "TV Location", then press
◀ or ▶ to select "Home" or "Store". This product
qualifies for ENERGY STAR In Home mode
default setting.
NOTE:
• This unit has been preset to STORE brightness.
This setting does not qualify under ENERGY
STAR. To reduce brightness and energy
consumption, change setting to 'HOME'. This
setting does qualify under ENERGY STAR.
• The device may not conform to the ENERGY
STAR standard after Reset is performed or the
Backlight is adjusted.
3
Press ▲ or ▼ to select "Signal Type", then press
◀ or ▶ to select "Cable" or "Air".
4
Press ▲ or ▼ to select "Automatic Search", then
press ▶ or ENTER.
5
Now the "Auto Setup" starts. After the Auto Setup
is completed, the TV channel appears on the
screen.
•
Depending on the reception condition, it may
take from 15 minutes to 30 minutes to complete
memorizing digital cable channels. Please be patient.
NOTE:
• If you press EXIT in the process of "Auto Setup",
the Auto Setup stops and changes to the normal
screen.
• When you make a menu selection, your changes
occur immediately. You do not have to press EXIT to
see your changes.

TV operation

1
To turn on the TV, press POWER.
(POWER indicator on the front of the unit changes
green. It may take approx. 10 seconds for a picture
to appear on screen.)
2
Adjust the volume level by pressing VOL + or – .
The volume level will be indicated on the screen by
green bars. As the volume level increases, so do
the number of bars. If the volume decreases, the
number of green bars also decreases.
56Q0221A_eng.indd 17 56Q0221A_eng.indd 17
3
Set the Signal Type option to the appropriate
position (see "Air/Cable selection" on page 20).
4
Press the Direct Channel Selection (0-9, –)
buttons to select the channel.
(If you press only channel number, channel selection
will be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to select
channel 2, press 2, then press ENTER.
10-99: Press the 2 digits in order. Example, to
select channel 12, press 1, 2, then press
ENTER.
100-135: Press the 3 digits in order. Example, to
select channel 120, press 1, 2, 0, then
press ENTER.
TO SELECT DIGITAL CHANNELS
Press the first 1-3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1,
then press ENTER.
• If a channel is selected with only audio content,
"Audio only" will be displayed on the screen.
• If a channel is selected with a weak digital signal,
"Digital channel signal strength is low" will be
displayed on the screen.
The same program may be available on either
an analog channel or a digital channel. You may
choose to watch either format.
• If a channel is selected to which you have not
subscribed, "Digital channel is encrypted" will be
displayed on the screen.
VHF/UHF/CABLE CHANNELS
Air
VHF
2-13
UHF STD/HRC/IRC
14-69 14-36
37-59
60-85
86-94
95-99
100-135
01
NOTE:
• If a channel with no broadcast is selected, the
sound will automatically be muted.
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.
To select the video input source
To view a signal from another device connected to your
LCD TV, such as a VCR player, press INPUT SELECT,
then press ▲ or ▼ or corresponding Number buttons (0-
7), then press ENTER. You can select TV, Video1, Video2,
Component, HDMI1, HDMI2, PC or DVD depending on
which input jacks you used to connect your devices.
Input Select
0.TV
1.Video1
2.Video2
3.Component
4.HDMI1
5.HDMI2
6.PC
7.DVD
[0-7]:Select
CH /
Press and release CH /
automatically stops at the next channel set into
memory.
For proper operation, before selecting channels, they
should be set into the memory. See "Memorizing
channels" on page 20.
Cable
VHF
2-13
(A) (W)
(AA) (WW)
(AAA) (ZZZ)
(86) (94)
(A-5) (A-1)
(100) (135)
(4A)
. The channel
17
1/8/11 5:31:55 PM 1/8/11 5:31:55 PM