Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Powermatic Accu-Fence
- Page 1 This .pdf document is bookmarked Operating Instructions and Parts Manual ® Accu-Fence and Rail System For PM2000B, PM3000B Table Saws Powermatic 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-2195079B Ph.: 800-274-6848 Edition 2 10/2018 www.powermatic.com Copyright © 2017 Powermatic...
-
Page 2: Important Safety Instructions
20. Make your workshop child proof with padlocks, intended use. If used for other purposes, master switches or by removing safety keys. Powermatic disclaims any real or implied 21. Give your work undivided attention. Looking warranty and holds itself harmless from any around, carrying on a conversation and “horse-... -
Page 3: Kickback
27. Keep hands clear of the blade area. Do not WARNING: Drilling, sawing, sanding or reach past the blade to clear parts or scrap machining wood products generates wood dust with the saw blade running. Never saw and other substances known to the State of freehand. -
Page 4: About This Manual
Additional knowledge can be obtained from experienced users or trade articles. Whatever accepted methods are used, always make personal safety a priority. If there are questions or comments, please contact your local supplier or Powermatic. Powermatic can also be reached at our web site: www.powermatic.com. -
Page 5: Table Of Contents
6.5 Installing guide tube ..........................10 6.6 Mounting Accu-Fence ..........................11 6.7 Side plate replacement ..........................12 7.0 Rail installation on a non-Powermatic Saw ....................13 7.1 Tools required for assembly ........................13 7.2 Installing front rail ............................. 13 7.3 Installing back rail ............................. 14 8.0 Replacement parts ............................ -
Page 6: Accu-Fence Specifications
84 in. (213 cm) The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, Powermatic reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Unpacking
Read the instruction manual thoroughly assembly, alignment, maintenance instructions. See Figures 6-1 thru 6-3. Box 1: Accu-Fence – A Locking handle – B Plastic shims (not shown) Product registration card Operating Instructions and Parts Manual Figure 5-2: contents of Box #2 Box 2: Front rail –... -
Page 8: Set-Up And Assembly (Powermatic Saw)
The following instructions are for installing the Accu-Fence and Rail System on a Powermatic Model PM2000B or PM3000B table saw. The rails should bolt up to the Powermatic saw without any drilling. For mounting to a non-Powermatic saw, see sect. -
Page 9: Installing Wood Extension Table (Optional Accessory)
The optional wood extension table (including optional router table) sits flush against saw table and along inside of rails. The Powermatic logo should face outward. The extension table is not bolted to the saw table; it is bolted only to the rails. -
Page 10: Installing Guide Tube
Use a rubber mallet (or hammer and flat block of wood) to tap extension table up flush against saw table (Figure 6-7). Then tap down extension table at various points along its edge where it meets saw table, until it is level with saw table (Figure 6-8). -
Page 11: Mounting Accu-Fence
Front Rail Space should be 1/32" along entire length of fence Figure 6-14 Turn Accu-Fence upside down and with a rubber mallet (or hammer and block of wood), Figure 6-12 gently tap the side plates to create a height Fasten guide tube to rail from beneath, with greater than 1/32"... -
Page 12: Side Plate Replacement
Cursor position should be checked after installing a new blade. 6.7 Side plate replacement The Accu-Fence is specially designed to save many hours of down-time when side plates need to be replaced. In an operation that can last an entire day with other fences, the Accu-Fence side replacement takes only a few minutes. -
Page 13: Rail Installation On A Non-Powermatic Saw
Place an adjustable square on the table, as shown in Figure 7-3. non-Powermatic Saw The following instructions are for installing the Accu-Fence and Rail System on a table saw other than a Powermatic model. Some drilling is required. 7.1 Tools required for assembly... -
Page 14: Installing Back Rail
Finger-tighten only at this time. The rest of the installation is the same as with a Powermatic table saw. Refer back to sect. 6.4 to mount the optional wood extension table (if applicable) and the guide tube in sect. 6.5, and... -
Page 15: Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1- 800-274-6848 Monday through Friday (see our website for business hours, www.powermatic.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. -
Page 16: Rail Assembly - Parts List
8.1.2 Rail Assembly – Parts List Index No Part No Description Size ....2653031B ....50" PW Rail Set for PM2000B & PM3000B ............... 2653039B ....30" PW Rail Set for PM2000B ................... PM2000B-HK-50 ..Hardware Kit for 50" Rail Assembly (includes #1 thru 9) ........ 1 1 .... -
Page 17: Accu-Fence Assembly - Exploded View
8.2.1 Accu-Fence Assembly – Exploded View... -
Page 18: Accu-Fence Assembly - Parts List
Index No Part No Description Size ....2195079B ....Accu-Fence Assembly for PM2000B ............. 1 ....2195080B ....Accu-Fence Assembly for PM3000B ............. 1 1 ....PM2000B-501 ... Fence Body (only for PM2000B)..............1 ....PM3000B-501 ... Fence Body (only for PM3000B)..............1 2 .... -
Page 19: Warranty And Service
Powermatic sells through distributors only. The specifications listed in Powermatic printed materials and on the official Powermatic website are given as general information and are not binding. Powermatic reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. - Page 20 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.powermatic.com...
Need help?
Do you have a question about the Accu-Fence and is the answer not in the manual?
Questions and answers
how do I install pads to fence?