Advertisement
Quick Links
Advertisement
Related Manuals for Uspa A8
Summary of Contents for Uspa A8
- Page 1 Operating Instruction Manual Thank you for purchasing this USPA bidet seat. You are kindly requested to carefully read this operation. manual for proper use of this appliance. Please save this manual and place it in an easily accessible location. Please register warranty for proper service.
- Page 4 After installation all other servicing should be performed by authorized service representatives. This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire and grounding plug.
-
Page 5: Remote Control
(seat cover) Caution label Deodorizer Power plug Nozzle Side control buttons Heated seat Occupied sensor Accessories Remote Control Mounting bolt (2pcs) (15mm) (8mm) Water supply hose (2pcs) Cone packing (2pcs) Remote control Remote control Bracket Washer (2pcs) Mounting Plate T-valve Screw (2pcs) Plastic anchor (2pcs) - Page 8 Place the mounting plate over each mounting hole. Slide the unit until it clicks into the plate. Insert the mounting bolts through the plate and mounting holes. Slide cone packings and washers onto the bolts and fasten tightly with nuts. While pressing the detach button, pull the unit forward and separate it from the toilet bowl.
-
Page 10: Battery Alarm
Press "Dry" Warm air will come out for 3 minutes. To alter the strength of drying, press the button again. Dry temperature can be adjusted by pressing LOW or HIGH button to 5 levels. Cleansing Press "Cleansing" to clean your posterior. The function will stop in 2 minutes automatically. - Page 11 Massage - Press "massage" to activate rhythmical wash for massage effect when you are using "cleansing" or "bidet". - Press the button again to release this function. Kids - Press "Kids" to change all functions to be suitable for children. It will automatically operate from cleansing(2 min) to dry(3 min) with adequate water pressure and nozzle position.
- Page 12 - This function is useful for public toilets when more than one unit of this product is installed. - To prevent interference among units, main unit and remote control should be set with the same ID. - If there is only one unit in the bathroom, you do not need to set ID. - Initial ID of remote control and main unit are "0".
-
Page 13: User Setting
- Use side control buttons on unit when remote control is broken or its batteries are dead. - Press “Cleansing” or “Bidet” to start. - Press again to stop. Do not use sharp items to press buttons. CLEANSING / STOP BIDET / POWER USER SETTING -Each button can save 2 setting.(Cleansing, Bidet) - Page 14 Do not forcefully push or pull the nozzles, or bend them. It may result in failure. Make sure to use“Stop”button on the remote control. Make sure the occupied sensor is not activated. (Do not sit on the seat or place hands on the seat sensor) Press Front( ) button for 2 seconds to extract the nozzle.
- Page 15 Unplug the power supply cord. Close the shutoff valve. - Not doing so may cause fire. Uphold the appliance and thoroughly drain the water by unscrewing the drain bolt. (Beware of losing the drain bolt) While pressing the detach button, pull the unit forward and separate it from the toilet bowl.
- Page 16 " " - Press again to release the function AC 120V 60Hz 1248W Direct connection to tap water 0.07MPa ~ 0.74MPa 700 (±150)㎖/min 700 (±150)㎖/min 740㎖ Room temp ~ 39℃(102℉) 1200W Thermal switch, Temperature fuse, Floating switch Air temperature Room temp ~ 60℃(140℉) 250W Temperature fuse, Bimetal Room temp ~ 39℃...
Need help?
Do you have a question about the A8 and is the answer not in the manual?
Questions and answers
How do I switch remote from Centigrade to Fahrenheit?