Advertisement
Quick Links
Installation instructions
Troldtekt
acoustic panels K0-S, K0-FS
®
Installed in exposed T35 profiles in removable,
suspended ceiling system
TROLDTEKT
ACOUSTIC PANELS
®
K0-S:
Square edge
KO-FS: Rebate
INSTALLED IN SUSPENDED T35 PROFILES
Installed in exposed T35 profiles in removable, suspended ceiling system September 2010 Page 1
Advertisement
Summary of Contents for Troldtekt K0-S
- Page 1 Installation instructions Troldtekt acoustic panels K0-S, K0-FS ® Installed in exposed T35 profiles in removable, suspended ceiling system TROLDTEKT ACOUSTIC PANELS ® K0-S: Square edge KO-FS: Rebate INSTALLED IN SUSPENDED T35 PROFILES Installed in exposed T35 profiles in removable, suspended ceiling system September 2010 Page 1 ...
- Page 2 STORAGE AND ACCLIMATISATION °C °C Outdoor storage Indoor storage Acclimatisation If it is necessary to store Troldtekt panels If you store Troldtekt panels indoors, you It is important that the Troldtekt panels outdoors, you should protect the panels must remove any packaging, as condensa- are allowed to acclimatise prior to installa- using a tarpaulin or similar. Please note tion could otherwise form within the pack- tion. Acclimatisation means that the that outdoor storage should be as brief aging. Care should be taken to protect p anels must adapt to the temperature as possible and never directly on the stored Troldtekt panels from moisture, and moisture in the room where they are ground. d irect heat and dust. to be installed. COMPONENTS Product name Perimeter angle profile, V300 – 30× 30 mm Cross tee, T60 – 24× 38 mm Main tee profile, B360 –...
- Page 3 INSTALLATION 1: F ix the perimeter angle profiles securely 2: F ix the hangers securely to the struc- Fix the hangers securely to the struc- 3: P lace the cross tees between the main ture above. In order to facilitate tee profiles by inserting the tongues of to the wall with a max. spacing of 300 i nstalling the Troldtekt panels, the the cross tees into the slots of the main mm. Additionally, fasten 50 mm from profile end at joints, abutments and hanger should be min. 200 mm long. tee profiles, spaced at 150 mm. (See fig. endings. (See figs. A and B). Hang the In case of increased loads from e.g. E). When you have installed the profiles, main tee profiles in parallel at 600 mm, lighting fixtures, the hanger spacing check that all hangers are secure. Adjust with hanger points at max. 1200 mm. should be reduced. Fix heavy fixtures if necessary. Now lay the Troldtekt There should be max. 300 mm from the etc. to the structure above. Cut the panels in the grid. main tee profiles at the wall and en- transverse wall to the first hanger. The sure that the slots are placed correctly 4: Please note: When installing 600 × 600 main and cross tees should lap on the perimeter angle profiles.
- Page 4 NOM. LENGTH WEIGHT NO. OF PANELS PERPENDICULARITY PLANENESS (mm) (mm) (mm) (kg/m (per pallet) (mm) (mm) ≤ 2 ≤ 3 1200 (+/- 1.5) (+/- 1) (+/- 1.5) (+/- 10%) *600 × 1200 mm pallet FURTHER INFORMATION On www.troldtekt.com you can read more installation instructions and see the about Troldtekt products. You can also complete range of Troldtekt installation download the most recent version of these instructions. Troldtekt A/S Sletvej 2A DK - 8310 Tranbjerg J Tel. +45 8747 8100 Fax +45 8747 8111 info@troldtekt.dk www.troldtekt.com...
Need help?
Do you have a question about the K0-S and is the answer not in the manual?
Questions and answers