Wiring Installation Instructions; Installation Instructions - Koso RX2N GP Manual

2 -1
Wiring installation instructions
,.-­
r-
r-=
~
r-­
(~
.....
f ­
~
d
---.J
D
I
Gray
7
L
turn signal (+
12V) ~
----l
White
7
R turn signal
{+
12V]
I ,--...o{::::b...d:::J--------I
---1
Violet
7
EOBD
nght (
+ )
I
~
Orange
7
OIL
!Igtlt (-)
I
~
Blue
7
Neufial llght (-)
I
---l
Meter (Accessory 1)
I
Brown/ RPM wire please
connect It to the suitable
position according to the
models.
W
I RPM wire setl
c:::::::$
fl:::
I
Ground
f-
l!::m(Q)
~
__
~~~ ~~~~~~~~a
Fuel
.1..
The fUel sensor Is electronic type. please don't
parallel connect/on
w/tt)
tile original· oftlerwlse
tile fuel gauge won't display.
The wrong In,'a/kltlon of'he fuel wiring may
cau••
the
m.ter
break.
flMa
The temperature wm disappear
If
you don't Instan & connect
ffle
temperatUre sensor with
the
meter.
U1!Jlj
When connecting the power wiring. please follow the Instruct/on. "you connect the red & brOlVn wiring In parallel will cause the meter work Improperly.
I
~ The RPM wire Instal/atlon
A. Please wrap the RPM wire
at
least 5 times around the spark plug.
A1. Please use tope to fix the RPM (Type A) wire onto the spark plug wire ,
A2. Please use tope to fix the RPM wire (Jype A) on the spark plug cop.
A3. Please use tope to fix the RPM wire (Type A) on the coli positive pole wire. For
some
models with the coil negative wire, please tope
the RPM wire (Type A) on the negative wire to get the RPM signal. (For example, the YAMAHA V-max 1200)
B. Please connect the RPM wire (type B) to connect to the Ignition col/ positive pole.
B1. Please wrap the RPM wire (type B) on the spark plug wire by connecting the mole and female connector.
C. Please connect the RPM wire (Type A) to the pick up.
D. Please parallel the RPM wire (Type A) with the original tachometer signal wire (This method Is oval/able only when the orIgInal
speedometer
comes
with
a
tachometer on
It.
You could get the RPM wIre InformatIon from the servIce manual of your bIkes.)
E. For the models
comes
wIth the new IgnItIon colt please wrap the RPM wIre (Type A)
at
least 5 tImes around the spark plug
as
the
above drawIng.
F. Please use the method mentioned above to Install the RPM wire, and then connect the ground wire to the frame body or the
engine. (Please make sure that the ground Is a good ground.)
For multi-Ignition models, we will suggest you
to
get the signal on the first Ignition.
The best signal source will be In order as D>C>B>A, we w111 suggest you to check different ways /fyou have problems to get the
RPM signal.
2 -2
Installation Instructions
When installing, please follow the process
1. M6 or M8 screw X 2 (Accessory 11. 18)
2.M6 or M8 alumInum screw bush X 2 (Accessory 19.20)
3. Brocket (Accessory 14}
4.M6 or M8 gasket X 2 (Accessory 21
. 22)
5.Handle bar brocket
Ul!llI
You could also Install It (meter bracket) on the orIgInal
meter brocket.
6.MS screw X 3 (Accessory 15)
7,M5 gasket X 3 (Accessory 16)
8. Meter (Accessory 1)
9,
Meter broc ket mIcrO-ad ustment screw
U1!Jlj
You
cou
d choose the angle first and then use the
screw to fix the angle.
U1!Jlj
The handle bar brocket screw and screw hole will
dIffer dependIng on dIfferent model. We suggest you
to use the oddltronal assembly (Item 1.2.4) to fit It.
wh015ba001