Related Manuals for Winflo WH101
Summary of Contents for Winflo WH101
-
Page 1: Installation Instructions
Range Hoods Installation Instructions, Maintenance, Use and Warranty INSTRUCTIONS FOR MODELS: WH101, WH102, WH104, WH106, WH107, WH114, WH117... -
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE FOLLOWING: ➢ Use this unit only in the manner intended by the manufacturer. If you have questions, please contact the manufacturer. ➢ Before servicing or cleaning the unit, switch the power off and turn power off at the electrical panel and lock the service panel. -
Page 3: Location Requirements
LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. Canopy hood's location should be away from strong draft areas, such as windows, doors, and strong heating vents. Cabinet opening dimensions that are shown must be used. -
Page 4: Ventilation Requirements
VENTILATION REQUIREMENTS General requirements ➢ Range hoods must be ventilated to the outdoors, except for non-vented (recirculating) installations. ➢ Do not ventilate the range hood into an attic or other enclosed areas. ➢ Do not use 4” (10.2 cm) laundry-type wall caps. ➢... - Page 5 INSTALLATION DIMENSION RECOMMENDATIONS For Island range hoods: A. Countertop Height. B. Hood height from ceiling to bottom of the range hood filter surface: D-A-C=B. C. 24” minimum from cooking surface up to 36” maximum for Electric/Induction range tops. 27” minimum from cooking surface up to 36”...
- Page 6 INSTALLATION INSTRUCTIONS for Island Range Hood Parts supplied (Note: The fasteners included may not be suitable to your ceiling structure. Please check with the installer on proper fasteners to be used based on the material makeup of your ceiling) A. Range Hood B.
-
Page 7: Installing The Range Hood
Inner Outer Parts not supplied ➢ Duct tape ➢ Preinstalled ventilation system and ductwork ➢ Preinstalled outside duct cap or weatherproofing Installing the range hood This installation is for mounting the product to a ceiling. Ensure your ceiling has the proper support to hold the range hood weight. -
Page 8: Mounting Bracket Holes
4. Find the center of the ceiling where you are installing the range hood and trace a 6” or 8” circle depending on model. You can use the ceiling mounting bracket (J) to help trace your cut out mark. The ceiling mounting bracket is larger than the 6”... - Page 9 support brace, reach your hand through the ceiling hole and hold the support brace in place. You may wish to further brace the wooden support braces to the joist by entering your ceiling and adding additional screws. Front of range hood 8.
- Page 10 9. Attach the (4) upper support frame brackets (E) to the ceiling mounting bracket (J). Each support bracket will use (4) #6 X 3/8 SM Screws (I). 10. Measure the distance that the bottom of the range hood will be from the top of your range (see page 5 for reference).
-
Page 11: Mounting Brackets
One-piece seamless stainless-steel ducting Two-piece seamed stainless-steel ducting Note Seam For one-piece seamless stainless-steel ducting follow steps 12 through 18. For two-piece seamed stainless-steel ducting go to steps 19 through 25. 12. Slip inner duct up through the support frames and over the ceiling mount bracket. Be sure the duct slides over the (2) mounting brackets on each side. - Page 12 15. Place the range hood underneath the support frames and align the holes of the support frame to holes in the range hood. Warning: This will take at least two people. Screw in (4) #6 X 3/8 SM screws through the support frames into the pre-aligned holes in the range hood on all four corners.
-
Page 13: Mounting Clips
19. Detach the inner duct cover (H) by removing the (2) set screws near the upper middle of the attached duct. Inside the duct, there are tongue and groove clips for stability. Lift on side of the duct to detach. 20. - Page 14 23. Detach the outer duct cover (H) by removing the (2) set screws near the bottom middle of the attached duct. Inside the duct, there are tongue and groove clips for stability. Lift on side of the duct to detach. 24.
- Page 15 INSTALLATION of FILTERS for DUCTLESS (RECIRCULATING) MODE IMPORTANT: If you are choosing the ductless/recirculating mode do not install the duct exhaust hose (I). 1. Unplug the power cord. 2. Remove the filter panel(s) located at the bottom of the range hood. 3.
-
Page 16: Fan Operation
OPERATING INSTRUCTIONS Note: There are different operating instructions based on the control panel for your model. Please choose the operating instruction for your unit. Powering on/off and Settings: Lamp Timer Minus Clock Plus Power/Standby ➢ Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it. ➢... - Page 17 Powering on/off and Settings: Lamp Timer Clock Power/Standby ➢ Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it. ➢ Power/Standby: When the range hood is in the “original” state, touch this button. It will enter the standby mode.
- Page 18 Lamp Timer Minus Plus Fan Power/Standby ➢ Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it. ➢ Power/Standby: When the range hood is in the “original” state, touch this button. It will enter the standby mode.
- Page 19 Powering on/off and Settings: Timer Lamp Clock Fan Speed Power/Standby ➢ Lamp: Press the lamp display one time to activate the light, press the lamp display again to deactivate it. ➢ Power/Standby: When the range hood is in the “original” state, touch this button. It will enter the standby mode.
-
Page 20: Care And Maintenance
CARE and MAINTENANCE Cleaning IMPORTANT: Clean the hood and panel filters frequently per the following instructions. Replace the panel filters before operating hood. Exterior Surfaces To avoid damage to the exterior surface, do not use steel wool or soap filled scouring pads. Always wipe dry to avoid water marks. - Page 21 1. Disconnect the power cord to ensure unit does not turn on. 2. Remove filters. 3. Reach behind the light and push towards you until the light pops out. A screwdriver may be needed to push out light in some models. 4.
-
Page 22: Limited Warranty
It is the consumer’s responsibility to determine local building code. Please write or contact us at: Winslyn Industries, LLC 1232 Hardt Circle Winpro® Sinks Winflo® Range Hoods Bartlett, Illinois 60103 Email: support@winslyn.com Winette® Bathroom Vanities...
Need help?
Do you have a question about the WH101 and is the answer not in the manual?
Questions and answers
the control panel is flashing. which will do anything. can you help ?