Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.
9. If this product fails to operate normally, contact the store of purchase or your nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 10.
Before Usage This is a basic instruction manual for the SCC-C6475(P) user. It contains all the instructions needed to use the SCC-C6475(P) from a simple introduction of the control locations and functions of the SCC-C6475(P) to installation methods in the set up menu. We recommend all users of the SCC-C6475(P) from the advanced user who has used similar cameras before to the general user to read the instruction manual before using.
4. ZONE SET ...4-17 - PRIVACY ZONE...4-17 - STYLE ...4-17 - BLANK ALL ABOVE...4-18 - BLANK ALL BELOW ...4-18 - PRYVACY ZONE MAP3 ...4-18 - SET ZONE AREA...4-19 - SET ZOOM...4-20 - REVERSE ...4-20 - EXIT ...4-20 - ZONE DIR SET/ZONE AREA SET ...4-20 - ZONE DIR SET ...4-21 - ZONE AREA...4-21 - LOCATION ...4-22...
SCC-C6475(P) Introduction SCC-C6475(P) is a zoom lens built in smart dome camera which provides you with the best monitoring function in connection with CCTV at banks or companies. The SCC-C6475(P) is a high quality surveillance camera using x22 zoom lens and digital zoom IC, it can catch clear images up to 220 times.
Setting communication Protocol Use number 1~4 PIN of SW704 to set communication Protocol. PIN1 PIN2 PIN3 PIN4 A : SAMSUNG HALF Comp B : SAMSUNG FULL Baud Rate Setting Use PIN 5 and 6 of SW704. SW 704 BAUD RATE...
Factory Default It recovers the whole setting of SCC-C6475(P) to the factory default. There are two Factory Default methods as follows. (1) Using the Factory Default in the Reset page Refer to 5. Setting and changing the function (System - Reset) in Chapter 3 Network menu Overview.
Before Installing Checking Package Contents Please check that all components listed below are included in the package: SCC-C6475(P) Owner’s Instructions Screws Installation CD Cover Body RJ-45 CROSS LAN CABLE To install and use the SCC-C6475(P), the following cables should be prepared.
Cable Connection 1. First, connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT) 2. Then, connect the other end of the connector to the Video Input Terminal of the monitor. 3. Adjust the power select switch (110 V or 220 V) after verifying the power to connect SCC- C6475(P).
Page 13
3) INDOOR HOUSING (SHG-120) This housing is used for installing the IP SmartDome Camera to an indoor wall or a ceiling. 4) OUTDOOR HOUSING (SHG-220) This housing is used for installing the IP SmartDome Camera to an outdoor wall or a ceiling. 5) CEILING MOUNT ADAPTOR (SADT-100CM) This adaptor is used for installing the indoor housing or the outdoor housing for the IP SmartDome Camera to a concrete ceiling.
Installing the Camera 1. [Figure 1] Install the structure on the ceiling. (Refer to Installation reference for the Length of the structure) * Built in by the builder of the structure [Figure 1] 2. Make a hole in the ceiling where the camera will be installed. (The hole should be about ø185) 3.
Chapter 3. Network Manual Overview In this chapter, we will check how to install the IP Setting of SCC-C6475(P) and operate the camera connecting with network by using the camera access program, and also check various features and usage. Smart Viewer for ProCam for Web-browser operates normally with Microsoft Internet Explorer 5.0 and above.
Page 17
1. Execute the IP installer program and the MAC Address and IP Address list of SCC-C6475(P) cameras connected to the IP router will be shown. SCC-C6475(P) IP’s basic value is set as ‘192.168.1.200’ when shipping. MAC Address of each SCC-C6475(P) is indicated at the back of the camera holder, please check when you sort the camera.
Page 18
Log in at SCC-C6475(P) and the main screen that user can see images appears. After checking if the camera image works well, click the setup mode button in the right up side of the main screen. Move the SCC-C6475(P) setup mode to the Basic Configuration Check if the setting value that user has entered the setting value by using the IP Installer program in the IP Configuration item is saved safely.
Page 19
IP router Port Forwarding setting can be designated at the Application & Gaming Port Range Forward page. As the Example in the figure, designate the TCP and UDP Port to the SCC-C6475(P) camera that is connected to the IP router. Each port that is set to the IP router should be set to the Port number that is set at the SCC-C6475(P) IP setup page.
Page 20
Execute IPinstaller.exe program in the user’s Local PC to set the SCC-C6475(P) IP connected to the IP router. 1. Execute the IP installer program and the MAC Address and IP Address list of SCC-C6475(P) cameras connected to the IP router will be shown. SCC-C6475(P) IP’s basic value is set as ‘192.168.1.200’...
Page 21
Accessing SCC-C6475(P) by using the internet browser, Log In page as follow appears. User ID to Log In is set to a basic value ‘root’ when it was shipped and the password is ‘4321’. Log in at SCC-C6475(P) and the main screen that user can see images appears.
Page 22
In case of connecting more than 2 cameras to an IP router 1. Set each SCC-C6475(P) Port differently. Example) No.1 SCC-C6475(P) – RTSP Control port: 554 TCP Streaming port: 555 UDP Streaming port: 8000 (8000~8009) Upload port: 556 No.2 SCC-C6475(P) – RTSP Control port: 557 TCP Streaming port: 558 UDP Streaming port: 8010 (8010~8019) Upload port: 559...
Page 23
And assign the user PC’s window network setting as following example. Example) IP: 192.168.1.201 Subnet mask: 255.255.255.0 Gateway: 192.168.1.1 Execute the IPinstaller.exe in user PC and verify the IP, Subnet Mask and Gateway connected to the SCC-C6475(P). If the indicated content in the camera list is not the same as follows, fix the setting as the follow Example.
Page 24
Move the SCC-C6475(P) setup mode to the Basic Configuration Assign IP Type as ‘Dynamic IP’ in the Connection Configuration item, if the user uses SCC-C6475(P) by connecting the ADSL modem, assign Connection type as ‘ADSL Modem’. If the user uses SCC-C6475(P) by connecting the Cable modem, assign the Connection type as ‘Cable Modem’.
4) In case of connecting the camera in the intranet (LAN) INTERNET SCC-C6475(P) SCC-C6475 Fire Wall Local PC DDNS Server (Data Center, KOREA) If the user install to use the camera in the LAN environment such as intranet in companies, assign the camera IP by using the Local PC IPinstaller without any specific setting.
3. Log In. 1) Drive the Internet Explorer and then enter the IP address (Example: http://192.168.2.75) of the camera or DDNS address (Example: http://cff0f54.websamsung. net) and move, log in screen as follows will be displayed. DDNS address consists of a combination of 6 digits from the back of MAC Address of SCC-C6475, a lower case letter ‘c’, ‘m’, or ‘p’, and the domain name which is websamsung,net.
Logo Displays the logo image set at the Setup ➔ Layout Samsung electronics logo is set as the initial state. If the logo link is set, clink the logo image and the linked address screen will be displayed. Video Format Displays the information of the image format(MJPEG/MPEG4) that is being shown.
Screen Capture Manual Alarm Save the image that is being shown with JPEG or BMP format. - Saving route: C:\Program Files\Samsung\Smart Viewer for ProCam\ Capture(saving route or file format can be changed in Setup Alarm Reset - File name: yy/mm/dd_hh/mm/ss_camera name.bmp (Example: 20050317_144605_IP SmartDome Camera.bmp)
❖ Image screen adjustment. Zoom In Menu 8 direction key Enter Preset AutoPan 8 direction key It moves the screen position to directions including UP, DOWN, LEFT, and RIGHT. Press the button to move the screen, remove the button to stop. Enter Enter function will be operated when Menu on mode.
Page 30
Video Source : NTSC / PAL(Display the entered image of Camera.) Video Format : Support MJPEG / MPEG4 Resolution - 4CIF (NTSC: 704x480, PAL: 704x576) - VGA (640x480) - CIF (NTSC: 352x240, PAL: 352x288) Frame Rate - CIF: Support up to 30 frames. - 4CIF / VGA: Support up to 25 frames.
2. If the camera is installed over the internet assigned to Dynamic IP - Select IP Type as Dynamic IP. - If the camera is installed directly over the ADSL modem, select connection type as ADSL Modem or Cable Modem. (In case of this, be sure to set the ADSL connection ID and Password).
Camera Log In Camera Display the information about Log In camera and able to set the camera name and Sequence. Camera List Display the camera list that the user added and able to add up to 30 external camera. Insert / Modify - Able to add or modify the camera.
❖ Setting the system Status Display the user IP accessing the system. - This page maintains the recent information to refresh every 5-second. 3-37 Date/Time Able to set the current system time by receiving it from the NTP server Time - Set the time synchronous with NTP (time server) User should input the NTP server IP.
IP Filter Setting the IP Filtering as Enable, Only registered user in the IP list can access. Up to 10 IP can be input in the accessible IP list. 3-39 Display the log information recorded the system modifying events with time. log specifics : User Log In / Video Configuration Change / System Time Change etc.
Software Update Update the network related system software. Procedure 1) Select the distributed file for updating SCC-C6475(P). - File name is provided as a format of SCC-C6475(P)-V1.1-20050531.tgz. - Software update supports only the update file that has the certain file name.
Save : Compress the current setting of the system as cfg.tar and save it in client PC. The route to save is C:\Program Files\Samsung\Smart Viewer for ProCam\Download\cfg.tar Load : Load and apply the saved setting file in client PC (cfg.tar) to the system.
3) Overlay image coordinate - Adjust the image location by setting the adequate value. 4) Select image - Select the overlay image desired to use. - Click the “Remove” button and the selected image will be deleted. 5) Upload new image - Click the “Search”...
Screen Look Banner Select the image to use Banner in ‘Select existing image’ or type url in ‘External’ and check the Banner check box Banner Link Type the url to use for Banner Link and check the Banner Link check box. Logo Select the Image to use Logo in ‘Select existing image’...
❖ Alarm Transfer Setup Set SMTP, FTP to transfer the image in alarming. Transfer Image Setup - Set the image file name to transfer. (Max. 16 characters) - Able to add alarm event name, time information to the file name as a value- added information.
Active Time of Transfer - Able to set the time limit for the alarm image transfer. - In case of setting Always, image will be transferred whenever alarming. - In case of setting Only Scheduled Time, image will be transferred only the defined date and time for the related alarm even when alarming.
4. ALARM AUTO SET Setting to execute the Pattern functions or not when Alarm inputs. When Alarming, stays at the Preset location while Dwell Time set as Preset confront to each Alarm and the Alarm connected to the Pattern will execute the Pattern function continuously.
1. RTP (Real Time Streaming Protocol): International standard protocol to transfer the multimedia data such as voice or image in a high speed by using the UDP 2. TCP: Protocol used in a normal network environment that needs transmission reliability. Connection structure that is always connected to the receiver so the reliability about transmission is high, but it is limited to transfer the massive data in real time with a high speed.
6. Network Terms Definition A computer network that spans a relatively short-distance area. It makes possible to communicate between machines such as various computer and OA machines by connecting the high-speed communication line to the various computer and OA machines. xDSL A common designation of digital subscriber’s line that makes the acronym data communication possible by phone line.
Structure of the Setup Menu CAMERA SET CAMERA ID ON.../OFF V-SYNC INT/LINE... COLOR/BW COLOR/BW.../AUTO... MOTION DET ON.../OFF ZOOM SPEED 1/2/3/4 DIGITAL ZOOM OFF/X2~X10 EXIT QUIT/SAVE/PRESET VIDEO SET IRIS ALC.../WDR... SHUTTER OFF/1/100(1/120)~1/1OK/AUTOX2~X160 OFF/LOW/HIGH MOTION S.SLOW/SLOW/NORM/FAST/F.FAST WHITE BAL ATW1/ATW2/AWC/MANU... ON/OFF FOCUS MODE AF/MF/ONEAF SPECIAL EXIT...
❈ If the power is turned off after PRESET, AUTO PAN, SCAN, PATTERN function is activated and no other control is made, camera will do the same function after the power is turned on. ❈ Menu setting is available only when tilt position is under 90°. When tilt position is over 90°...
COLOR/BW In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter. In a poor illumination environment, the IR filter is turned off in the BW mode the its sensitivity increases as high as a black and white camera. On the other hand, the IR filter is turned on and the sensitivity decreases in the COLOR mode.
ZOOM SPEED In the ZOOM SPEED menu you can select the speed of the ZOOM Key (Tele/Wide). Use the [Left] or [Right] keys in the ZOOM SPEED menu to select the speed. 1 : Slowest speed 2 : Low speed 3 : High speed 4 : Fastest speed DIGITAL ZOOM...
- LEVEL 1 : Controls the shutter speed while WDR operates. - LEVEL 2 : Controls the whole brightness while WDR operates. - FLIKERLESS : This is for preventing flicker on the screen when NTSC system is used in 50HZ power supply region and PAL system is used in 60HZ power supply region.
WHITE BAL Lights are generally denoted as color temperatures and expressed in Kelvin (K) units. The general light color temperatures are shown below. 10000K Blue sky 9000K Rainy 8000K Cloudy 7000K 6000K Sunny 5000K 4000K 3000K Halogen lamp 2000K Candlelight 1000K 4-12 You can select one of four modes for white balance adjustment as follows:...
FOCUS MODE In the FOCUS MODE MENU, the Focus method can be set to AF, MF, or ONEAF. - AF : With AUTO FOCUS MODE, you can monitor the screen continuously and it will focus automatically. While moving the zoom keys, it will automatically focus so FOCUS key input is not necessary.
POSITION SET From "POSITION SET..." press [ENTER] to get into the PAN/TILT, FOCUS/ZOOM SET screen to set the PAN/TILT location and FOCUS/ZOOM condition then press [ENTER] to return to a higher menu. PRESET ID This is the ID set up function for each PRESET. It can be set up to 12 characters using the left, right, up, and down keys.
BLANK ALL ABOVE The available angle for setup ranges from OFF/0/-10 to -90 and the area above a set angle will be regarded as the ZONE area. BLANK ALL BELOW The available angle for setup ranges from OFF/0/-10 to -90 and the area below a set angle will be regarded as the ZONE area.
SET ZOOM Press [ENTER] at the “SET ZOOM...” position to enter the ZOOM setup screen. After ZOOM setup, the PRIVACY ZONE function will be in action only at the higher magnification than the Zoom magnification as set. PRIVACY ZONE SET 0 SET ZONE AREA ON...
LOCATION The “LOCATION...” menu designates the left/right LIMIT positions of ZONE AREA. Enter the setup screen to move PAN, then select a start position and press [ENTER]. Move PAN again to select a end position and press [ENTER]. Now, ZONE AREA setup is complete.
DIRECTION This sets up the movement direction of the START to END location (PAN location standard) "RIGHT " : "LEFT " : ENDLESS This is a 360-degree rotation function that stops for the DWELL TIME only in the START and END positions without running between the START and END positions.
AUTO PLAY AUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when there is no camera action after AUTO RETURN finishes. (AUTO SET) AUTO PAN 1... ➜ PATTERN 1... SCAN 1... Press AUTO PLAY [Enter] AUTO RETURN This menu sets up the time during which AUTO PLAY repeats. AUTO PLAY This function sets up the motion which will be repeatedly performed by SCC-C6475(P) whenever the time set by AUTO RETURN elapses.
AUTO SET This menu designates what to do at the time of ALARM input. Once an alarm is given, the camera will shortly move to the PRESET position corresponding to the respective alarm as follows. PRESET1 to ALARM1 PRESET2 to ALARM2 PRESET3 to ALARM3 PRESET4 to ALARM4 PRESET5 to MOTION...
* SCC-C6475(P) has two FANs inside for preventing overheating. If FAN doesn't work properly, messages below will be displayed. In those case, replace the FAN. - CAMERA FAN ERROR ! : This message is displayed when the FAN which is connected with camera of SCC-C6475(P) does not work properly.
Installing the IP router Setting the IP sharing setting Example (Linksys model WRT54G) 1. LOGIN 1. Open the internet explorer window and enter the http://192.168.1.1 in the address and press enter. 2. User Name: Empty Type Password: admin 3. Press the “OK”. 2.
Page 61
3. Set the Time zone 1. Select the “Time Zone”. 2. Press the “Save Settings”. 4. Verify the Connection state. The way to verify the setting state is as follows. 1. Press the “Status”. 2. Verify the data below Internet Configuration Type. 3.
Page 62
Setting the IP router Example (Netgear model RP614v2) 1. Access 1. Open the internet browser and enter http://192.168.0.1 in the address and press enter. 2. User Name: Enter the “admin”. Password: Enter the password 3. Click the “OK”. 2. Setting the internet connection 2-1 ADSL 1.
Page 63
2-3 Static (Fixed) IP 1. Select the “Basic Settings” of Setup Wizard. 2. Select “No” in case of using Static (Fixed) IP. 3. Select the “Use Static IP Address:. 4. Network Properties ➀ Enter IP Address : IP* ➁ Enter Subnet Mask : Subnet Mask* ➂...
Page 64
1. Select the Port Forwarding in Advanced. 2. Port forwarding (HTTP) ➀ Press “Add Custom Service”. ➁ Service Name : Enter HTTP ➂ Start Port and End Port : Enter 80 ➃ Server IP Address : 192.168.1.2 ~ 255 ➄ Select “Enable”.
Page 65
3. First screen 1. Press the “Next” button. 4. Password for Router 1. Enter the new password to change the password when accessing the router. 2. Press the “Next” button. 5. Time zone 1. Set the time zone that is suitable for user. 2.
Page 66
1. In case of using Cable, press the “Back” button. 2. Select “Dynamic IP Address”. 3. Press the “Next” button. 4. Enter “MAC Address” in the bottom of the router and press the “Clone MAC Address” button. 5. Press the “Next” button and move to the 7th step. 6-3 Static (Fixed) IP 5-14 1.
Page 67
10. Checking the Connection This step is for checking the connection status. 1. Select “Status”. 2. Select “Device Info.”. 3. Check the information of WAN part. If Disconnected, press the “Connect” button and retry to access. If it is unable to keep connecting, retry to go back at first (access).
Product specifications SCC-C6475 Items Contents Product Type - Zoom lens single body WDR IP SmartDome CAMERA Power Input - AC 24 ± 10% (60Hz ± 0.3Hz) Power Consumption - 25W Broadcasting Type - NTSC STANDARD COLOR SYSTEM Image Device - 1/4 inch WDR compatible Exview HAD CCD Effective Pixels - 768(H) x 494(V) Scanning Mode...
Page 69
Cautions • The copyright of the manual belongs to Samsung Electronics Co., Ltd. • Without the permission of Samsung Electronics it cannot be reproduced electronically, mechanically, audibly, or by any other method. • This manual will be modified according to product enhancements.