Advertisement
Quick Links
Cooper Ottoman King Bed
Assembly Instructions
Before you
Start, here
are some
helpful
advices.
Revision number 1/1
1. We suggest you spend a short time reading through this leaflet and then follow
the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you
have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the.
Assembly should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children's reach.
In the unlikely event that this product has missing or damaged parts, please call
03442 920000 to obtain spares
Advertisement
Related Manuals for DREAMS Cooper Ottoman King Bed
Summary of Contents for DREAMS Cooper Ottoman King Bed
- Page 1 Cooper Ottoman King Bed Assembly Instructions Before you 1. We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions. Start, here 2. If you follow the instructions carefully the end result should be worth the effort.
- Page 2 PARTS Fittings M8×20mmx16pcs M6×25mmx12pcs M8×30mmx6pcs M6×40mmx18pcs M4Allen key × 1pc NO. PART LIST (1) HEADBOARD M5Allen key × 1pc (2) FOOTBOARD (3) SIDE RAILS ( R&L ) 11Spanner × 1pc (4) BOTTOM BOARDS (5) GAS LIFT ( R&L ) (6) SIDE RAIL SUPPORT M8 Washer x22pcs (7) RAILS ( R&L ) (8) CENTER RAIL...
- Page 3 ASSEMBLY (1). Use bolt (A), Washer (I) to fix STEP 1 the Side rails 3 to Headboard 1 and Footboard 2 by using Spanner ( F ) . MAKE CERTAIN THE BED IS SQUARED UP, AS SHOWN ON THE RIGHT. Once all four corners are located, make sure the bed is still square as in the sketch, then tighten all the...
- Page 4 ASSEMBLY (1). Attach Bottom Boards 4. STEP 2 Revision number 1/1...
- Page 5 ASSEMBLY (1). loosen the nut, then fix the gas lift. STEP 3 (2). Use bolt (B), Washer (J) to (2). fix the GAS Lifts 5 to Side Rail ROUND HOLE 3 by using Allen key( E ) . Bolts fixing should be in order sequence: fit the round hole first, then fit others.
- Page 6 ASSEMBLY 1). Use bolt (B)(D), with Washer (J) to fix the Center Rail STEP 4 8 9 to Tubing Slats 10 by using Allen key( E ) . 2). Use bolt (D), with Washer (J) to fix the L&R Rails 7 to Tubing Slats 10 by using Allen key( E ) .
- Page 7 ASSEMBLY STEP 5 (1). Use bolt (D), Washer (J) to fix the slat frame to GAS Lifts 5 by using Allen key( E ) and Spanner ( H ) . Bolts fixing should be in order sequence: fit the round hole first, then fit others.
- Page 8 ASSEMBLY (1). Insert Slats 11 to Side Cap (L) & Centre Cap (M) , afterwards STEP 6 insert the Cap to the holes of 2 x L&R Rail 7 , Center Rail 9 Revision number 1/1...
- Page 9 ASSEMBLY (1). Attach the Fabric Pull Handle 12 at the end of slat STEP 7 frame, see picture beside Revision number 1/1...
Need help?
Do you have a question about the Cooper Ottoman King Bed and is the answer not in the manual?
Questions and answers