Related Manuals for HRS MXR
Summary of Contents for HRS MXR
- Page 1 HARMONIC RESOLUTION SYSTEMS MXR AUDIO STAND The Foundation of Great System Performance...
- Page 2 Please read this manual completely prior to assembly and use of your MXR Audio Stand. It contains instructions necessary for proper assembly, use, and care of this system.
-
Page 3: Safety Instructions
Safety Instructions IMPORTANT WARNINGS! Do not place any tall objects on the top shelf of the MXR Audio Stand. A tall object is any object with a height that is greater than the length of the isolation base. A tall object is also any object that has a height greater than its own width or length. -
Page 4: Set-Up Instructions
Set-Up Instructions The MXR Audio Stand consists of a frame structure and the isolation bases that support each component. The standard three and four shelf frame structures come in three boxes. Each box will be marked with the model number starting with MXR. - Page 5 Lift the panel out of the crate by lifting vertically at each end (see Photo 2). Move the panel and packing material directly to your damage free work surface. Once at the work surface, remove and save the two fitted foam end support cushions. Then open the protective paper covering the panel to expose the unit for assembly.
- Page 6 Photo 7 The HRS logo is machined into the center of each brace. Locate the HRS logo on the brace and orient it so that when the stand is upright on its feet, the logo will be in correct orientation.
- Page 7 Repeat the panel brace installation procedure for the second brace at the top of the panel (see Photo 11). Orient the HRS logo so that when the stand is sitting on its feet the HRS logo will be right side up and in proper orientation. Make sure that all eight screws are completely installed on each of the two panel blocks (16 screws total) prior to moving to the next assembly process.
- Page 8 Please follow the same procedure as noted for un-wrapping the first panel. Note: If assembling an MXR frame that consist of more than two panels then install center panel (isolation base brackets on both sides) at this time as the...
- Page 9 Photo 16 Squaring the MXR Frame - It is now time to torque all of the screws in the two brace assemblies. We recommend using a long level to complete this process. Place the long level across the top or bottom of the frame assembly (see Photo 17 &...
- Page 10 When the proper location has been achieved, torque all 32 of the 1/4-20 x 3/4" screws at the panel block locations (see Photo 20) and the 16 1/4-20 x 1" screws in the center of the two brace sub assemblies (see Photo 19). All of the screws should be very securely tightened by hand.
- Page 11 Each of these feet sits in the pocket of a bracket screwed to the MXR panel. There are two brackets on the first panel and two brackets on the second panel (four total) for each isolation base. The MXR is designed so that one isolation base sits at the very top location (see Photo 26) and one isolation base sits at the very bottom of the frame (see Photo 25).
- Page 12 Note: If your MXR has more than two panels, stand the MXR frame up after the first two panels are complete. Attach the feet on each of the remaining panels and install them one at a time as shown above until all the panels are in place.
- Page 13 Make sure you read and follow all of the instructions in the isolation base manual prior to installing into the MXR Audio Stand frame. You will want to verify that the frame size matches the isolation base size.
- Page 14 MXR Cable Organizer Accessory – The cable organizer system is available for the MXR as an accessory. It bolts into the back of the MXR frame using the remaining threaded holes in the MXR panel that are used to support the isolation bases.
- Page 15 If necessary loosen the top brace that connects the panels in the MXR frame prior to installation of the solid brace inserts and re tighten after assembly. Once the solid brace inserts are in place you can load the oversized...
-
Page 16: Care And Maintenance
Submerging, spraying, or soaking the rack system or isolation base will cause permanent damage to the assembly. Clean the metallic parts of the isolation base and MXR Audio Stand using a lint- free soft (non-abrasive) cloth. Use a damp cloth with a mild soap or Pledge Surface Cleaner if required. -
Page 17: Limited Warranty
Limited Warranty Harmonic Resolution Systems warrants the product designated herein to be free of manufacturing defects in material and workmanship subject to the conditions herein set forth, for a period of 90 days from the date of purchase by the original purchaser. - Page 18 During the warranty period, Harmonic Resolution Systems will repair or replace any defective components free of charge. A Return Authorization Number (RA Number) obtained directly from Harmonic Resolution Systems is required before any product is returned to Harmonic Resolution Systems for any reason. This number must be visible on the exterior of the shipping container(s) for Harmonic Resolution Systems to accept the return.
- Page 19 (MADE IN USA) All Harmonic Resolution Systems Inc. products are 100% Made In The United States of America by skilled craftsmen using only the finest materials and our personal dedication to the highest workmanship standards. ARMONIC ESOLUTION YSTEMS 2495 Main Street, Suite 227 Buffalo, NY 14214 Telephone: 716-873-1437 Web:...
Need help?
Do you have a question about the MXR and is the answer not in the manual?
Questions and answers