Summary of Contents for innovita Primo 11
- Page 1 Primo 6 Primo 11 Instantaneous gas water heater Installation, operation and maintenance manual...
- Page 2 Indoor sound power level Model Water heating energy efficiency class Annual energy consumption PRODUCT DATASHEET Innovita Primo 6 Primo 11 Declared load profile Indoor sound power level dB(A) Water heating energy efficiency class Water heating energy efficiency class Annual energy consumption...
-
Page 3: Table Of Contents
WARNING This booklet contains information relevant to the user as well as the installer. The user must read the following chapters: General safety, Flue gas device and Operation. Gas Safety (Installation and Use) Regulations 1998 In the interest of safety, it is the law that all gas appliances are installed and serviced by a competent person in accordance with the above regulations, building regulations, codes of practice and byelaws of the local water authority. -
Page 4: General Safety Warnings
GENERAL SAFETY WARNINGS The Operation Manual is an integral part of the product and so must When using the device the following safety rules must be applied: be carefully preserved in order to accompany the product; if it is lost or damaged another copy can be requested from Morco Products Do not use the machine for purposes other than those inten- Limited on 01482 325 456 or visit our website www.morcoproducts. - Page 5 fig. 2 Flue gas release safety device Release hood Heat exchanger Ignition electrode Burner Hydraulic valve Temperature regulator Gas valve Gas input Gas adjustment screws Piezoelectric button Gas control Devices pressure Ignition electrode Thermocouple...
-
Page 6: Technical Characteristics
1. TECHNICAL CHARACTERISTICS 1.a Technical Data Primo kW - kcal/h kW - kcal/h Nominal power usage (Pn) 10,1 - 8.686 19,0 - 16.340 Nominal Thermal range (Qn) 12 - 10.320 21,8 - 18.748 Minimal power usage (Pm) 4,9 - 4.214 7,5 - 6.424 Minimal Thermal range (Qm) 6 - 5.160... -
Page 7: Installation
2.b Wall mounting bustible materials, provide a metal sleeve of 115 mm dia for a Primo 6 and 135mm dia for a Primo 11 which allows an air gap of 25 mm. Warning Flue pipes and terminals should comply with BS 715. Terminals Do not install this device in an area that contains dust, greasy va- shall not be sited within 300 mm. -
Page 8: E Water Connection
- The diameter of the flue terminal must match that of the water heater may become dangerous. heater (90mm for the Primo 6 litre or 110mm for the Primo 11 litre) - The overall flue length from the top of the water heater to the top of the external flue must be at least 600mm. -
Page 9: Operation
3. OPERATION A = Gas control on/off ● off position activation position minimum gas level maximum gas level B = Water temperature selector fig. 6 3.a. Function When the water heater is not used for long periods close the gas supply tap or the LPG gas valve on the tank. -
Page 10: B Troubleshooting: Problems And Solutions
4.b Troubleshooting: problems and solutions For the best functioning of the water heater, to prolong its lifetime - Clean the combustion chamber and ensure that it is always safe, ensure that it is inspected at least - Check the ignition, switching off and general functionality of the once a year by a gas safe engineer. - Page 11 FOR THE ENGINEER STARTING UP THE APPLIANCE AND FINAL CHECKS • CLEANING THE MAIN BURNER Start the appliance by following the directions given in section 3b, “Usage”, checking that the appliance is working correctly. Pay spe- To carry out the annual cleaning of the burner, proceed as follows: cial attention to the colour of the flames ensuring there is no yellow- –...
-
Page 12: Warranty
- Insect or debris in the burner or heat exchanger - Blocked gas or water filters - Incorrect operation caused by damaged mixer taps or shower TMV2 Supplied by Innovita Italy Distributed in U.K. by: MORCO PRODUCTS LTD Morco House...
Need help?
Do you have a question about the Primo 11 and is the answer not in the manual?
Questions and answers
Does this model(innovita prima 11) come with a bracket to attach to a wall or do you need to provide your own bracket