Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for annke SANNCE N43SU
Summary of Contents for annke SANNCE N43SU
- Page 1 Quick Start Guide...
-
Page 2: Regulatory Information
Production Information Thank you for purchasing our NVR! This manual is designed for the installation and operation of this product. You can get more information about the features and functions of this product in details. Please read this manual carefully before using. Please contact us if you have any questions. Legal Disclaimer REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. -
Page 3: Safety Instruction
FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and -if applicable -the supplied accessories too are marked with "CE"... - Page 4 Warnings ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
-
Page 5: Table Of Contents
Content Chapter 1 Description of Panels............................ 1 1.1 Front Panel...............................1 1.2 Rear Panel................................1 Chapter 2 Installation and Connections........................2 2.1 NVR Installation..............................2 2.2 Hard Disk Installation............................. 3 Chapter 3 Menu Operation............................4 3.1 Menu Structure..............................4 3.2 System Login..............................5 3.3 Using the Setup Wizard...........................5 3.3.1 Guide.............................. -
Page 6: Chapter 1 Description Of Panels
Chapter 1 Description of Panels 1.1 Front Panel Detailed information for the front panel button: Icon Function The indicator is on when power on To receive remote commands To shift down To shift up To cancel or return to the previous step ENTER To ensure or enter into the next step Notes: This is for reference only, some components may not be included. -
Page 7: Chapter 2 Installation And Connections
Detailed information for the rear panel: Name Name Name Camera input VGA output HDMI port USB port RJ45 port RS-485 input port Power socket GND port Notes: This is for reference only, some components may not be included. This description applies to several models and the connection methods are similar in spite of the different appearance. -
Page 8: Hard Disk Installation
2. Ensure there is ample room for audio and video cables. 3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter. 4. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices. 5. -
Page 9: Chapter 3 Menu Operation
► Connect the data wire and the power wire to the corresponding port of the hard disk Notes: Please turn off the power before you install the hard drive. You can skip this step if you has installed the hard drive on your DVR in advance. Chapter 3 Menu Operation 3.1 Menu Structure [Main Menu]: Open the Main Menu. -
Page 10: System Login
3.2 System Login 1. Login: Log in to the system by inputting your user name and password (Default user name is “admin” and the default password “null” means you needn’t input the password, just keep the password box blank, you can click “OK”... -
Page 11: Time-Language Configuration
3.3.2 Time—Language Configuration You can enter “Guide”, and click “Next” to go to this interface. [Time Zone]: Set and select the time zone. [System Time]: Set the system data and time. [Date Format]: Choose the data format: YMD, MDY, DMY. [Date Separator]: Choose list separator of the data format. -
Page 12: Install Mobile App And Add Device
You can enter “Guide” , and click “Next” to the next step, and then click “Next” again go to this interface. When you connect the NVR to router by using an Ethernet Cable, if there is “Test Gateway..ERR” shows up, click “Retry”... -
Page 13: Add Ip Cameras
recording. Go to NVR’s “Main Menu”>“Net Service”>“Cloud”, make sure your NVR has a high-speed network connection, the “Cloud” will be “Connected” , and click “OK” to save your setting, as shown in the figure below. Go to NVR’s “Main Menu”> “Info”> “Version”> “Serial No” to check your “Serial No”. It’s a combination of 16 characters and numbers, as shown in the figure below. - Page 14 Steps: 1. Connect NVR and IP camera into the same router respectively by using the network cable, make sure they are in the same LAN (It connects to the router through wifi if it is a wifi IP camera, not through the Ethernet cable). 2.
- Page 15 settings, as shown in the figure below. Method 3: 1. Go to NVR’s “Main Menu”> “System”> “Digital”> “Channel Type” to the interface of adding IP camera, for example, you can tick the sixth option, it will connect to 4 NVR and 4 IP cameras. System will reboot after you change the NVR to IP mode, as shown in the figure below.
-
Page 16: Recording Setting
4. Check connection status. Click “Exit”. Live video appears. If you find status is connected but there is still no image, please go to NVR’s “Main Menu”> “System”> “General” to change video standard or reboot NVR to have a try. 3.6 Recording Setting Steps: 1. -
Page 17: Playback
[Redundancy]: Click and check this option to double backup the file. Every video file will be duplicated to saved in two hard disks drive instead of one if your system supports installing two hard drives. Make sure that there are two hard disks installed. One is read-write disk and the other is redundant disk. [Length]: Set the time length of each video file. -
Page 18: Backup
3. Select the time bar shows green to playback (Green represents regular recording). 4. You can click “ ” button to playback the video files. 3.8 Backup Go to NVR’s “Main Menu”>“Record”>“Backup”, you can backup the video files to external storage. Plug the USB drive into the USB 2.0 port, as shown in the figure below. -
Page 19: Alarm Setting
[Type]: Select the corresponding type (“All”, “Alarm”, “MD”, “Alarm/MD”, “Manual”, “General” ) to backup. [Channel]: Select the corresponding channel to backup. [Start Time]: Select time to start backup. [Start Time]: Select time to end backup. Click “OK” when you get the message of “Backup finished”, then you can plug the USB drive out. You need to install the APP “Displayer”... -
Page 20: Video Blind
When system detects the motion signal that reaches the set sensitivity, the motion detect alarm is on and the linkage function will be turned on. 3.9.2 Video Blind Steps: 1. Go to NVR’s “Main Menu”>“Record”>“Record Configuration” to tick “Alarm”. 2. Go to NVR’s “Main Menu”>“Alarm”>“Video Blind”go to the interface of Video Blind. Click and check “Enable”, select “Channel”, “Sensitivity”, “Period”, “Alarm Out”, “Record Channel”, “Buzzer”, “Send Email”... -
Page 21: Abnormality
“Enable”, select “Channel”, “Sensitivity”, “Period”, “Alarm Out”, “Record Channel”, “Buzzer”, “Send Email” according to you needs, and then click “OK” to save, as shown in the figure below. When the equipment can not get the channel video signal, the video loss alarm and the linkage function will be turned on. - Page 22 Menu”> “Info”> “Version” to confirm that the “Nat status” shows connected. 2. Please go to NVR’s “Main Menu”> “Alarm”> “Motion Detect” to tick “Enable” and “Send Email” function, as shown in the figure below. 3. Please go to NVR’s “Main Menu”> “System”> “Net Service”> “EMAIL” to go to the interface of Email Setting, double-click “EMAIL”, as shown in the figure below.
-
Page 23: Chapter 4 Remote Control
Notes: The account of User Name is the same as Sender, while Receiver is a different account to receive email alerts. Click “OK” to save after “Mail Testing” succeeds. It will send alarm message. Please check the camera after you got the alarm message and check the recorded video later. Chapter 4 Remote Control 4.1 Accessing by Web Browser Before start:... - Page 24 Notes: The default user name is “admin”, and can not be changed. The password is the same to the password of NVR (The default password “null” means you needn't input the password, just keep the password box blank), then you can login on Web Browser. You will go the interface as shown in the figure below after you login successfully. You will get the image if the camera connects to the channel successfully.
- Page 25 install “Active.exe” when you visit for the first time. Login By User or By Device By User: Click “Register” and follow the instruction when you get a new account to login, as shown in the figure below. You can login directly if you have registered an account on your mobile phone. By Device: [Serial NO.]: Input your NVR ID, enter “Main Menu”...
-
Page 26: Cms
4.2 CMS CMS client software is in the supplied CD. It shows like that after installation. Double-click the icon of CMS and login, you will go to the interface as shown in the figure below. Click “System”>“Device Manager”>“ADD AREA” >“ADD DEVICE” , you will go to the interface as shown in the figure above. -
Page 27: Accessing By Mobile Phone
4.3 Accessing by Mobile Phone 4.3.1 iPhone / iPad a Install the XMEye app for free from the APP Store. Tap the icon XMEye to open the APP. b Tap Register to create a new account (Need to input the User name and Password). c Tap “+”... -
Page 28: Android
manually if you can not scan the QR code. 3 [User Name]: admin 4 [Password]: The password is the same to the password of NVR(The default password “null” means you needn't input the password, just keep the password box blank). e. -
Page 29: Chapter 5 Faq & Troubleshooting
3 [User Name]: admin 4 [Password]: The password is the same to the password of NVR(The default password “null” means you needn't input the password, just keep the password box blank). e Tap OK to add your device to the APP. f Whenever you open the XMEye APP, the Device List window will be popped up for the first time. - Page 30 Solutions: Step 1: You can right click the mouse to get a desktop shortcut menu in the preview mode. Click “Guide” and select “Auto connected mode”, then click “Next” and “OK” to save the settings. Step 2: Click the icon “connect all video” at the bottom of screen. Step 3: Use your hands to cover the front of camera.
- Page 31 the camera, cable, or channel port is damaged or not. For example: 1. Connect the camera C1 to the channel A1 with the cable B2 to confirm if it is the cable B1's problem 2. Connect the camera C1 to the channel A2 with the cable B2 to confirm if it is the camera C1's problem. 3.
- Page 32 Possible Reasons: Connection cable is damaged. Input mode of the monitor is incorrect. Solutions: Method 1: Please go to Guide and select Auto-connected mode. Method 2: Please make sure your camera has been connected correctly. 10. Forget password Solutions: Method 1: Please make sure that there is no default password, you can login directly. Method 2: Please send the date and model of your NVR, you can email to us or make a phone call to us.
Need help?
Do you have a question about the SANNCE N43SU and is the answer not in the manual?
Questions and answers