Denon av surround receiver operating instructions avr-2307ci (82 pages)
Summary of Contents for Denon AVR-2312
Page 1
SERVICE MANUAL MODEL E1C E1K AVR-2312CI AVR-2312 INTEGRATED NETWORK AV RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
PRESET CHANNEL 2 Service Jig d When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from Denon Official Service Distributor in your region if necessary. 8U-110084S EXTENSION UNIT KIT 1 Set...
DISASSEMBLY • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". •...
Page 8
About the photos used for "descriptions of the DISASSEMBLY" section • The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as "Shooting direction: ***". • Refer to the diagram below about the shooting direction of each photograph. •...
1. FRONT PANEL ASSY Proceeding : CABINET TOP FRONT PANEL ASSY → Remove the screws. View from the bottom Cut the wire clamp band, then disconnect the connector wires and FFC cables. Remove the screws. STYLE PIN : Loosen CN602 TAPE : Remove FFC cable CN390...
2. HEAT SINK ASSY Proceeding : CABINET TOP HEAT SINK ASSY → Remove the screws. View from the bottom Cut the wire clamp band, then remove the screws. Disconnect the connector wires. Shooting direction: D Shooting direction: C CN602...
Page 11
Cut the wire clamp band, then disconnect the connector wire and FFC cables . STYLE PIN : Loosen HEAT SINK Assy TAPE : Remove FFC cable CN390 FFC cable Cut the wire clamp bands, then disconnect the connector wires. CN461 CN701 CN703 CN702...
3. HDMI UNIT ASSY HDMI UNIT ASSY Proceeding : CABINET TOP → Remove the screws, then remove the BACK PANEL and the HDMI BRACKET. Shooting of photograph: A Cut the wire clamp band, then disconnect the connector wires and the FFC cables. Remove the PCB DOCK from the PCB SIDE CNT and PCB RS232C(Board to board).
Page 13
Disconnect the connector wire. Remove the screws. CN931 Remove the screws.
Page 14
Cut the wire clamp band, then disconnect the connector wires. CN941 CN932 CN940 CN903 CN781 Cut the wire clamp band, then disconnect the connector wires. CN461 CN701 CN703 CN702...
Cut the wire clamp bands, then disconnect the connector wires, and remove the screws. CN203 CN902 Remove the screw. Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HDMI UNIT ASSY. 4. TRANS MAIN Proceeding : CABINET TOP HDMI UNIT ASSY POWER TRANS...
STATUS paths. (Troubleshooting) CHANNEL 1 The signal paths of the set can be easily confirmed after repair. When using multiple DENON AV receivers in the same room, make PRESET Remote ID Setup mode STATUS this setting so that only the desired AV receiver operates.(Refer to 22...
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When the set is started up in this mode, the version information is displayed. Starting up: Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "iPod 1 " buttons. Now, press the "STATUS"...
Page 18
i Ethernet(DM860) 1st Boot Loader, Hardware ID : E t h e r n e t F B L Upper Lower * * * * * * - A A o Ethernet(DM860) 2nd Boot Loader, Rhapsody Flag : E t h e r n e t S B L Upper Lower...
Page 19
1.3. Error display See the following table for each "Error information" display and its explanation (status). Display order is q , w , e , r , t , y , u , i . Condition Status FL Display Trouble shooting •...
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifications Error mode (Displaying the protection history): When the set is started up in this mode, the error information is displayed. Starting up: • Common in all the models Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "SLEEP" buttons. The error (protection history display) mode is set.
Page 21
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. Start up the set in error (protection display) mode and display the error, then press and hold down the "INTERNET RADIO" button for 3 seconds. P R O T E C T H I S T O R Y Upper...
3. Remote ID Setup mode 3.1. Specifications When using multiple DENON AV receivers in the same room, make this setting so that only the desired AV receiver operates. 2.2. Setting the AV receivers Starting up: Press and hold both "STATUS" and "PRESET 1" buttons for over 3 second with the power turned on.
4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) d This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 4.1. Starting diagnostic mode Press the "PRESET CHANNEL 1" and "STATUS" button while simultaneously pressing those two buttons of this unit. Q1, Q2 and Q3 are lit in FL display.
Page 25
Output sequence of remote control codes Confirmation item Details of how to operate remote controller *a) Contents of confirmation Setting and display Remarks ※ It is useful to form a macro program. *b) OSD FUNCTION Video Convert(IP Scaler) : ON, All Sources qZONE2 POWER OFF 1.Press [AMP] ·OSD Display / Output : HDMI...
Page 26
3.5. Audio system confirmation items fig.XX : Refer to the block diagram of the fig.XXth. Output sequence of remote control codes Confirmation item Contents of confirmation Setting and display Details of how to operate remote controller Remarks ※ It is useful to form a macro program. Input Mode : Fixed ANALOG qZONE2 POWER OFF ·Input : Analog / Output : Speakers (Front L/R)
Page 27
Output sequence of remote control codes Confirmation item Contents of confirmation Setting and display Details of how to operate remote controller Remarks ※ It is useful to form a macro program. Amp assign : NORMAL qZONE2 POWER OFF ·Input : Analog / Output : Speakers (Front L/R) A/D (signal) Path 1.Press [AMP] 2.Press [ZONE SELECT] , Select "ZONE2"...
Page 28
Output sequence of remote control codes Confirmation item Contents of confirmation Setting and display Details of how to operate remote controller Remarks ※ It is useful to form a macro program. qZONE2 POWER OFF ·Input : Analog / Output : Speakers (SURR BACK L/R) Amp Assign (signal) Path Amp assign : 2CH 1.Press [AMP]...
Page 30
fig.3 AVR3312/2312 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 : AVR3312 AD8195 Port A ADV8002-4 : AVR2312 Buffer HDMI FRONT IN Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC HD_VSYNC ADV3002 VIDEO Port C HD_DE HDMI OUT1 HD/CS HD_SFL PROCESSING VS/FIELD...
Page 32
fig.4 (2/2) AVR3312/2312 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 : AVR3312 AD8195 Port A ADV8002-4 : AVR2312 Buffer HDMI FRONT IN Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC HD_VSYNC ADV3002 VIDEO Port C HD_DE HDMI OUT1 HD/CS HD_SFL PROCESSING VS/FIELD...
Page 33
fig.5 (1/2) AVR3312/2312 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 : AVR3312 AD8195 Port A ADV8002-4 : AVR2312 Buffer HDMI FRONT IN Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC HD_VSYNC ADV3002 VIDEO Port C HD_DE HDMI OUT1 HD/CS HD_SFL PROCESSING VS/FIELD...
Page 34
fig.6 AVR3312/2312 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 : AVR3312 AD8195 Port A ADV8002-4 : AVR2312 Buffer HDMI FRONT IN Port B u-COM HD_PCLK IC111 HDMI IN1 HD_HSYNC HD_VSYNC ADV3002 VIDEO Port C HD_DE HDMI OUT1 HD/CS HD_SFL PROCESSING...
Page 35
fig.8 (1/2) AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL AMP/PRE EXTFR ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR EXTSL ADINL/R DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L EXTBSL FRONT HEIGHT AMP/PRE EXTBSR EXTC...
Page 38
fig.10 AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL EXTFR AMP/PRE ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR ADINL/R EXTSL DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L EXTBSL FRONT HEIGHT AMP/PRE EXTBSR EXTC...
Page 39
fig.11 (1/2) AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL AMP/PRE EXTFR ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW V.AUX AMPFR AMP/PRE ANAFR ADINL/R EXTSL DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L FRONT HEIGHT EXTBSL AMP/PRE EXTBSR EXTC...
Page 49
fig.16 AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL AMP/PRE EXTFR ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR EXTSL ADINL/R DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L EXTBSL FRONT HEIGHT AMP/PRE EXTBSR EXTC...
Page 50
fig.17 AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL AMP/PRE EXTFR ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR ADINL/R EXTSL DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L EXTBSL FRONT HEIGHT AMP/PRE EXTBSR EXTC...
Page 51
fig.18 AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL AMP/PRE EXTFR ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR EXTSL ADINL/R DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L EXTBSL FRONT HEIGHT AMP/PRE EXTBSR EXTC...
Page 52
fig.19, 20 AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL AMP/PRE EXTFR ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR EXTSL ADINL/R DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L EXTBSL FRONT HEIGHT AMP/PRE EXTBSR EXTC...
Page 53
fig.22 (1/2) AVR3312/2312 ANALOG AUDIO BLOCK H/P OUT EXTFL AMP/PRE EXTFR ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR EXTSL ADINL/R DAFR DAZONE2 TONE EXTFR NOT USED EXTSR DAZONE3 AVR3312 ONLY : FH_L EXTBSL FRONT HEIGHT AMP/PRE EXTBSR EXTC...
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from DENON Official Service. Distributor in your region if necessary. NOTE: The incorrect connection with in the JIG (EXTENSION UNIT KIT) may cause damage.
Page 60
(2) Disconnect the connector board. Board to board Board to board PCB HDMI Board to board Board to board CN931 PCB VIDEO Board to board PCB INPUT Board to board...
Page 61
(3) Detach PCB HDMI from the chassis, and turn it over. Please put an insulation sheet that is larger than PCB HDMI under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. VIDEO PCB HDMI PCB AUDIO PCB...
Page 62
PCB FRONT CNT Insulation sheet PCB SIDE CNT PCB INPUT Connection table of Board to Board Ref. No. Ref. No. 11 pin CN28A SIDE CNT CN28B HDMI 21 pin CN27A SIDE CNT CN27B HDMI FRONT CNT 27 pin CN24A CN24B HDMI FRONT CNT 15 pin...
WHEN THE MICROPROCESSOR IS REPLACED WITH A NEW ONE When the U-PRO (Microprocessor) or the Flash ROM is replaced, confirm the following. After PWB Name Ref. No. Description Remark replaced R5F5630ECDFB SOFTWARE: Main HDMI IC201 R5F3650KNFB SOFTWARE: Sub HDMI IC231 MX29LV160DBTI-70G SOFTWARE: DSP ROM HDMI...
Page 64
Once updating starts, normal operations on the AVR-2312 cannot be performed until updating is completed. Also, setting items of the GUI menu of AVR-2312 or setting items of the image adjustment may be initialized. Note down the settings before updating, and set them again after updating.
Page 65
Error Details of Error code Display Coping strategies Code Check the network connection. C o n n e c t i o n f a i l Connection to DPMS failed. Carry out the update in an environment (can not get NTP) that has little network load.
Page 66
Error Details of Error code Display Coping strategies Code Line, etc., is busy when logging into DPMS when firmware such as Sub S e r v e r b u s y Carry out the update in an environment CPU, DSP, FPGA, and PLD was that has little network load.
Page 67
Error Details of Error code Display Coping strategies Code NACK was received when "C" S u b * * * m i n Turn off and on the power. Updating command sent to Sub CPU, DSP starts automatically. C o n n e c t i o n F a i l 5 A PLD etc.
Page 68
Error Details of Error code Display Coping strategies Code Acquisition of (Application Mode) Check the network connection. E t h e r I M G * * * m i n IP address failed before rewriting Carry out the update in an environment C o n n e c t i o n F a i l A 0 DM860 was rewritten (AutoIP).
Page 69
Device display during firmware update Target of device when firmware updated. Target of device Display Error cpde 08~0C M a i n * * * m i n 10~15 Main 22~24 U p d a t i n g * * % 36~3E 50~52 S u b * * * m i n 54~58...
ADJUSTMENT Audio Section Adjusting Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, When the power turned on, does the ON/STANDBY does the ON/STANDBY indicator on the front panel indicator on the front panel flashing green? flashing red? Is the fuse blown? Refer to 1.2.Fuse is blown.
2. Analog video Perform the operation below beforehand. b Check that the connection cable and the Monitor are normal. b Set VIDEO CONVERT ON. b Set COMPONENT signal to 480i. b Set Function to the following. V : SAT S : DVR COMPONENT : SAT MONITOR OUT (CVBS/Cmponent) output NG Input...
Page 77
Input CVBS,S,COMPONENT REGULATOR B'D flaw. Is the power supply voltage correctly output? VIDEO B'D and REGULATOR V+5V : CN931-4pin B'D and connection of the wire V-5V : CN931-1pin are defective. Check on set value of each IC. Is they the following voltage values? HDMI B'D flaw.
Page 78
VIDEO B'D flaw. Extend HDMI B'D using a jig. Is the signal output from IC551(AVDM-2000)? : J5195 The parts between IC551 and COMPONENT(Y) : J5241 JK551 or JK557 are defective. COMPONENT(Cb) : J5133 COMPONENT(Cr) : J5235 Is the signal output from IC551(AVDM-2000)? JK554 Lead The soldering (IC551) is defective.
Page 79
I2C communication wave form CH1: CLK CH1: DATA...
Page 80
HDMI test point (COMPONENT SIDE) Detail A S_DET COMP_DET En_CVBS En_Y VSDA VSDA V_DET En_Pr En_Pb Detail B S(C) S(Y) COMPONENT(Cr) COMPONENT(Cb) COMPONENT(Y)
Page 81
VIDEO test point JK 554 1.DIN_SA T_Y 2.V G N D 3.DIN_SA T_CB C 5106 C 5108 C 5102 C 5104 4.V G N D 5.DIN_SA T_CR 1.M O N_CO M P _Y_O UT 6.V G N D 2.V G N D 7.SA T_LIN E1 3.M O N_CO M P _CB_O UT 8.SA T_LIN E2...
(6) Is the BD/DVD player's HDMI output setting correct? the BD/DVD player's operating instructions. (7) When you use a DENON BD/DVD player's, is the fluorescent display tube's "HDMI" indicator lit? If you use a non-DENON BD/ DVD player's, proceed to "YES".
Page 83
Check TV Use an HDCP-compatible TV. PC TVs (11) Is the TV HDCP-compatible? cannot be used. If the TV is not compatible with resolutions of 1080P, no picture will be output, even (12) Is the TV compatible with resolutions of 1080P? if the BD/DVD player's resolution is set to 1080P.
Page 84
/JK113/JK114/JK121/ display's "HDMI" indicator lit? voltage of the HDMI connector for the input on the JK122) to the IC If using a non-DENON BD/ side on which the BD/DVD player is connected. (IC101/111/121) is DVD player, proceed to "NO". Is communication waveform confirmed in defective.
Page 85
Check operation of IC121(ADV7844). (25) Check power supply. Are 1.8V supplied to L1202/L1203/L1204/L1205? The power supply circuitry is defective. Are 3.3V supplied to L1201/L1206/L1207? (26) Check xtal oscillator. The X1201 or IC121 is defective. Is oscillation of X1201(28.6363MHz) transmitted? (27) Check RESET. Is RESET waveform confirmed in TP[7844_RESET], when power The RESET circuitry or IC121 is defective.
Page 86
3.2. HDMI test point and waveforms (COMPONENT SIDE) Detail A TX1_D1- TX1_CK- TX1_D1+ TX1_CK+ TX1_D2+ TX1_D2- TX1_D0- TX1_D0+ DDC_DATA DDC_CLKHPD Detail B DDC_CLK HPD DDC_DATA...
Page 88
DDC_CLK/DDC_DATA/TMDS : Check items (17)/(19)/(24)/(32) 0.9V DDC_CLK 2.48V TMDS Waveform DDC_DATA Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items (22) CEC3.3V 338ms 3002_RESET Controlled waveform(I2C), when power is turned on : Check items (23) HDMI_SCL HDMI_SDA POWER ON...
Page 89
Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items (27) CEC3.3V 338ms 7844_RESET Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items (31) DV3.3V 314ms 8002_RESET DV3.3V 10ms 10ms...
4. AUDIO 4.1. AUDIO CHECK Refer to "Audio Check PATH" (99 page). Audio output NG. CHECK1 INPUT SURROND MODE SOURCE Check ANALOG audio BLOCK. Audio output OK? ANALOG 2CH ANALOG DIRECT CHECK2 INPUT SURROND MODE SOURCE Check Digital audio BLOCK. Legacy Audio output OK? COAX or OPT...
Page 92
4.2. Power AMP (MAIN UNIT) No sound is output. The protector operates. Is the power transistor open or short- circuited? Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
Page 93
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. SIDE CNT B'D CN41A 4-7pin? Is the audio signal transmitted to The power amplifier is repaired. INPUT B'D CN461? Connect the connectors properly.
5. Network/USB 5.1. Cannot connect to network Checking the environment Check the LAN cable properly then turn the Is the LAN cable properly connected? power back on. Checking the settings Set the IP address and other parameters properly. For a fixed IP setting, check Are the AV RECEIVER's network settings correct? whether the IP address is redundant with that of other devices, and check whether the...
Page 95
5.2. USB device is not recognized Checking the USB device Are you using a USB hub? Don't use the USB hub. Only mass storage devices in FAT16 or FAT32 formats or MTPcompatible devices Is the USB device compatible with the set? and iPod (Remove some models) are supported.
Page 96
HDMI test point CN321 Q3200 IC323 IC406 IC322 IC390 IC304 IC301 CN903 (COMPONENT SIDE) USB test point JK608 BN 608 JK 608 C 6811 CU P 12384-4 1. V B U S BN608 2. U S B D + 3. U S B D - 4.
6. SMPS DC 5V is not output. Is there damage in IC901 Replace the IC901(TOP258MG) and (TOP258MG)? D9001/D9002/D9003/D9004. Is there the damage in D9001/D9002/ Is the fuse (F9001) blown? Replace the parts of damage. D9003/D9004/C9004? Is there solder short circuit in the PWB The solder short part of the PWB board board? is repaired.
Page 98
Operation waveform for each part After primary side rectification (Caution: High voltage, electric shock) Primary drain (Caution: High voltage, electric shock) C9002 0.01uF 250V 1N4007 D9001 D9002 1N4007 1N4007 After secondary rectifications D9003 LF902 1N4007 D9004 LF-4ZB-E273H D9005 1N4007 1N4007 D9006 R9002 R9003...
Page 99
Audio Check PATH Refer to troubleshooting "4.1. AUDIO CHECK"(91 page). HDMI CHECK6 TRANSMI TTER ADV8002 CHECK5 wi t h s cal er vi deo encoder et c. . . ADV7844 FRONT TMDS BUFFER AD8195 CHECK4 EPM240T100CN5 CHECK2 SPDI F/I 2S SELECTOR SPDI F LC89058W -E DI GI TAL AUDI O...
LAEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15220FP ANALOG H/POUT SPEAKER LINE IN + GAIN ADJ. + MIC IN + AK5358B + + AK4358VQ - - AZ4580 MAX.OUTPUT 7.78Vrms +30dB SP OUT R2A15220FP MAX.OUTPUT 3.8Vrms AK4358VQ 4.24Vrms/8Ω DIFF.OUT AK5358B 0dBFS=5Vpp =1.77Vrms FULL SCALE LEVEL=2Vrms +20dB SINGLE INPUT...
Page 106
R2A15220FP LEVEL DIAGRAM SB-ch FRONT/ZONE ASIGN 0dB ZONE2/3 from F-ch from SPEAKER DA SB-ch + LINE IN + MAIN from EXT.IN SB-ch AVR2312/3312, ZONE2 NJW1194 ONLY TONE MONO MUTE PREOUT MONO AVR3312 ONLY ZONE3 NJW1194 TONE MONO MUTE PREOUT MONO +30dB SP OUT 4.48Vrms/8Ω...
SPMS (COMPONENT SIDE) 2.2 X 1.2 C M D 1A 629 2.2 X 1.2 BK 903 5600uF/ 6. 3V 5600uF/ 6. 3V I C 903 1.2 X 3.1 C 9023 C 9021 D 9012 R 9019 SMPS B'D ADJ 1 ADJ 2 R 9018 R Y 901...
SPK_PREOUT (COMPONENT SIDE) JW 703B (33/23/6006) B K 701 C 7872 C 7813 JK 683 JK 682 JK 681 JK 684 JW 701A ( S R 6006) C 7871 C 7873 C 6805 C 7853 C 7863 C 7843 JK 781 JK 782 C 7833 C 7803...
SPK_PREOUT (FOIL SIDE) C 6877 C 7825 C 6745 C 6782 C 6820 C 7826 C 7815 C 7845 C 7835 C 7865 C 7878 C 7875 C 7805 C 7827 C 7855 C 7836 C 7866 C 7876 C 7816 C 7806 C 7846 C 7856...
INPUT (COMPONENT SIDE) 7.1CH IN IPOD SAT /CBL SL/SR C/SUB PH ON O AU X2 SBL / S BR JK 464 JK 462 JK 461 JK 465 C4647 C4648 C4643 C4644 C4637 C4638 C4633 C4634 C4627 C4628 JK 463 C4623 C4624 C4617 C4618...
INPUT (FOIL SIDE) R4692 R4609 R4620 R4630 R4691 R4640 C4649 R4610 R4619 R4629 R4639 R4649 C4609 C4619 C4629 C4639 R4650 C N 45B R4665 R4666 RE C_ L R4757 R4751 1. R E C _L 2. A G N D C4666 3.
FUSE (COMPONENT SIDE) FUSE (FOIL SIDE) POSISTOR (COMPONENT SIDE) POSISTOR (FOIL SIDE) C UP 12388-2 Z : T3.15A L/ 250V C N 932 F9302 R 9312 R 9316 : T3.15A L/ 250V R 9313 F9304 : T3.15A L/ 250V F9303 C N 941 C N 940 R 9315...
FRONT (COMPONENT SIDE) V.AUX (COMPONENT SIDE) CU P 12384-2 FI L1 C 6008 BK603 LU G 62 C N 69A FI L2 VK K G N D S W M 3.3V J6354 VK K DA +8V C 6032 C 6035 J6732 V S E LA C N 601...
HDMI FFC (COMPONENT SIDE) HDMI FFC (FOIL SIDE) USB (COMPONENT SIDE) USB (FOIL SIDE) L6001 C 6802 C 6801 BN 608 JK 608 D 6836 D 6835 C 6811 CU P 12384-4 C 6836 C 6835 BK612 R 6842 R 6838 1.
SELECTOR (COMPONENT SIDE) SELECTOR (FOIL SIDE) BN 604 C 6021 BN 601 C 6027 D 6021 C N 602 C 6001 C 6001 FI L1 FI L1 FI L1 LU G 64 Q 6313 Q 6313 C 6425 C 6425 FI L2 FI L2 FI L2...
SIDE_CNT (COMPONENT SIDE) SIDE_CNT (FOIL SIDE) C N98B C N 97B C N28A C N 27A C 9617 C 9618 R9608 C 9610 C 9611 C 9616 C 9612 C 9609 R9607 R9646 C 9645 C 9615 C 9605 R9645 C N 961 C 9601 C 9644...
VIDEO (COMPONENT SIDE) JK 554 1.DIN_SA T_Y 2.V G N D 3.DIN_SA T_CB C 5106 C 5108 C 5102 C 5104 4.V G N D 5.DIN_SA T_CR 1.M O N_CO M P _Y_O UT 6.V G N D 2.V G N D 7.SA T_LIN E1 3.M O N_CO M P _CB_O UT 8.SA T_LIN E2...
FROM DIGITAL CONNECT (PAGE 15/30) LUG61 CN69A CHASSIS FPC 1.0-11S-40PW FIL1 R6003 FIL1 FIL1 FIP & KEY PART SWM3.3V VOLUME ENCODER PART R6004 OPEN FIL2 FIL2 SWM3.3V J6354 FIL2 FIP POWER PART OPEN J6352 R6352 VSELA R6354 C6902 OPEN VSELA VKK GND VKK GND C6903...
OPTION B R6925 AVR3312/2312 MODEL AVR3312 AVR2312 AVR2312 AREA E3/U AVR_E2 AVR_E1C_K OPEN OPTION A OPTION B OPEN OPEN OPEN OPTION C OPEN OPEN OPEN C6923 R6921 L6752 75J-207CX 1.2K CLM4B001Z 4700P(M) C6921 8200P(M) R6927 C6931 R6923 10/50V TU_+9V 100K R6929 A+8V OPEN...
SIDE CNT_CUP12387Z TO M-X PORT TO M-X PORT (PAGE 7/30) (PAGE 7/30) CN98B CN97B C125Z2-11 C125Z2-15 AVR3312 USA VER. ONLY IC961 PQ033DNA1ZPH C9602 R9601 Specific IC 10/50V R9607 C9615 10/50V C9603 R9602 10/50V C9609 TO HD RADIO AUDIO_R AUDIO_M C9610 AUDIO_L C9604 R9603...
TO CONNECT B PART TO CONNECT A PART TO CONNECT B PART (PAEG 9/30) (PAEG 8/30) (PAEG 9/30) CN41B CN42B CN43B C125Z2 C125Z2 C125Z2 Trans. Temp_detect Part C4680 C4682 R4773 100K 0.022u 6800P R4774 100K R4761 R4765 C4676 R4662 R4680 R4682 D2399 R4664...
** IMPORTANT SAFETY NOTICE. SMPS B'D COMPONENT IDENTIFIED BY MARK HAVE SPECIAL CHARACTERISICS. IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY MANUFACTURER'S SPECIFIED PARTS. ** THE UNIT OF RESISTANCE IS OHM. K = 1000 OHM. M = 1000KOHM. ** THE UNIT OF CAPACITANCE IS MICROFARAD(uF) pF = 10 uF ** THIS SCHEMATIC DIAGRAM MAY MODIFIED AT ANY TIME WITH THE...
(PAGE19/30) (PAGE15/30) TO LEVEL CHG. TO DIGITAL CONT. N1B(EUR) Q2010 THER PROT C OPEN R2124 R2125 R2130 TRIGGER 2 OPEN OPEN AVR3312: OPEN R2042 open AVR2312: 4.7k§Ù R2055 open R2040 4.7K R2073 R2041 4.7K open R2109 4.7K Q2011 IPOD R2045 4.7K OPEN R2046...
(PAGE 21/30) (PAGE 21/30) (PAGE 21/30) FROM PLD PART TO PLD PART FROM PLD PART (PAGE 18/30) FROM SCPU PART DSP_CONT TP42 TP41 R4153 OPEN R4152 R4159 DSP_FLAG0 C4161 R4151 IC409 1000P W9864G6JH-6 C4097 R4099 C4106 VDD_INT DAI_P09 FLAG0 DAI_P05 R4098 C4107 DQ15...
(PAGE 21/30) (PAGE 18/30) TO SUB CPU TO AUDIO PLD R4517 open open R4518 DA+5V R4195 DA-8V R4187 R4183 DA+8V OPEN OPEN C4193 R4191 R4189 C4181 D_AUDIO OPEN OPEN OPEN R4185 OPEN ADINL OPEN ADINR R4193 OPEN R4194 DAGND OPEN C4194 R4192 R4188...
EXPLODED VIEW E2,EA,E1C model only WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
PARTS LIST OF EXPLODED VIEW z Parts indicated by "nsp" on this table cannot be supplied. z P.W.B. ASS'Y indicated by "nsp" on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts list and order replacement parts. z Parts indicated by the "...
PACKING VIEW 6-10 PARTS LIST OF PACKING & ACCESSORIES z Parts indicated by "nsp" on this table cannot be supplied. z Parts indicated by the " ★ " mark are not illustrated in the packing view. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 161
Ref. No. Part No. Part Name Remarks Q'ty INSTRUCTION MANUAL ASS'Y MANUAL CD ASS'Y CFT1A041ZA 352010042009D MANUAL, CD ASS'Y E2,EA CFT1A042ZA 352010043002D MANUAL, CD ASS'Y CFT1A043ZA 352010051003D WARRANTY CARD CQE1A224Q CARD, WARRANTY CQE1A473Y S.S LIST CQE1A226P MANUAL GUIDE 542110062003D CQX1A1621Z MANUAL GUIDE E2,EA 542110063006D...
SEMICONDUCTORS Only major semiconductors are shown. General semiconductors etc. are omitted from list. The semiconductors which have a detailed drawing in a schematic diagram are omitted from list. 1. IC's R5F5630ECDFB (DIGITAL : IC201) RX630 Group PLQP0144KA-A (144pin LQFP) (Top) R5F5630ECDFB Terminal Functions Pin Name Synbol Tolerant I/O Pu/Pd...
Page 163
Pin Name Synbol Tolerant I/O Pu/Pd LvCnv STBY stop Function 23 VCC Power supply pin 24 P35(input only)/NMI NC TRST#-A/P34/ ○ E20 Emulator control signal/Usual:"Hi-z" IRQ4-C/SCK6-A/ TRST# SCK0-B P33/TIOCD0-B/ PLDAERR ○ O/L PLD ERROR detection(Output of A PLD) RXD6-A/RXD0-B/ IRQ3-DS P32/TIOCC0/ ○...
Page 164
O/L MAIN-SUB CPU communication control output pin 71 P75/SCK11 O/L MAIN-SUB CPU communication control output pin 72 P74 ACK SIMO PC1/IRQ12-C/ SUB UPDATE mode control (DPMS/DENON WRITTER) ○ SUB UPDATE Usual:L SUB rewrite mode:H(SUB reset) SCK5-C 74 PL1 O/L SUB CPU POWER ON/OFF switch(H:ON) SUB CPU POWER ○...
Page 165
100 P65 PRE SB MUTE PE7/TIOCB11/ PRE F/C/S/SW O/L PRE OUT MUTE control IRQ7-C/AN5 PE6/TIOCA11/ NC(AVR-2312)/ O/L PRE OUT MUTE control IRQ6-C/AN4 PRE Z3 MUTE(AVR-2312) O/L NC 103 PK5/TXD4-B O/L NC 104 P70/SCK4-B O/L NC 105 PK4/RXD4-B PE5/TIOCB10/ O/L NC IRQ5-C/AN3...
Page 166
Pin Name Synbol Tolerant I/O Pu/Pd LvCnv STBY stop Function P41/IRQ9-DS/ MODE Region switch input AN001 140 VREFL0 VREFL0 P40/IRQ8-DS/ THERMAL D PROTECTION detection pin(THERMAL D) AN000 142 VREFH0 VREFH0 Standard power supply input 143 AVCC0 AVCC0 Analog power supply POWER KEY ○...
Page 168
ASPECT_L 20 P80/(RXD5) ASPECT select (JP only) 21 P77/(CLK5) PLD rewriting control (JTAG) SUB TDO A PLD control pin/ DENON WRITTER/ MITSUBISHI rewritten for A PLD CS /"D/M" 22 P76/(TXD5) determining (DW :L) A PLD DATA A PLD control pin...
Page 169
Pu/Pd Pin Name Synbol I/O Type P.OFF Function (Ext.) STBY 61 P30 DAC MS DAC control pin(ASK4358) 62 VSS 63 P27 DAC RST DAC control pin(ASK4358) MODE1=O/H DIGITAL VIDEO power control pin (DV5V,DV3.3V) 64 P26 DV POWER MODE2=O/L 65 P25/INT7 ADV7844 INT1 HDMI RECEIVER(ADV7844)INT output 66 P24/INT6...
Page 173
LC89058W-E (HDMI : IC403,IC404,IC405) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA RLRCK XMODE LC89058W-E DGND DV DD DV DD DGND GPIO0 RBCK GPIO1 RMCK AGND GPIO2 AV DD GPIO3 RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 174
LC89058W-E Continued from preceding page. Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND...
Page 175
ADSP21487KSWZ-4B (HDMI : IC408) PIN 1 Preliminary Technical Data ADSP-21483/21486/21487/21488/21489 TOP VIEW (PINS DOWN) 176-LEAD LQFP_EP LEAD ASSIGNMENT ADSP21487KSWZ Terminal Function Table 53. 176-Lead LQFP_EP Lead Assignment Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. SDDQM DAI_P10 DPI_P08 FLAG0 SDCKE...
Page 177
W9864G6JH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY...
Page 178
W9864G2IH W9864G6JH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 183
DSDL4 DAC4 DSD Lch Data Input Pin DSDR4 DAC4 DSD Rch Data Input Pin DSDL1 DAC1 DSD Lch Data Input Pin DSDR1 DAC1 DSD Rch Data Input Pin DSDL2 DAC2DSD Lch Data Input Pin DSDR2 DAC2 DSD Rch Data Input Pin H27U1G8F2B Series DSDL3 DAC3 DSD Lch Data Input Pin...
Page 184
1.2 PIN DESCRIPTION H27U1G8F2BTR-BC Pin Function Pin Name Description DATA INPUTS/OUTPUTS The IO pins allow to input command, address and data and to output data during read / program IO0 ~ IO7 operations. The inputs are latched on the rising edge of Write Enable (WE). The I/O buffer float to High-Z when the device is deselected or the outputs are disabled.
Page 187
±15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR in a Small Footprint Datasheet LAN8700 Pin Description Table 2.1 LAN8700/LAN8700I 36-PIN QFN Pinout PIN NO. PIN NAME PIN NO. PIN NAME nINT/TX_ER/TXD4 RX_DV RX_CLK/REGOFF CRS/PHYAD4 RX_ER/RXD4 MDIO TXCLK nRST TXD0 TX_EN TXD1...
Page 188
SAA7121 (HDMI : IC323) 33 V SSA2 res. V SSA1 V DDA3 CVBS V SSD1 res. SAA7120 V DDD1 V DDA2 SAA7121 RCV1 res. RCV2 V DDA1 res. MBH790 SAA7121 Block Diagram V DDA1, handbook, full pagewidth RCV1 TTXRQ XTALO V DDA2 , V DDA4 V DDA3 RESET SDA SCL RCV2...
Page 189
Digital Video Encoder (ConDENC) SAA7120; SAA7121 SAA7121 Pin Description PINNING SYMBOL DESCRIPTION − res. reserved test pin; connected to digital ground for normal operation test pin; connected to digital ground for normal operation line-locked clock; this is the 27 MHz master clock for the encoder digital ground 1 SSD1 digital supply voltage 1...
Page 190
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control R2A15220FP (AUDIO : IC471) BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB TREL ADCR SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB -∞...
Page 191
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15220FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out,...
Page 192
G G I I I I BLOCK DIAGRAM NJW1194A (AUDIO : IC484,IC489) ...
PARTS LIST OF P.C.B. UNIT z Parts indicated by "nsp" on this table cannot be supplied. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 196
Ref. No. Part No. Part Name Remarks Q'ty ELECT CAP 10UF 50V C4844 00D9430175108 CCEA1HH100T CAP , ELECT(25V/33uF) C4845 943134501580S CCEA1EH330T OTHERS PARTS GROUP WIRE ASS'Y CWB7B003100LC BN203 (3P,2.0MM,100MM,UL1569#26,105) WIRE ASS'Y LOCKING BN461 CWB1B013220HC (13P,2.0MM,220MM,UL1007#26) PIN SOCKET (15P,1.25mm,ANGLE, CN41B CJP15HJ282Z B-TO-B) PIN SOCKET (27P,1.25mm,ANGLE, CN42B...
PCB FRONT ASSY Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model EA : Australia model E1C : China model BK : Black model SP : Premium Silver model Ref.
Page 198
Ref. No. Part No. Part Name Remarks Q'ty CHIP CAP 0.1UF 50V K C6034 CCUS1H104KC C6044 COPPER WIRE C3A206 CHIP CAP 100PF 50V J C6071-6073 CCUS1H101JA CHIP CAP 0.1UF/50V/2012 C6081 CCUC1H104KC 00D9430175108 ELECT CAP 10UF 50V C6082 CCEA1HH100T CAP, CHIP(1608, C6083 CCUS1H473KC 50V/0.047uF)
PCB 7CH AMP ASSY Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model EA : Australia model E1C : China model BK : Black model SP : Premium Silver model Ref. No. Part No.
Page 202
Ref. No. Part No. Part Name Remarks Q'ty New ZD775,776 90M-HD302440R DIODE ZJ4.7B CVDZJ4.7BT RESISTORS GROUP 252310006520S PTC THEMISTORS, CRTPRF18BD471QB5RB z R7012 CHIP(95'C) 252310006520S PTC THEMISTORS, CRTPRF18BD471QB5RB z R7014 CHIP(95'C) RES, M-OXIDE R7105 CRG1SANJ102RT FILM(1W/1Kohm) RES, M-OXIDE R7108 CRG1SANJ102RT FILM(1W/1Kohm) RES, M-OXIDE R7111 CRG1SANJ332RT...
Page 203
Ref. No. Part No. Part Name Remarks Q'ty New RES, M-OXIDE R7320 CRG2SANJ153RT FILM(2W/15Kohm) RES, M-OXIDE R7321 CRG1SANJ271RT FILM(1W/270ohm) R7329,7330 943124500240S RES, M-OXIDE FLAMERETARDANT CRG1SANJ220RT FILM(1W/22ohm) 943124500050S RES,M- FLAMERETARDANT CRG2SANJR47RT R7331-7334 OXIDEFILM(2W/0.47ohm) 252310006506S PTC THEMISTORS, CRTPRF18BB471QB5RB z R7338 CHIP(115'C) RES, M-OXIDE R7405 CRG1SANJ102RT FILM(1W/1Kohm)
Page 204
Ref. No. Part No. Part Name Remarks Q'ty New RES, M-OXIDE R7620 CRG2SANJ153RT FILM(2W/15Kohm) RES, M-OXIDE R7621 CRG1SANJ271RT FILM(1W/270ohm) R7629,7630 943124500240S RES, M-OXIDE FLAMERETARDANT CRG1SANJ220RT FILM(1W/22ohm) 943124500050S RES,M- FLAMERETARDANT CRG2SANJR47RT R7631-7634 OXIDEFILM(2W/0.47ohm) 252310006506S PTC THEMISTORS, CRTPRF18BB471QB5RB z R7638 CHIP(115'C) RES, M-OXIDE R7705 CRG1SANJ102RT FILM(1W/1Kohm)
Page 205
Ref. No. Part No. Part Name Remarks Q'ty New 00D9430148708 ELECT CAP 47UF 50V E3,E1C C7125 CCEA1HH470T 943134500080S ELECT CAP 47UF 63V E2,EA C7125 CCEA1JH470T C7131,7132 943134500070S CAP , ELECT(100V/10uF) CCEA2AH100TS CHIP CAP 0.1UF 50V K C7138 CCUS1H104KC 943134010590S ELECT CAP 22UF 50V C7201 CCEA1HH220T CERAMIC CAP 470PF 50V KB...
Page 206
Ref. No. Part No. Part Name Remarks Q'ty New 943134010590S ELECT CAP 22UF 50V C7601 CCEA1HH220T CERAMIC CAP 470PF 50V KB C7602 CCKT1H471KB CHIP CAP 220PF 50V C7604 CCUS1H221JA CAP, CHIP(1608, 50V/2200pF) C7605 CCUS1H222KC 00MOA10705020 ELECT CAP 100UF 50V C7606 CCEA1HH101T CAP, PE-FILM(100V/220pF/J) C7612...
PCB MAIN ASSY Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model EA : Australia model E1C : China model BK : Black model SP : Premium Silver model Ref.
Page 208
Ref. No. Part No. Part Name Remarks Q'ty RES,M-OXIDEFILM(1W/10ohm) R7841 CRG1SANJ100RT RES, M-OXIDE FILM(2W/10ohm) R7842 CRG2SANJ100RT RES,M-OXIDEFILM(1W/10ohm) R7851 CRG1SANJ100RT RES, M-OXIDE FILM(2W/10ohm) R7852 CRG2SANJ100RT RES,M-OXIDEFILM(1W/10ohm) R7861 CRG1SANJ100RT RES, M-OXIDE FILM(2W/10ohm) R7862 CRG2SANJ100RT RES,M-OXIDEFILM(1W/2.2Kohm) R7921-7926 CRG1SANJ222RT CAPACITORS GROUP CHIP CAP 100PF 50V J C6096 CCUS1H101JA CAP , ELECT(50V/0.47uF)
Page 209
Ref. No. Part No. Part Name Remarks Q'ty ELECT CAP 4700UF 25V C9312 943134010620S CCEA1EH472E ELECT CAP 4700UF 25V C9316 943134010620S CCEA1EH472E MYLAR CAP 0.1UF 50V J C9317-9319 HCQI1H104JZT MYLAR CAP 0.1UF 50V J C9321-9323 HCQI1H104JZT OTHERS PARTS GROUP CHIP FERRITE BEAD(60ohm 4516) CLZ9Z014Z BD691 PLATE , MAIN PCB...
PCB CNT ASSY Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model EA : Australia model E1C : China model BK : Black model SP : Premium Silver model Ref.
PCB VIDEO ASSY Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model EA : Australia model E1C : China model BK : Black model SP : Premium Silver model Ref.
Page 214
Ref. No. Part No. Part Name Remarks Q'ty CHIP CAP 0.01UF 50V K C5134 CCUS1H103KC CHIP CAP 0.01UF 50V K C5136 CCUS1H103KC C5142,5143 00D9430062101 ELECT CAP 100UF 16V CCEA1CH101T CHIP CAP 0.01UF 50V K C5146 CCUS1H103KC 963134010980S ELECT CAP 47UF 16V C5147 CCEA1CH470T CHIP CAP 0.01UF 50V K...
PCB HDMI ASS'Y Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model EA : Australia model E1C : China model BK : Black model SP : Premium Silver model Ref.
PCB SMPS ASSY Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model EA : Australia model E1C : China model BK : Black model SP : Premium Silver model Ref.
Page 225
Ref. No. Part No. Part Name Remarks Q'ty z RY901 963682010370S RELAY, POWER(DC5V, 1C1P) CSL1C006ZE 963102010240S TRANS, SWITCHING(ST-4430A) CLT9Z067ZE z T9001 ZD901,902 00D2760762958 DIODE , ZENER 39V CVDZJ39BT ZD901,902 RES, CARBON(1/5W,1Mohm,J) E2,EA,E1C CRD20TJ105T 963202010440S DIODE , ZENER 22V ZD903 CVDZJ22BT 00D2760762958 DIODE , ZENER 39V E2,EA,E1C ZD903...
Need help?
Do you have a question about the AVR-2312 and is the answer not in the manual?
Questions and answers