Advertisement
ULTRA
Quick installation and programming guide
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The most recent version of this guide and the
installation manual are available at the "Downloads" section on Erreka's website:
http://www.erreka-automation.com
WARNING
The options and functions described in this guide apply for the firmware version indicated on the circuit. The
firmware, as part of a process of continuous improvement, is subject to new functionalities or upgrades being
included as a result of new versions which are not necessarily compatible with previous ones. For this reason,
some options or functions may differ or be unavailable if your firmware is older than shown in this guide.
Unlocking
should
carried out with caution.
The internal spring may
cause jolting if the barrier
is not balanced or the arm
is not mounted.
ONLY UNLOCK THE
BARRIER IF THE ARM IS
INSTALLED.
Elements of the complete installation
Unlocking
be
The drawing shows a right-side
barrier
ULS3ECD)
Electrical wiring
A: Main power supply
3x1,5mm
B: Flashing light
2x0,5mm
C: Photocells (Tx / Rx)
2x0,5mm
D: Key switch
2x0,5mm
E289A
turn the key (L) clockwise
L
until it stops.
turn the key (L) anti-clockwise
L
until locked.
D289A
English
(ULS6ECD,
ULS45ECD,
2
(max. 30m)
2
2
2
/ 4x0,5mm
(max. 30m)
2
(max. 25m)
Unlocking
(manual operation):
Locking
(motorised operation):
7
Advertisement
Table of Contents
Related Manuals for Erreka ULTRA
Summary of Contents for Erreka ULTRA
- Page 1 This quick guide is a summary of the complete installation manual. The manual contains safety warnings and other explanations which must be taken into account. The most recent version of this guide and the installation manual are available at the "Downloads" section on Erreka's website: http://www.erreka-automation.com WARNING The options and functions described in this guide apply for the firmware version indicated on the circuit.
-
Page 2: Arm Assembly
Choosing the spring and anchoring orifice Arm assembly The balancing spring and its anchoring orifice depend Choose the barrier in accordance with the assembly on the length (L) of the barrier arm: side and length of the arm: ULS6ECD: right, 100x45mm, 6m; ULS3EC Barriers: ULS45ECD: right, 100x45mm, 4.5m;... -
Page 3: Limit Switch Adjustment
Balancing the barrier THE BARRIER MUST BE BALANCED FOR PROPER OPERATION. • In order to complete the balancing, connect the power supply and check operation: the barrier Unlock should move smoothly, without jolts or jerks. • If it does not move smoothly, without any jolts or jerks, reduce the tension of the spring using the tensioning handle. -
Page 4: General Connections
F1 Motor fuse (5x20): General connections 230VAC: 2,5A 125VAC: 6,3A F2 Electronic fuse (5x20; 230VAC: 500mA) F3 FT and AUX24V outputs fuse SG.A (5x20; 315mA) DL1 Barrier open DL2 Radio code programming indicator / Receiving radio code DL3 Radio code or operation programming DL4 Opening relay enabled (photocells without testing) - Page 5 SW2 functions during programming (DIP1 = ON) DIP1=ON: programming enabled (DL3 lights up) DIP1=ON and DIP2=ON: open/close programming DIP1=ON and DIP4=ON: radio code programming E289L Radio code programming (only with RSD receiver) If a receiver other than RSD is used, see the corresponding instructions. 1 Connect electrical power...
-
Page 6: Potentiometer Adjustment
Function and mode selection using SW2 (DIP1 = OFF) Modes and functions Option Effect DIP1 the flashing light comes on and the operation begins after a 3 second warning DIP2 Advance warning the flashing light comes on and the operation begins immediately ST1: opening command;...
Need help?
Do you have a question about the ULTRA and is the answer not in the manual?
Questions and answers