Advertisement
Table of Contents
- 1 Tips
- 2 Functions Instructions
- 3 Remote Controller ON/OFF
- 4 Light ON/OFF
- 5 SUNNY, CLOUDY, MOON and CUSTOM Mode
- 6 CUSTOM Mode Setting
- 7 Set up Your Local Time
- 8 Reset Data to Factory Settings
- 9 Simulate the Effect of Lightning
- 10 CUSTOM Mode
- 11 Default Settings
- 12 Example CUSTOM Settings
- 13 Light Output
- 14 Time Table
- 15 Light Output
- Download this manual
RemoteControllerGuidance
Power Key
SUNNY Mode
CLOUDY Mode
MOON Mode
/
: modify
the value
Enter Menu
Tips:
1. The remote controller battery is shipped with partial charge which maybe out of
power during storage. Please fully charge the controller before using it. Charging
time will take approximately six hours from 0% to 100%.Do not use a computer of
any kind to charge your remote. Instead use a cell phone charger or similar USB
power supply.
2.Thebatterylifeofthedevicecanlastuptosixmonthsonafullchargeinstandby
statebutactualresultsvarydependingonhowfrequentlyyouuseitandother
settings.
Wifi Signal
POWER
CH
0
L E D
W i r e l e s si n t e l l i n g e n tl i g h t i n g
M E N U
0
O K
Channel
Time
Intensity
/
: menu switch
and selection
Confirm Key
USBConnector
Advertisement
Table of Contents
Summary of Contents for Reef Breeders Photon V2
- Page 1 RemoteControllerGuidance Wifi Signal Power Key POWER Channel SUNNY Mode CLOUDY Mode Time MOON Mode CUSTOM Mode Intensity L E D W i r e l e s si n t e l l i n g e n tl i g h t i n g : menu switch and selection : modify...
- Page 2 Functions Instructions 1. Remote Controller ON/OFF (1) Turns on: One touch of the "P POWER (2) Turns off: Touch the "Po and hold for about 3 seconds. POWER 2. Light ON/OFF (1) Light OFF: If light is on → Touch the →...
- Page 3 Functions Instructions Repeat step2 and step3 to set up your own intensity for CH-2 /-3 /-4 /-5 /-6 Step2 Step1 Step3 (3) CUSTOM Mode Setting Time is set from 0:00 to 23:00 per hour only. Before setting the CUSTOM mode, we suggest you make a graph of the values. to select CUSTOM mode.
- Page 4 Functions Instructions 4. Set up Your Local Time Step1: Press and Hold at the same time, flash Step2:Touch to select “hour” or “minute” Step3:Touch to change “hour” or “minute” 5. Reset Data to Factory Settings Press and Hold at the same time to restore the factory settings. Then M E N U POWER appears and system will automatically delete all programmed data and return the...
-
Page 5: Default Settings
Default Settings CUSTOM mode Mode CH-1 CH-2 CH-3 CH-5 CH-6 CH-4 0:00 1:00 2:00 3:00 4:00 5:00 6:00 7:00 8:00 9:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00 SUNNY, CLOUDY, MOON and MANUAL mode Mode CH-1 CH-2... - Page 6 Example CUSTOM Settings Example Graph of Time table 1 : Hour to start light is 9:00 Channel 1 Channel 3 Channel 2 Channel 4 Channel 5 Channel 6 Time Deep Red Royal Blue Green Cool White Cool Blue Violet 9:00 10:00 11:00 12:00...
- Page 7 Example CUSTOM Settings Example Graph of Time table 2 : Hour to start light is 9:00 Channel 1 Channel 3 Channel 2 Channel 4 Channel 5 Channel 6 Time Deep Red Royal Blue Green Cool White Cool Blue Violet 9:00 10:00 11:00 12:00...
Need help?
Do you have a question about the Photon V2 and is the answer not in the manual?
Questions and answers