Advertisement
Table of Contents
- 1 Table of Contents
- 2 Safety Instructions
- 3 Introduction
- 4 Precautions for Operation
- 5 Installation, Piping and Wiring
- 6 BLEED VALVE INSTALLATION (Optional)
- 7 CURRENT INTERRUPTOR (Optional)
- 8 Maintenance
- 9 Service and Repairs
- 10 Troubleshooting
- 11 Parts List (Exploded Pump Assembly)
- 12 Replacement Kits (Exploded Wet End Assembly)
- Download this manual
Advertisement
Table of Contents
Related Manuals for Pulsafeeder Chem-Tech 100 Series
Summary of Contents for Pulsafeeder Chem-Tech 100 Series
- Page 1 READ ALL CAUTIONS CAREFULLY BEFORE INSTALLING PUMP INSTRUCTION MANUAL P/N 32040 Rev C...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page SAFETY INSTRUCTIONS ............................2 INTRODUCTION ................................ 2 PRECAUTIONS FOR OPERATION .......................... 3 INSTALLATION, PIPING AND WIRING ........................4 BLEED VALVE INSTALLATION (Optional) ....................... 6 CURRENT INTERRUPTOR (Optional) ........................7 MAINTENANCE ................................. 8 SERVICE AND REPAIRS ............................9 TROUBLESHOOTING ............................. -
Page 3: Precautions For Operation
No agent of ours is authorized to make any warranty other than the above. For warranty and service matters within the European Union, contact the seller first or: Pulsafeeder, Inc. Europe Units 12 and 13, Edison Road... -
Page 4: Installation, Piping And Wiring
10. Standard white polyethylene discharge tubing is not recommended for installations exposed to direct sunlight. Consult supplier for special black polyethylene tubing. 11. Manufacturer will not be held responsible for improper installation of pumps, or local plumbing conducted. All cautions are to be read thoroughly prior to hook-up and plumbing. For all installations a professional plumber should be consulted. - Page 5 Flooded suction mounting Fig. C (installing feeder at the base of tank on a platform) is the most trouble free type of installation. (Tank stands and platforms are available for all size feeders and tanks). The pump is secured on the platform, and then the clear suction tubing is attached to a bulkhead fitting assembly and the suction valve housing on the pump head.
-
Page 6: Bleed Valve Installation (Optional)
DOWN-THE-WELL INSTALLATION: Often it is desirable to provide chemical feed near the intake of the well pump for additional retention time and mixing of the chemicals. An additional length of discharge tubing will be required for this installation. Secure the end of the discharge tubing to the pump cylinder, drop pipe, or foot valve and lower it into the well. -
Page 7: Current Interruptor (Optional)
7. Return the system to operating conditions and reconnect the power to the pump. The pump is now ready for priming and operation. Always use caution and check for leaks at newly assembled connections. CURRENT INTERRUPTER: (optional) CURRENT INTERRUPTER ON/OFF CYCLE TIME DIAL SET AT: RUN TIME OFF TIME... -
Page 8: Maintenance
PRIMING All pumps are tested with water (e.g. sulfuric acid, polymer) the pump head should be removed and dried thoroughly along with the diaphragm and valve seats. If the discharge line is connected directly to a pressurized system it should be temporarily bypassed during priming of the pump. -
Page 9: Service And Repairs
4. When light finger pressure will no longer allow movement of the knob between cam contacts, grasp the knob securely and tighten the locking lever (turning clockwise) making sure that the knob does not move. To check for zero point, turn on pump. -
Page 10: Troubleshooting
TROUBLESHOOTING PROBLEM PROBABLE CAUSE REMEDY 1. Pump setting too low. 1. Adjust to higher setting (feeder must be operating during the stroke length adjustment). LOSS OF 2. Scale at injection point 2. Clean injection parts with 8% muriatic acid or undiluted vinegar. CHEMICAL 3.
Need help?
Do you have a question about the Chem-Tech 100 Series and is the answer not in the manual?
Questions and answers