WAGNER CONTROL PRO 250 M Operating Instructions Manual
Universal sprayer
Hide thumbs
Also See for CONTROL PRO 250 M:
- Manual (145 pages) ,
- Owner's manual (100 pages) ,
- Translation of the original operating instructions (137 pages)
Related Manuals for WAGNER CONTROL PRO 250 M
Summary of Contents for WAGNER CONTROL PRO 250 M
- Page 1 UNIVERSAL SPRAYER CONTROL PRO 250 M ORIGINAL- BETRIEBSANLEITUNG wagner-group.com...
- Page 2 Control Pro 250 M HIGH EFFICIENCY AIRLESS CONTROL PRO 100 BETRIEBSANLEITUNG wagner-group.com ...
- Page 3 Control Pro 250 M SPRAY PRIME 0 = OFF PRIME SPRAY ...
- Page 4 Control Pro 250 M 20 - 25 cm 20 - 25 cm 20 - 25 cm 20 - 25cm ...
- Page 5 Control Pro 250 M HOUSEHOLD...
- Page 6 Before any work is done on the unit or for every break in work the following rules must be observed: 1. Release the pressure from spray gun and hose. 2. Secure the WAGNER spray gun using the safety catch on the trigger. 3. Switch o unit.
-
Page 7: Explanation Of Symbols Used
Control Pro 250 M Congratulations on your purchase of a WAGNER colour application device. You have purchased a proprietary device that requires careful cleaning and care to ensure trouble-free functioning. Read the operating instructions carefully before using the tool and observe the safety instructions. Keep the operating instructions in a safe place. -
Page 8: Flammable Materials
Control Pro 250 M 3. Safety of Persons a) Be attentive. Pay attention to what you are doing and work sensibly with a power tool. Do not use the tool if you are tired or under the influence of drugs, alcohol or medication. Just a moment of inattentiveness while using the tool can lead to serious injuries. -
Page 9: Explosion Protection
Control Pro 250 M Explosion protection Do not use the unit in work places which are covered to the explosion protection regulations. Danger Danger of explosion and fire through sources of flame during spraying work There may be no sources of flame such as, for example, open fires, smoking of cigarettes, cigars or tobacco pipes, sparks, glowing wires, hot surfaces, etc. -
Page 10: Connecting The Device
197 kΩ/m (60 kΩ/ft.). For reasons of function, safety and durability, only use genuine WAGNER high-pressure hoses and spray nozzles. For overview see „Spare parts lists“. -
Page 11: Field Of Application
Preparation of the Coating Material Using Control Pro 250 M interior wall paints, varnishes and glazes can be applied by spraying without diluting them, or by diluting them slightly. Detailed information is available in the technical data sheet of the manufacturer ( Internet download). -
Page 12: Spray Gun
Control Pro 250 M Thinning recommendation Sprayed material Glazes undiluted Wood preservatives containing solvents or based on water, mordants, oils, disinfection agents, plant undiluted protective agents Paints containing solvents and watersoluble paints, primers, vehicle coating paints, thick-film glazes dilute by 5 - 10 %... -
Page 13: Spray Technique
Control Pro 250 M Start-up Before connecting to the mains supply, be sure that the supply voltage is identical with the value given on the rating plate. 1. Disconnect the return hose from the suction hose. 2. Place the suction hose (Fig. 11, 1) in the material container and the return hose (Fig. 11, 2) in an empty container. -
Page 14: Interruption Of Work
Control Pro 250 M 4. Release the trigger and secure the gun. Reverse the nozzle so the arrow points forward again. Unlock the gun and resume spraying. Interruption of Work Be sure to follow the Pressure Relief Procedure when shutting the unit off for any purpose. -
Page 15: Maintenance And Repairs
Control Pro 250 M Maintenance and repairs Before carrying out any work on the device, relieve the pressure and unplug the power plug from the socket. Danger a) Cleaning the inlet valve If any problems occur when the paint is sucked up, the intake valve needs to be cleaned or replaced. Problems can be avoided by cleaning and servicing the device properly. -
Page 16: Information About The Oscillation Level
Filter, white (nozzle 517/619, 2 pack) 0418 713 Gun extension (30 cm) 0517700 Oil (118 ml) 2319722 Further information about the WAGNER range of products for renovating is available under www.wagner-group.com Technical Data Pump type Piston pump Power source 230 V... -
Page 17: Correction Of Malfunctions
Control Pro 250 M Correction of Malfunctions Problem Cause Remedy • The sprayer does The sprayer is not plugged in. ➞ Plug the sprayer in. • not start. The device is switched off. ➞ Turn the ON/OFF switch to ON (I). - Page 18 If the check shows that the case is not a guarantee case, repairs are carried out at the expense of the buyer. Claims against Wagner that are based on or caused by the failure or insufficiency of a unit cannot be asserted.
- Page 19 Control Pro 250 M Warning If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because special purpose tools are required. The wires in this mains lead are coloured in accordance with the...
- Page 20 Errores y modificaciones reservados. Salvo erros e alteraçŏe. Vi tager forbehold for eventuelle fijl og ændringer. Part. No. 2372675 Vi påtar oss inget ansvar för eventuella felaktigheter 12/2016_RS och förbehåller oss rätten att utföra ändringar. © Copyright by J.Wagner GmbH...
Need help?
Do you have a question about the CONTROL PRO 250 M and is the answer not in the manual?
Questions and answers