Download Print this page
ZOLL AED PLUS Trainer2 Operator's Manual

ZOLL AED PLUS Trainer2 Operator's Manual

Automated external defibrillator

Advertisement

Quick Links

TROUBLESHOOTING
AED Trainer problem / display:
Action:
Trainer2 does not respond
Replace all four "D" batteries
(green light in status window
in Trainer2 unit.
is not lit) when On/Off
button is pushed
On
Off
Remote Controller does not
respond (scenario
Replace both "AA" batteries in
selection is not lit)
Remote Controller.
when view/enter
button is pushed
Trainer2 does not beep or
Re-set scenario and make
react to Remote Controller
certain that CPR metronome
during CPR interval.
light is on.
Unit is configured for ERC.
Change to AHA configuration.
No prompt to "GIVE TWO
(See Chaning AHA/ERC
BREATHS" after "CHECK
Configurations section of this
BREATHING"
Operator's Guide).
With new batteries in both,
Contact ZOLL
Trainer2 fails to respond to
Technical Service
Remote Controller
MAINTENANCE
1.
Keep Trainer2 and Remote Controller clean, undamaged,
and free of excessive wear.
2.
Verify that there are no cracks or loose parts in Trainer2 and
Remote Controller.
3.
Replace Training electrodes as necessary.
CLEANING
Clean the Trainer2 unit and remote controller with soft, damp
cloth using soap and water, then wipe dry immediately.
Do not immerse any parts in water.
Do not clean with ketones (e.g., MEK, acetone).
Avoid using abrasives on any surface.
Do not sterilize the Trainer2 or the Remote Controller.
WARNING
Product intended for indoor use only.
This device is for training only. It will not deliver
WARNING
defibrillation energy.
Do not attempt to plug AED Plus or AED Pro
WARNING
simulator into connector of Trainer2.
Do not attempt to take Trainer2 or Remote
WARNING
Controller apart. Remove and replace battery
compartment doors only and replace
immediately.
CPR FEEDBACK OPERATION
The AED PLUS Trainer2 includes controls that allow instructors to simulate
the voice prompts and text messages issued by the AED PLUS when
rescuers perform CPR. These controls include:
Remote Controller:
Description:
CPR Metronome On/Off
This control activates the Trainer2's metronome
which begins to beep at 60 compressions per minute
(CPM) then automaticallyaccelerates to 100 CPM
after a few seconds. Metronome beeps are inde-
pendent of the student's actual compression rate
and continue until the CPR interval times out or until
the Metronome On/Off button is pressed again. The
control and the metronome functions are only active
during periods when the Trainer2 has prompted
the rescuer to perform CPR
PUSH HARDER Button
Pressing this control button causes the Trainer2 to
emit a single "PUSH HARDER" voice prompt.
Instructors should depress this button when the
student's chest compressions are too shallow.
Good Compressions Control
Pressing this control button causes the Trainer2 to
emit a "GOOD COMPRESSIONS" voice prompt. To
simulate operation of the AED PLUS defibrillator,
instructors should use this control to provide
students with positive feedback about improve-
ments in chest compression depth when they
respond to "PUSH HARDER" prompts.
SWITCHING AHA/ERC CONFIGURATION
American Heart Association (AHA) configuration: Prompt to "GIVE TWO
BREATHS" after "CHECK BREATHING".
European Resuscitation Council (ERC) configuration: NO prompt to "GIVE
TWO BREATHS" after "CHECK BREATHING".
Prompt to "GIVE TWO BREATHS" can be configured into (AHA configuration),
or out of (ERC configuration) the prompt sequence by doing the following:
With the Trainer2 unit off, hold down the Shock Button. Press On/Off Button
once. Green light will illuminate at status window to indicate AHA config-
uration (prompt sequence will contain "GIVE TWO BREATHS").
Press On/Off Button again. Green light will turn off and red light will illuminate
at status window to indicate ERC configuration (prompt sequence will NOT
contain "GIVE TWO BREATHS").
Press On/Off Button again to revert to AHA configuration (green light on
and red light off).
When configured as desired (green = AHA, red = ERC), hold down On/Off
button to turn unit off and store configuration.
NOTE
Extra and/or replacement Remote Controllers are available
Contact your distributor or ZOLL Medical.
Trainer
.
Automated External Defibrillator Trainer2
Operator's Guide
2
For technical support or repair:
Technical Service Department
ZOLL Medical Corporation
269 Mill Road
Chelmsford, MA USA 01824-4105
978-421-9655
800-348-9011
Fax: 978-421-0010
© ZOLL Medical Corporation 2007
TRAINING USE ONLY - NOT FOR CLINICAL USE
REF 9650-XXXX-XX Rev. A

Advertisement

loading
Need help?

Need help?

Do you have a question about the AED PLUS Trainer2 and is the answer not in the manual?

Questions and answers

Summary of Contents for ZOLL AED PLUS Trainer2

  • Page 1 CPR FEEDBACK OPERATION AED Trainer problem / display: Action: The AED PLUS Trainer2 includes controls that allow instructors to simulate the voice prompts and text messages issued by the AED PLUS when Trainer2 does not respond rescuers perform CPR. These controls include: Replace all four “D”...
  • Page 2 Action: Trainer2 unit: Action: The Remote Controller controls all prompts when Install 4 “D” batteries in the AED Plus Trainer2. Scenario Set-up Controls: the Trainer2 is beeping (during the CPR interval). Press On/Off button to turn Trainer2 on. Press the PUSH HARDER button during the CPR interval to force the unit to say “Push Harder”.