Genie GK-R Instructionsfor Use

Wireless Keypad Instructions
For use with Genie Intellicode® garage door openers
Scan this code with a QR code reader app
on a smart device to view a video of these
instructions or visit www.geniecompany.com
Keypad Overview
!
Program Key
MOVING DOOR CAN CAUSE SERIOUS
LED O
LED
• DO NOT install transmitter (keypad) unless the door operator's
LED On safety device works as required by the door operator's manual.
Keypad • Wall Console must be mounted in sight of door, at least 5 feet
above floor and clear of moving door parts.
• Keep people clear of opening while door is moving.
• DO NOT allow children to play with the transmitter or door
operator.
LED Flashing
If safety reverse does not work properly:
Up/Down Key
• Close door then disconnect opener using the manual release
(enter)
handle.
• DO NOT use transmitter or door operator.
• Refer to Door and Door Opener Owner's Manuals before
attempting any repairs.
AVERTISSEMENT
!
DÉMÉNAGEMENT PORTE PEUT CAUSER DES
BLESSURES GRAVES OU LA MORT.
• NE PAS installer le transmetteur (clavier) à moins que le dispositif
Keypad O Keypad On Keypad Flashing
de sécurité de l'opérateur de porte ne fonctionne comme l'exige le
manuel d'utilisation de la porte.
• Console murale doit être monté en vue de la porte d'au moins 5
Activate keypad by opening battery
pieds au-dessus-de-chaussée et claire des pièces mobiles de la
compartment and pull protective
porte.
tab. Reinstall compartment door to
• Garder les personnes clair de l'ouverture lorsque la porte est en
begin programming. mouvement.
• Ne pas laisser les enfants jouer le premier match à distance ou la
porte.
SAVE THESE
Si la sécurité inverse ne fonctionne pas correctement:
TAB
• Fermer la porte, puis débranchez moteur à l'aide de la poignée de
INSTRUCTIONS
déverrouillage manuel.
FOR FUTURE
• Ne pas utiliser d'ouverture à distance ou la porte.
USE
• Reportez-vous à la porte et ouvre-porte de propriétaires manuels
avant de tenter toute réparation.
It is recommended to complete programming before mounting keypad
Keypad LED's
Successful Entries
Keypad LED will flash each time Keypad LED and PROGRAM key
a key is pressed and entry is will flash slowly and number pad
accepted. back light will remain on for 15
seconds indicating a successful
program or valid PIN has been
entered.
38832503793 01/2018
STEP 1) PROGRAM THE NEW KEYPAD TO THE OPENER
Activate keypad by opening battery compartment and
pull protective tab. Reinstall compartment door to begin
programming.
The existing factory default Personal Identification Number
(PIN) for this keypad is the number sequence: 3-5-7
Sync the opener and the keypad by performing the
following:
1. Ensure the keypad back lighting is off.
WARNING
2. Place garage door opener into PROGRAMMING MODE
as illustrated in the column to the right.
3. Press 3-5-7 in sequence on the keypad.
INJURY OR DEATH.
4. Press the UP/DOWN key 3 to 4 times slowly until
garage door opener operates.
• This completes the programming of a single door
opener (door 1) and keypad.
• IT IS RECOMMENDED THAT YOU CHANGE THIS PIN FROM THE
EXISTING FACTORY DEFAULT SETTING of 3-5-7. See STEP 2 below.
STEP 2) CHANGING THE FACTORY DEFAULT PIN OF 3-5-7:
1. Enter the factory default pin of 3-5-7.
2. Press PROGRAM key once.
3. Enter a new PIN of your choice (3-8 digits).
4. Press PROGRAM key once.
• Your PIN has been changed and your previous PIN will no
longer operate the keypad or opener.
STEP 3) OPTIONAL:
PROGRAMMING THE KEYPAD FOR MULTIPLE OPENERS (UP TO 3)
Whether the keypad is brand new or you are just adding
additional openers to an existing keypad, this STEP assumes
that STEPs 1 & 2 have already been completed.
Follow these steps to program opener 2 and/or 3 to the
keypad. (Only one PIN number can be used.)
1. Ensure the keypad back lighting is off.
2. Enter the current PIN.
3. Press PROGRAM key twice. LED will blink once per
second.
4. Enter total number of openers that keypad will be
operating (a total of "2" or "3" openers).
5. Press PROGRAM key once. LED will blink twice and shut
off.
• If LED did not blink twice and shut off, please see
RESETTING THE KEYPAD (FACTORY DEFAULT) section.
• THE KEYPAD IS NOW READY TO PROGRAM TO MULTIPLE
Failed Entries GARAGE DOOR OPENERS. CONTINUE WITH THE STEPS
BELOW.
PROGRAMMING TO MULTIPLE OPENERS CONTINUED
1. Ensure the keypad back lighting is off.
2. Place desired garage door opener (for door 2 or 3) into
PROGRAMMING MODE as shown to the right.
3. Enter the PIN number on keypad.
4. Press the UP/DOWN key once.
Keypad LED, PROGRAM key and
5. Press the number of the desired door (door 2 or 3).
number pad back light will flash
6. Press the UP/DOWN key 3-4 times slowly until garage
rapidly indicating a problem with
door opener operates.
programming or an invalid PIN entry.
• Repeat steps 1 through 6 in this section to program
• Wait 15 seconds until back lighting
another door opener to this keypad (maximum of 3 doors
shuts off and enter a valid PIN or
to 1 keypad).
reset keypad to reprogram.
• This completes programming of multiple doors. See STEP
4 MULTI-DOOR OPERATION for further instruction.
STEP 4) OPERATING THE KEYPAD WITH THE OPENER(S)
PUTTING OPENER INTO PROGRAMMING MODE:
Single Door Operation:
Current Production Openers
1.
2.
+ + + + 3.
PRGM PRGM PRGM
PRGM
4.
– –
– SET SET
SET
SET
Multi-Door Operation:
TYPE 4
TYPE 1 TYPE 2 TYPE 3
1.
There are 4 types of programming button pads. Type 1 2.
is shown in these steps. All buttons perform the same
3.
function and programming is the same for all types shown
4.
above.
5.
Place operator into programming mode: TYPE 1-2-3-4
NOTE: Keypad will remain active for 15 seconds after a
1. Press and hold the program button until the round
successful entry is made. During this 15 seconds ANY key will
LED turns blue, then
PROGRAM PROGRAM operate the opener.
release.
+ +
SET SET
2. The round LED will go out and the long LED will begin
STEP 5) MOUNTING THE KEYPAD
flashing purple.
Keypad MUST be mounted within sight of the garage
PROGRAM PROGRAM
door(s) at least 5 feet above floor and clear of any moving
3. Return to previous + +
SET SET
door parts.
STEP.
-OR-
•
Openers manufactured between 1995 to
1. Remove battery cover and batteries.
2011 and all external receivers
NOTE: Learn Code Buttons are normally located under lens
covers on earlier models.
Place operator into programming mode:
1. Press & release Learn Code button once. The red LED
will begin to flash.
2.
3.
LEARN
RADIO
OPEN
or LEARN MANUAL SET LIMIT FORCE
SIGNAL SET
CODE CLOSE
LEARN
4.
CODE
CODE
RADIO
SIGNAL
RADIO
LEARN SIGNAL
CODE
LEARN
CODE
2. Return to previous STEP.
NOTE: The openers LEARN LED will time
5.
out in 30 seconds. Programming must be
6.
completed within 30 seconds.
* RESETTING THE KEYPAD (FACTORY DEFAULT):
If the keypad has already been programmed or at any
time the programming should be erased and started from
the factory default, follow these steps.
1. Ensure that number pad back lighting is off.
2. Press and hold the PROGRAM and UP/DOWN Keys
together for approximately 5 seconds.
3. The LED will flash twice and all lights will go out
indicating the keypad has been reset.
4. Start at STEP 1 to sync the keypad to an opener.
REPLACING BATTERIES
If the keypad back lighting fails to operate batteries may
Ensure number pad back lighting is off.
require replacement.
Enter PIN.
• Programming will not be lost during battery change.
Press the UP/DOWN key.
Opener will operate.
Ensure number pad back lighting is off.
Enter PIN.
Press the UP/DOWN key.
1. Remove battery cover and batteries.
Press number key corresponding with desired door
2. Replace batteries with same type alkaline (AAA) and check
(1, 2, or 3).
for proper direction of (+) and (-) terminals.
Desired opener will operate.
Rechargeable batteries are NOT recommended.
ADDITIONAL (OPTIONAL) PROGRAMMING:
Changing an Existing PIN:
1. Enter current PIN
2. Press PROGRAM key once.
3. Enter new PIN (3-8 digits)
4. Press PROGRAM key once.
Programming will not be lost during battery removal.
• Your PIN has been changed and your previous PIN will no
longer operate keypad or opener.
Setting a Temporary PIN:
A temporary PIN allows temporary access to the garage
by normally unauthorized personnel such as repairmen or
neighbor.
1. Enter current PIN.
2. Press PROGRAM key 3 times.
3. Enter a temporary PIN (3 to 8 digits)
4. Press PROGRAM key once.
Drill a 3/32" pilot hole for the top mounting screw.
• The Temporary PIN will operate garage door opener until
Install included screw into pilot hole, leaving 1/8" gap
the original PIN is used. Use of the original PIN will delete
between the screw head and wall.
temporary PIN.
Hook the slotted mount on back of keypad over the
screw.
For questions, comments or troubleshooting, contact The
Genie Company at:
1/8"
Screw
head gap 1 Door Drive, Mount Hope Ohio, 44660
Wall
or call 1-800-354-3643 or visit our website at:
www.geniecompany.com
Mark and drill a 3/32" pilot hole for the bottom screw FCC Part 15.21 Statement:
Changes or modifications not expressly approved by the party
and secure keypad to the wall. (Do not over-tighten).
responsible for compliance could void the user's authority to operate
Reinstall batteries.
the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.