Girafus 227PA User Manual

Pet Tracker 227PA User Guide
1
INTRODUCTION
The Pet Tracker 227PA consists of a remote unit for the owner and
transmitter tag that easily attach onto your pets collars via a specially
designed water splash proof silicone case. In the unfortunate case of
losing sight of your pet, the Pet Tracker 227PA can help track your pet
down within a range of up to 500 meters.
KEY FEATURES
- Helps you track down up to 4 pets should they go missing
- Directional tracking to guide you in the right direction
- Uses safe 2.4 GHz RF technology, will not interfere other wireless devices
- Water splash ressistant case for outdoor activites
- Smart sleep mode for longer battery life of up to two months
- Easily attaches to most collars including a velcro strap for larger collars
- Special Data Encryption so you won't detect other pets
- Rhythm Buzzer- the closer you are to your pet, the faster the rhythm is
- Track by sound, tag beeps to help you zero in their hidden location
- Easy installation, insert battery, turn on, and you are good to go
- Multi application, can be used on pets, keys, bags, and even the kids
SPECIFICATIONS
Func on
Search range
Communica on Standard
Remote / Tag unit specs
Ba ery type
Ba ery life me with search
( 10 mins a day )
Beep Sound (at 10cm/3.9inch)
Dimension (L/W/H) in mm
Working environment
2
GETTING STARTED (example for 227PA2, 1 base to 2 tags)
This section shows how setup your Pet Tracker and do a one-off calibration
process.
BATTERY FITTING
1. Insert the batteries into the Remote unit and the available Tag units.
- Slide out (remove) the battery covers on the Remote and Tag Units.
- Insert batteries (included) according to the polarity markings (+/-) in
the battery compartments.
- Replace the battery compartment covers on both units.
2. Tag unit will flash for 30 seconds and enter sleep mode.
Remote unit
Install Battery
Remove Cover
Replace Cover
TESTING
1. Place the White Tag unit in a stationary location.
2. With the Remote base unit in hand, walk away from the Tag. At about
20~30 meters outside turn ON the Remote.
3. Once the remote base unit is turned on to start search the White Tag, this
will enable a green flash and initiate a slow tracking rhythm.
4. Now start walking back towards the tag, you should hear a increased
rhythm and get max signal rhythm when within 10~15 meters of the tag.
5. Press and hold the button "1" to activate the tag to chirp to allow tracking
by sound. Once the search is done, turn off the remote.
6. Place the Tag into the silicone case and attach the case onto your pet's
collar . If the collar is too wide to fit into the silicone case vents, please
use the provided velcro strap and fit the case onto the strap.
7. To test the second Tag (Black), just do the same steps as select button
"2" after turning on the Remote unit.
Note: You may turn the remote base unit off when not in use to save
battery. Turn back on when searching is required.
Searching & Tracking 1 to 4 Tags
0~500 meters (*Distance will vary depending
on terrain and other factors)
Digital 2.4 GHz RF (Frequency range: 2.40 - 2.48MHz)
Remote unit Tag unit
AAA x 2 CR 2032x1 or LIR 2032
CR 2032: 30 days
150 days
LIR 2032: 15 days
92db ± 3 db 85db ± 3 db
38x25x11 mm
95x65x14mm
˚C ˚C
With CR2032 Ba ery: Temp. 5 ∼40 、humi. 20％∼80％
˚C ˚C
With LIR2032 Ba ery: Temp. -15 ∼40 、humi. 20％∼80％
Page 1
Tag unit
Page 3
PACKAGE CONTENTS (227PA2)
Model Name Base Unit
1 piece
Remote Unit
Tag Unit
Batteries AAA x 2 pieces
Strap 1 piece
1 piece
Hook
Silicon Sleeve
Velcro strap
1 piece
User manual
OVERVIEW
Remote Unit
Front
1
5
6
7
2
8
3
4
Tag Unit
Front
1
2
3
4
SUGGESTED LOCATION TO PLACE BASE / TAG units
Remote Unit
ADDITIONAL OUT OF RANGE NOTES (MUST READ)
1. When in Search mode, and if remote doesn't find tag, the Remote unit will
flash red continuously for over 30 seconds and give one last beep before
entering sleep mode. If this is the case, press the search button
no.(1,2,3 or 4) once to enter the search mode as you walk and search the
area for a signal.
2. When the tag is within range, the remote base unit will show a green light
and start a tracking tone within 15 seconds. Start walking in different
directions until one direction gives you an increase beeping frequency, that
way you know you are walking in the right direction. DO NOT turn in circles
on the same spot, keep walking in different directions until the beep tone
speeds up.
MANAGING ALL 4 TAG UNITS FROM THE BASE UNIT
The Remote unit will always start searching for tag 1 (White tag) when it is
turned on. To search for the second tag (black) press button "2" and the
remote unit will start searching for the second tag while button 3 and 4 are
for the third and fourth. If the tag you are searching for isn't in range the
status light will flash continuously with no signal or tracking tone. After 15
seconds it the Remote unit will chip and go to sleep mode until you press to
track the tags again.
When not tracking, turn off Remote unit to save power.
White Black
Tag Unit (base on purchased model)
2 pieces
CR2032 x 2 pieces
2 pieces
2 pieces
1
Strap attachment
Back
2 Search status
9
3
Power switch
4 Search button
5 Direction indicator
10
6 Set button
Signal strength lights
7
8 Mute switch
Speaker
9
11
10
Clip
11 Battery cover
Back
1 Hanging hole for strap
Buzzer
2
3 Top cover
4 LED (Connection status)
Bottom cover
5
6
Tag Unit
Page 2
(Note: #3 & #4 tags OPTIONAL)
Search Status Light
Search Buttons
Page 4