Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Prince Manuals
  4. Robotics
  5. T8840
  6. Owner's manual

Prince T8840 Owner's Manual

Hide thumbs

Advertisement

Available languages

Available languages

Quick Links

Download this manual
O W N E R ' S M A N U A L
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before
assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 2 to identify and sort all fasteners. Check all
cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may
not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, one 3/8" Wrenches, Two 7/16" Wrenches (Ratchet and 3/8", 7/16"
Sockets are recommended and can be substituted for wrenches), Rubber Mallet or Hammer.
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could
over-tighten the and strip the screws out of the wooden table top.
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be
contacted for replacement parts.
Please Do Not Return This Product To The Store!
Contact Escalade
Phone:
1-866-873-3528
Fax:
1-866-873-3533
E-mail:
tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at:
ON-LINE TROUBLE SHOOTING
ON-LINE PARTS REQUESTS
ADDITIONAL ESCALADE
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
®
Sports customer service department at:
®
SPORTS PRODUCT INFORMATION
Toll – Free !
Toll – Free !
www.escaladesports.com
TECHNICAL ASSISTANCE
FREQUENTLY ASKED QUESTIONS
TABLE TENNIS TABLE
MODEL NUMBER
T8840
2L-4239-00
2015 Escalade Sports

Advertisement

loading
Need help?

Need help?

Do you have a question about the T8840 and is the answer not in the manual?

Questions and answers

Related Manuals for Prince T8840

Summary of Contents for Prince T8840

  • Page 1 TABLE TENNIS TABLE MODEL NUMBER T8840 O W N E R ' S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering parts.
  • Page 2 Sorting your hardware ahead of time will speed up assembly time. Sort all your NOTE: hardware now so it will be ready before you start assembly. (Qty. 6) (Qty. 4) S.M.S. (Qty. 4) (Qty. 2) (Qty. 4) (Qty. 4) 1/4-20 x 3 1/4 Hex Head Bolt 1/4-20 Zinc Locknut (Qty.
  • Page 3 Table top can be set on two saw horses. Although this will make assembly easier it is not necessary to complete assembly. Always use shipping container to protect the painted surface of the table top. CAUTION: Make sure that the table top is secure on the ASSEMBLY TIP sawhorses and NEVER leave the table top unattended.
  • Page 4 End Rail Mounting Indentations CAUTION: IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS! CAUTION: WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS (#3) BE TURNED AS SHOWN HERE.
  • Page 5 HARDWARE NEEDED #8 X 7/16” Screw (Qty. 20) 4. Align the holes in the Mounting Brackets #33 & #34 with Indentations in table top assembly and secure with screws #20 as shown. All holes in each Mounting Bracket must align with Indentations in the top.
  • Page 6 HARDWARE NEEDED #10-24 X 1/2 Locknut (Qty. 2) 1/4” Locknut Leg Brace #10-24 X 1/2 Phillips (Qty. 2) Pan Head Screw (Qty. 2) 1/4-20 x 2 1/4 Hex Head Bolt Plastic Washer (Qty. 2) (Qty. 4) 5. Attach Legs (#2) to Mounting Bracket (#34) with Hex Bolt (#38), two Plastic Washers (#24) and Locknut (#15).
  • Page 7 HARDWARE NEEDED #8-32 X 1 1/4 Phillips Head Screw (Qty. 2) Note: To aid in assembly use a cordless drill and Phillips bit, but be careful to not strip the screws. Wear safety glasses for Step 7. Note: Rotate U-Support #7 until you see the screw hole in the Figure slot of U-clip #3.
  • Page 8 BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS! Note: Rails attach HARDWARE NEEDED with #20 screws Note: Prince #8 x 1 7/16 logo must be on Sheet Metal Screw this end of Rail.
  • Page 9 HARDWARE NEEDED HARDWARE NEEDED Plastic Washer 3/4” Spacer 1/4-20 x 2 1/2 Hex Head Bolt (Qty. 2) (Qty. 2) 1/4” Locknut (Qty. 1) (Qty. 3) 5/16” Spacer 1/4-20 x3 1/4 Hex Head Bolt (Qty. 2) 1/4-20 x 1 1/2 Bolt (Qty.
  • Page 10 NOTE: DO NOT HIT CASTER SOCKET #12 DIRECTLY WITH A HAMMER! SET A PIECE OF WOOD ON CASTER SOCKET AND HIT PIECE OF WOOD TO DRIVE CASTER SOCKET INTO U-SUPPORT #7. 16. Gently tap caster sockets #12 into U- support #7 until flange on sockets Note: This is the end of the touches the edge of the tube.
  • Page 11 HARDWARE NEEDED CAUTION: Logo on #5 panel AT LEAST TWO ADULTS ARE NEEDED TO MOVE TABLE HALF! 1/4-20 x 1 1/4” Bolt faces out (Qty. 4) ¼” Locknut Logo on (Qty. 8) #5 panel faces out 1/4-20 x 1 1/2 Bolt (Qty.
  • Page 12 HARDWARE NEEDED CAUTION: AT LEAST TWO ADULTS ARE NEEDED TO MOVE TABLE HALF! Plastic Washer (Qty. 2) 1/4-20 x 2” Hex Head Bolt (Qty. 2) ¼” Locknut (Qty. 2) 22. Repeat steps from 1-17 on second half then continue on Step 23. NOTE: Tighten locknuts #15 finger tight 23.
  • Page 13 HARDWARE NEEDED 1/4” Locknut (Qty. 2) Figure 9 1/4-20 x 1 1/2 Bolt (Qty. 2) 24. Make sure the legs on the first table top half (the half with the name panel #5) are open. With one person on each side of the table, lift and set table half on its legs. Place table against a wall as shown above to help stabilize table top half while second half is being attached.
  • Page 14 Figure 10 Detail J Hardware Needed #10-24 Lock Nut (Qty. 2) #10 Flat Washer (Qty. 2) #10-24 X 3/4 Round Head Screw (Qty. 2) Detail K INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE OF CAUTION: TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE! 27.
  • Page 15 29. Secure net posts to center of table by turning the screw on net posts as shown in picture A. 30. Slide Paddle Holder onto net post as shown in picture B. 31. Insert “Slide Lock” into Paddle Holder channel. See Picture C. Repeat Steps 29-31 for other net post.
  • Page 16 OPENING AND CLOSING INSTRUCTIONS READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS CAUTION: TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.

  • Page 17: Care And Maintenance

    90 DAY LIMITED WARRANTY ® This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of ninety (90) days from the original purchase.
  • Page 18 REPLACEMENT PARTS LIST FOR MODEL NUMBER T8840 Key# Part # Description Qty. TABLE TOP 4A-5522-00 LEG & BRACE ASSEMBLY 1A-7894-00 1” U-CLIP 2S-6879-10 LINKAGE 8S-6758-05 NAME PANEL 2S-6422-34 SAFETY STRAP 2S-6428-01 8S-6606-05 U-SUPPORT SAFETY LATCH 2S-6264-03 1/4-20 X 1 1/2 HEX HEAD BOLT WB-1094-00 #10-24 X 3/4 PHILLIPS ROUND HD.
  • Page 19 *PARTS LIST ON PREVIOUS PAGE. 2L-4239-00...
  • Page 20 MESA DE TENIS NÚMERO DE MODELO T8840 M A N U A L D E L U S U A R I O 1. Lea este manual cuidadosamente antes de empezar a ensamblar. Lea completamente cada uno de los pasos antes de empezar a ensamblar cada paso.
  • Page 21 Separando sus tuercas y tornillos antes de empezar reducirá el tiempo de instalación. NOTA: Separe las partes ahora para que este listo antes de empezar la instalación. IDENTIFICADOR DE TORNILLOS # DE REFERENCIA 1/4-20 x 1-1/2 Tornillo 1/4-20 X 1 1/4 Tornillo de cabeza Hexagonal de Cabeza Hexagonal (Cant.
  • Page 22 La superficie de la mesa se puede poner sobre de dos caballetes de carpintería. Aunque esto hará más fácil ensamblar la mesa, no es necesario para que pueda completar el ensamblado. Siempre utilice los cartones del empaque donde venía la mesa, para proteger la superficie de la mesa pintada. CONSEJOS DE INSTALACIÓN PRECAUCIÓN...
  • Page 23 Orificios de guía para el riel PRECAUCIÓN: SI USA UN DESTORNILLADOR ELÉCTRICO, DEBE USARLO EN POTENCIA BAJA Y TENER MUCHO CUIDADO DE NO AJUSTAR EN EXCESO YA QUE DAÑARÍA LA MESA CON LOS TORNILLOS, Y LE CAUSARÍA DAÑOS IRREPARABLES. NO SOBRE APRIETE LOS TORNILLOS! PRECAUCIÓN: CUANDO ENSAMBLE LA MESA, ES EXTREMADAMENTE IMPORTANTE QUE TODAS LAS (6) ABRAZADERAS “U”...
  • Page 24 NECESITA: #8 X 7/16” Tornillo (Cant. 20) 4. Alinie los orificios de los soportes de montaje #33 y #34 con los orificios de guía en el tablero e inserte los tornillos #20 como se muestra. Todos los orificios en los Soportes #33 y #34 deben de alinearse con los orificios en el tablero.
  • Page 25 NECESITA: #10-24 X 1/2 Tuerca (Cant. 2) ¼” Tuerca Abrazadera #10-24 X 1/2 Tornillo (Cant. 2) (Cant. 2) 1/4-20 x 2 1/4 Tornillo Rondana de (Cant. 2) Plástico (Cant. 4) Instale las patas (#2) al Soporte de Montaje (#34) con el Tornillo de Cabeza Hexagonal (#38), dos Rondanas de Plástico (#24) y la Tuerca de Seguridad (#15).
  • Page 26 NECESITA: #8-32 X 1 ¼ Tornillo (Cant. 2) Nota: Use anteojos de seguridad para el Paso 7. Nota: Rote el soporte #7 hasta que se vean los orificios a través de las ranuras de las abrazaderas #3 donde van Figura los tornillos.
  • Page 27 TORNILLOS, Y LE CAUSARÍA DAÑOS IRREPARABLES. NO SOBRE APRIETE LOS TORNILLOS! Nota: Rieles se instalan con tornillos NECESITA: #20. #8 x 1 7/16 Nota: Logo de Prince Tornillo va hacia afuera y esta Abajo de la mesa en lado del riel. (Cant. 6)
  • Page 28 NECESITA: NECESITA: Separador Rondana de 1/4-20 x 2 1/2 Tornillo de ¾” Plástico ¼” Tuerca (Cant. 1) (Cant. 2) (Cant. 2) (Cant. 3) Separador de 5/16” 1/4-20 x3 1/4 Tornillo 1/4-20 x 1 1/2 Tornillo (Cant. 2) (Cant. 2) (Cant. 1) 12.
  • Page 29 NOTA: NO GOLPEE EL CASQUILLO DIRECTAMENTE CON EL MARTILLO! COLOQUE UN PEDAZO DE MADERA SOBRE EL CASQUILLO Y GOLPEE SOBRE EL PEDAZO DE MADERA PARA INSERTAR EL CASQUILLO ADENTRO DEL SOPORTE #7. 16. Inserte el casquillo de la llanta #12 dentro del soporte en forma de U #7 hasta que el borde del casquillo toque el borde del tubo.
  • Page 30 NECESITA: Logo en la PRECAUCIÓN: parte #5 va 1/4-20 x 1 1/4” ¡POR LO MENOS SE REQUIERE DE DOS (2) hacia afuera. ADULTOS PARA MOVER LA MITAD DE LA MESA! Tornillo (Cant. 4) ¼” Tuerca (Cant. 8) Logo en la parte #5 va 1/4-20 x 1 1/2 Tornillo hacia afuera.
  • Page 31 NECESITA: PRECAUCIÓN: ¡POR LO MENOS SE REQUIERE DE DOS (2) ADULTOS PARA MOVER LA MITAD DE LA MESA! Rondana de Plástico (Cant. 2) 1/4-20 x 2” Tornillo (Cant. 2) ¼” Tuerca (Cant. 2) 22. Repita los pasos del 1 al 17 en la segunda mitad de la mesa y continue con el paso 23.
  • Page 32 Recargue esta mitad contra la pared. La Primera Mitad de la mesa que ensamblo. Figura 9 La Segunda Mitad de la mesa que ensamblo. NECESITA: ¼” Tuerca (Cant. 2) 1/4-20 x 1 1/2 Tornillo (Cant. 2) 24. Esté seguro que las patas de la primera mitad de la mesa (la mitad con la placa #5) estén abiertas.
  • Page 33 Figura 10 Detalle J NO SOBRE AJUSTE EL PASADOR DE SEGURIDAD #8. NECESITA: DEBE DE GIRAR LIBREMENTE! #10-24 Tuerca (Cant. 2) Vista de Arriba #10 Rondana (Cant. 2) Placa #5 #10-24 X 3/4 Tornillo Pasador de Seguridad #8 (Cant. 2) (el borde se extiende sobre la placa) Detalle K INSTALE LOS PASADORES DE SEGURIDAD #8 COMO SE MUESTRA ARRIBA...
  • Page 34 29. Asegure los postes de la red al centro de la mesa, ajuste los tornillos en los postes de la red, como se muestra en la Dibujo A. 30. Inserte el sostenedor de la paleta de ping pong en el poste de la red, como se muestra en el dibujo B.
  • Page 35 INSTRUCIONES PARA ABRIR Y CERRAR LA MESA ¡LEA AS INSTRUCCIONES DE MANEJO ANTES DE MOVER LA MESA! ¡NO PERMITA QUE NIÑOS ABRAN LA MESA! NO DEBEN DE PARARSE, SUBIRSE O BRINCAR SOBRE LA MESA. PUEDEN OCURRIR LESIONES GRAVES O ADVERTENCIA! MORTALES.
  • Page 36 GARANTÍA LIMITADA POR 90 DÍAS ® Esta garantía es aplicable para consumidores de la compra original de cualquier producto ESCALADE SPORTS (en adelante denominado el "Producto"). DURACIÓN DE LA GARANTÍA: Se garantiza este Producto al comprador original por un período de (90) días a partir de la fecha de compra. COBERTURA DE LA GARANTÍA: ESCALADE SPORTS le garantiza al comprador original que cualquier producto de su fabricación está...
  • Page 37 LISTA DE PARTES PARA EL MODELO T8840 Núm de Descripción Cant. Núm de Parte Ref. TABLERO 4A-5522-00 PATA 1A-7894-00 ABRAZADERA EN U -1” 2S-6879-10 TUBO CONECTOR 8S-6758-05 PLACA 2S-6422-34 TIRA DE METAL DE SEGURIDAD 2S-6428-01 TUBO DE SOPORTE EN U...
  • Page 38 *LISTA DE PARTES EN LA PAGINA ANTERIOR. 2L-4239-00...
Save PDF