1. Manuals
  2. Brands
  3. Huck Manuals
  4. Industrial Electrical
  5. POWERIG 940
  6. Instruction manual

Huck POWERIG 940 Instruction Manual

Hydraulic unit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
I
M
nstructIon
anual
M
940
odel
POWERIG
H
u
®
ydraulic
nit
Makers of Huck
, Marson
, Recoil
®
®
®
Brand Fasteners, Tools & Accessories
August 6, 2015
HK496

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the POWERIG 940 and is the answer not in the manual?

Questions and answers

Summary of Contents for Huck POWERIG 940

  • Page 1 POWERIG ® ydraulic Makers of Huck , Marson , Recoil ® ® ® Brand Fasteners, Tools & Accessories August 6, 2015 HK496...
  • Page 2 940 series Powerig® Alcoa Fastening Systems & Rings (HK496) NOTICE This manual applies to 940 serial number 3927 and above. For any other serial numbers, please contact a Huck customer service representative.

  • Page 3: Table Of Contents

    940 series Powerig® Alcoa Fastening Systems & Rings (HK496) ontents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description .

  • Page 4: Safety

    19. Check clearance between trigger and work piece to ensure there Bold, Italic type and underlining: emphasizes a specific instruction. is no pinch point when tool is activated. Remote triggers are 1. A half hour long hands-on training session with qualified available for hydraulic tooling if pinch point is unavoidable. personnel is recommended before using Huck equipment. 20. Unsuitable postures may not allow counteracting of normal 2. Huck equipment must be maintained in a safe working expected movement of tool. condition at all times. Tools and hoses should be inspected at the beginning of each shift/day for damage or wear. Any 21. Do not abuse tool by dropping or using it as a hammer. Never repair should be done by a qualified repairman trained on Huck use hydraulic or air lines as a handle or to bend or pry the tool.

  • Page 5: Description

    Unil at the end of an installation cycle. Pressures are adjust- Powerig is rated at 115V, 50/60Hertz, 25A. able to match Huck equipment being used. See applicable tool instruction manual for pressure settings for other Huck An electrical enclosure contains a motor contactor, trans- installation equipment.

  • Page 6: Principle Of Operation

    Single Phase Electrical Schematic TRIGGER Diagram for ® 940 Powerig ® REV B HUCK INTL. INC. 590303 U.S. Registration reparatIon for Service Before Use Introduction of foreign material into Hydraulic Unit will Fill the reservoir with hydraulic fluid, approximately result in poor performance and down time for repair.

  • Page 7: Checking And Adjusting Pressures

    P on the be understood before checking pressures. tool. Connect hydraulic hoses from a HUCK hydraulic tool 2) Hose from RETURN PRESSURE on the control to the Powerig Hydraulic Unit. panel runs to the port stamped with letter R on the...

  • Page 8: Maintenance

    Fiske Brothers Refining Co. and is avail- WIRING able in most localities. A handy tube of LUBRIPLATE See Figure 6 for wiring diagram and TABLE 1 for wire 130AA is available from Huck as part number 502723. list. INTERNAL ADJUSTMENT OF PRESSURE SWITCH PREVENTIVE MAINTENANCE 1.

  • Page 9: Assembly Reference Drawings

    940 series Powerig® Alcoa Fastening Systems & Rings (HK496) 111345 p otor alVe sseMbly Igure 107317 Filler/Breather 115753 Pressure Switch Assembly 111415 Motor Brush 500071 Screw (10) 106397 External 112625 Pilot Relief Valve Valve Adapter Plate Note: This assembly is purchased complete.
  • Page 10 940 series Powerig® Alcoa Fastening Systems & Rings (HK496) 123490 e leCtrICal nClosure sseMbly Igure...
  • Page 11 940 series Powerig® Alcoa Fastening Systems & Rings (HK496) leCtrICal CheMatIC anD IrIng IagraM Igure...

  • Page 12: Powerig Options And Accessories

    940 series Powerig® Alcoa Fastening Systems & Rings (HK496) & a ptIons CCessorIes OPTIONS 940T-1 (Special Version of 940) Rig Transport Dolly 129703 The 940T-1 is part of Huck’s revised aftermarket Truck Kits, Heavy duty steel dolly for easy movement of powerig which contain different pressure installation tools. This throughout the work area. hydraulic unit will be shipped from the factory with output pressures set as follows: Motor 111346 PULL: 5700-5800 psi RETURN: 4400-4600 psi Motor and Pump Assembly 111345...
  • Page 13 Huck shall not be liable for any loss or damage result- THERE ARE NO WARRANTIES WHICH ing from delays or non-fulfillment of orders owing to...
  • Page 14 International. Huck provides technical assistance acknowledgments, and/or purchase orders. It For the Long Haul ™ regarding the use and application of Huck fasten- is recommended that the user secure specific, ers and tooling. up-to-date data and information regarding each application and/or use of such products.

This manual is also suitable for:

Powerig 940

Table of Contents