Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ACTi A92
Summary of Contents for ACTi A92
- Page 1 Outdoor Mini Dome Hardware Manual Ver. 2017/09/08...
-
Page 2: Table Of Contents
How to Remove the Memory Card ..........18 Accessing the Camera Configure the IP Addresses ............19 Using DHCP Server to Assign IP Addresses ........ 19 Using the Default Camera IP Address .......... 21 Access the Camera ................. 23 www.acti.com... -
Page 3: Precautions
Every reasonable care has been taken during the writing of this manual. Please inform your local office if you find any inaccuracies or omissions. ACTi will not be held responsible for any typographical or technical errors and reserves the right to make changes to the product and manuals without prior notice. - Page 4 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 55024. In a domestic environment, this product may cause radio interference in which cause the user may be required to take adequate measures. www.acti.com...
-
Page 5: Safety Instructions
Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine if the product is in proper operating condition. www.acti.com... -
Page 6: Introduction
Hardware Manual Introduction List of Models This hardware manual contains the following models: 3MP Outdoor Mini Dome with D/N, Adaptive IR, Advanced WDR, SLLS, Fixed lens www.acti.com... -
Page 7: Package Contents
When the camera is taken out from the box, the lens cover is covered by a thin film. DO NOT remove this film. It is used to protect the lens cover from scratches or fingerprint marks which may happen during installation. Remove this film only after the camera is securely installed and all connections are complete. www.acti.com... -
Page 8: Physical Description
1. While the camera power is disconnected, press and hold the Reset Button then power up the camera. 2. The Green LED starts to blink, continue holding down the Reset Button until the Green LED goes off and the Yellow LED lights on. www.acti.com... -
Page 9: Mounting Options
NOTE: For more information about the mounting solutions and accessories, please check the Mounting Accessory Selector in our website (http://www.acti.com/mountingselector). The above mounting accessories are not included in the package. Contact your sales agents to purchase. www.acti.com... -
Page 10: Installation Procedures
How to Move the Camera Cable From Side to Bottom on page 15 for instructions. Otherwise, skip this step. 3. Loosen the four (4) screws using the bundled hexagon wrench. 4. Lift to remove the dome cover. www.acti.com... -
Page 11: Step 2: Install The Camera
See How to Insert the Memory Card on page 18 for more information. 2. Install the camera to the surface using the four (4) bundled screws. NOTE: Please make sure the screws are flat on the plate. www.acti.com... -
Page 12: Step 3: Connect To Network
NOTE: When installing the camera outdoors, make sure to waterproof the cable connection. Step 4: Access the Camera Live View Accessing the Camera on page 19 for more information on how to access the Live View of the camera. www.acti.com... -
Page 13: Step 5: Adjust The Viewing Angle
Adjust the camera lens orientation and tilt, as needed. 1. Loosen the tilt adjustment screw, and then tilt the lens module. 2. Rotate the lens module to change the viewing orientation. 3. Tighten the tilt adjustment screw to fix the lens position. www.acti.com... -
Page 14: Step 6: Close The Dome Cover
Hardware Manual Step 6: Close the Dome Cover 1. Tighten the four (4) screws using the supplied hexagon wrench to attach the dome cover. www.acti.com... -
Page 15: Other Installation And Accessories
3. Remove the cables through the side cable hole. The Ethernet cable has a wider wafer head, which you may need to pull sideways to fit the cable hole. NOTE: Be careful not to damage the wafer and cables, this will void the warranty. www.acti.com... - Page 16 Make sure the gland is secured tightly to ensure waterproof. 6. Remove the three (3) screws, and slightly lift the camera module enough to connect the power cable wafer (2-wire) on its connector. NOTE: Do not abruptly lift the camera module, cables are connected underneath. www.acti.com...
- Page 17 Hardware Manual 7. Connect the wafer heads to its corresponding connectors. 8. Attach the camera module back. www.acti.com...
-
Page 18: How To Install / Remove The Memory Card
In case there is a need to remove the card, make sure to access the camera Web Configurator to safely “unmount” the card first (see the camera Firmware User’s Manual for more information). Once unmounted from the firmware, pull the card out of the slot. www.acti.com... -
Page 19: Accessing The Camera
Windows system – just by pressing the “Network” icon, all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our cameras. In the example below, we successfully found the camera that we had just connected to the network. www.acti.com... - Page 20 The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility With just one click, you can launch the IP Utility and there will be an instant report as follows: You can quickly see the camera model in the list. Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already.
-
Page 21: Using The Default Camera Ip Address
PC has to be configured to match the network segment of the camera. Manually adjust the IP address of the PC: In the following example, based on Windows 7, we will configure the IP address to 192.168.0.99 and set Subnet Mask to 255.255.255.0 by using the steps below: www.acti.com... - Page 22 In such case, please plug in only one camera at a time, and change its IP address by using the Web browser before plugging in the next one. This way, the Web browser will not be confused about two devices having the same IP address at the same time. www.acti.com...
-
Page 23: Access The Camera
The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera. Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 www.acti.com... - Page 24 HTTP port of the camera is 80, which can be omitted from the address for convenience. Before logging in, you need to know the factory default Account and Password of the camera. Account: Admin Password: 123456 www.acti.com...
- Page 25 Copyright © 2017, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.com...
Need help?
Do you have a question about the A92 and is the answer not in the manual?
Questions and answers