Related Manuals for Aviosys IP Power 9258S
Summary of Contents for Aviosys IP Power 9258S
- Page 1 IP POWER 9258 USER MANUAL IP Power 9258S / 9258T 9258S+Ping / 9258T + Ping USER MANUAL IP POWER 9258S/T , 9258S/T+Ping Firmware Version: V5.12 AUGUST , 2018...
- Page 2 IP POWER 9258 USER MANUAL Warning: Any changes to this equipment without permission may cause damages to your equipment! This equipment has been proved by CE & FCC to can be prevented from the influence of harmful electronic jamming in normal business use condition. IMPORTANT NOTICE 1.
-
Page 3: Table Of Contents
IP POWER 9258 USER MANUAL Table of Content 1. INTRODUCTION ............................3 ................................ 3 EATURE ............................... 3 PECIFICATION SPECIFICATION ..........................4 ............................ 4 ACKAGE CONTENTS ......................4 INIMUM YSTEM EQUIREMENTS 3. INTERFACE DESCRIPTION ......................... 5 HARDWARE & SOFTWARE INSTALLATION ................6 ........................... -
Page 4: Introduction
IP POWER 9258 USER MANUAL 1. Introduction IP POWER 9258 is a web controller which can be easily used in the industry field. With the remote network control technology, user can control or query the power supply of equipment. User can do this in any computer connected to the internet or local area network, there is no special program needed, also there is no need to open the external case of the computer. -
Page 5: Specification
NOTICES: 1. IP Power 9258S: for 220-250V, please use power (IN) wire at 10A current. Max output current: (total) 10A. Max (individual) 6A. 2. IP Power 9258T: for 100-120V, please use power (IN) wire at 15A current. -
Page 6: Interface Description
IP POWER 9258 USER MANUAL 3. Interface Description IP Power 9258 Front interface shown below: From left to the right 1. RESET: self-protect AC reset button. IP Power 9258 can cut off the power supply of outlets automatically if there is a shortcut or current overload. After user having solved the problem, push the reset button, the AC power supply will become normal. -
Page 7: Hardware & Software Installation
Check the voltage of the power supply to make sure it is AC 110-240 volt ◼ Please confirm the specification of your power cable. ⚫ IP Power 9258S: for 220-250V, please use the 10A power cable. ⚫ IP Power 9258T: for 100-120V, please use the 15A power cable. Hardware installation a) Connect the 9258 to HUB through network wire. -
Page 8: Software Installation
IP POWER 9258 USER MANUAL Software installation Please follow the steps below to install the software. Insert the Installation CD in the package and windows will auto-run. If not please browse for the Autorun.html file in CD. Click 9258S & 9258T in the IP POWER section of the installation CD 3.In stall IP Family to your desktop or any other place of your choosing 4. - Page 9 IP POWER 9258 USER MANUAL IPEDIT will search and display all IP Products 9XXX series under the same local Ethernet. The default name for the IP Power 9258 is “IP9258” 1. Double click and highlight your IP Power 9258 device. The default device name and IP/Network settings will all be displayed on the right hand side of IPEdit.
- Page 10 IP POWER 9258 USER MANUAL 2.) * The default IP address of the 9258 is 192.168.1.100. If you cannot get into the webpage of the 9258, please make sure to set subnet of the IP Power 9258 to match with your PC Subnet Mask.
-
Page 11: Hardware Control & Settings
IP POWER 9258 USER MANUAL 6. Hardware Control & Settings * This function teaches you how to use the hardware control the power on/off of the devices NOTE: This function is solely used for manually selecting which ports you need to be on or off. It was designed so that you can still have the ability to turn on or off certain ports in the case you do not have Ethernet connection. -
Page 12: Control & Settings
IP POWER 9258 USER MANUAL 7. Control & Settings To login to the IP Power 9258 device through web browser like google chrome / Internet Explorer, type in the IP Address of your device to log in . This will take you to the IP 9258 Login page. -
Page 13: Device Name & Time
IP POWER 9258 USER MANUAL Device Name & Time A. Device Name : This section show the device name & Time. Device name can be change in System → Setup → Device Name . Please change the name in English only and do not use symbol like !@#$%^&*()_+ and so on . -
Page 14: Power
IP POWER 9258 USER MANUAL B. Time : In this section, it shows Time at Year – Month – Date Hours : Minutes : Seconds . User can setup the time manually or press “ local time “ bottom to get the PC `s time . Or use the time of Network Time Protocol (NTP) Server . - Page 15 IP POWER 9258 USER MANUAL A. Control User can do the following 3 basic operation in this page : A-1 . Manual control each port ON or OFF directly by pressing the power sign. A-2. Power Cycle & Group Setting : This section allow user to setup the output Reset action and Group control .
- Page 16 IP POWER 9258 USER MANUAL Support parameter of operate schedule: ⚫ Disable ⚫ Just Once ⚫ Every day ⚫ Work Day: From Monday to Friday. ⚫ Weekend: Saturdays and Sundays ⚫ Monday & Thursday ⚫ Tuesday & Friday ⚫ Wednesday & Saturday C.
- Page 17 IP POWER 9258 USER MANUAL - Power : to enable / disable the ping function - IP /Host : Enter the IP Address or Host name of the device that you are trying to ping - Failure Times : The times of Unsuccessful Ping responses. - Before Action : After “Failure Times”...
-
Page 18: System Setting
IP POWER 9258 USER MANUAL System Setting There are 6 sections : Setup , DDNS , Email , Password , Network Wakeup & IP Service . A. Setup – System Configuration Click on the Setup link located on the left hand column. In this page the user will be able to manually enter the IP Address, Subnet Mask, Default Gateway, DNS, SNMP , TELNET , DHCP , Beeper, Http Command , Switch Interval ( Delay Switch ) , Device name and Version. - Page 19 IP POWER 9258 USER MANUAL IP address Settings: Ethernet (LAN) and Internet - IP Address: please type in the IP address provided by your ISP. If IP Power 9258 is working with a Router, please refer to the network settings of the Router. ⚫...
- Page 20 IP POWER 9258 USER MANUAL B. DDNS When the user connects to the Internet through ADSL (PPPOE Service), the IP address that you receive from ISP is usually a dynamic IP Address. Therefore when someone wants to visit your device they are usually not able to because the IP Address is dynamic and it will keep changing. By using DDNS this problem is solved.
- Page 21 IP POWER 9258 USER MANUAL C. EMAIL SETUP: When you finished the e-mail setup , you can set to let IP Power 9258 send its IP address automatically. To send out mail successfully , please do set the DNS correctly . You can check with your ISP for correct DNS information.
- Page 22 IP POWER 9258 USER MANUAL Receiver: no longer than 50 English letters. Please use blank space to separate two receiver’s e-mail address. After you have finished this setting, you will receive the email to inform you the IP address of the IP Power 9258 every time you enter the webpage. Subject: the subject of the mail to be no more than 50 English letters.
- Page 23 IP POWER 9258 USER MANUAL F. IP Service IP Server gives the user the ability to easily search for the name of the device other than searching for a long IP number. This flexibility allows the user to easily just remember the name of their device so they can access it with ease.
-
Page 24: Setting Of Software Shut Down Controlled Pc/ Server
IP POWER 9258 USER MANUAL Setting of software shut down controlled PC/ Server 9258 can be used to safely turn off the PC/Server through Network. With this feature you can remotely shutdown any PC/ Server which that is connected to the IP Power 9258 through normal Windows shut down procedure. - Page 25 IP POWER 9258 USER MANUAL * IP9258 Address: Please type in the IP address of the 9258. * Http Port: Fill the port of 9258, default value is 80, if amend the port in 9258 please correct. * UserName: admin * Password: 12345678 (password can amend in web page) * Power Number: Please enter the power number in the 9258 that you want to control (If many PC/Server use same power extended line, the extended line connect to channel...
-
Page 26: Snmp - Mib Tree
IP POWER 9258 USER MANUAL 8. SNMP – MIB Tree 9258 support SNMP V1 and V2 , user can use snmp program to get the status of each port in 9258. We also supply standard MIB tree . Please contact with your distributor for the information. - 25 - VER. -
Page 27: Http Command & Telnet
IP POWER 9258 USER MANUAL 9. HTTP Command & TELNET CGI / HTTP Commands Http commands allow you to control the device with commands. The basic commands are provided below. There are two ways to input http commands with authorization required * Password in http: for Browser IE 7.0 or below http://login:password@ipaddrss:port/set.cmd?cmd=command * Password not in http: for Browser IE 7.0 and higher... -
Page 28: C.) Power Delay
IP POWER 9258 USER MANUAL 2. Read Port http://192.168.1.3/set.cmd?cmd=getpower c.) Power Delay The Power delay command allows you to delay the set power command. Command format : http://ip:port/set.cmd?cmd= setpower+p6x=?+p6xn=?+t6x=aa x means output number : 1 or 2 or 3 or 4 ? means on or off : 1 = on , 0 = off p6xn means 2nd action of output x... -
Page 29: E.) Setup Schedule
IP POWER 9258 USER MANUAL e.) Setup Schedule Command format: One command to set one schedule status. http://ip:port/set.cmd?user=admin+pass=12345678+cmd=setschedule+power=xx +yy=2006+mm=02+dd=16+hh=06+mn=02+ss=16+param=128+onoff=1 Parameter definition : xx means Schedule item number : 1a, 1b, 2a, 2b, 3a, 3b, 4a, 4b yy=2006 ( Year 2006) mm=02 ( Month as February ) dd=16 ( Date as 16 ) -
Page 30: Telnet
IP POWER 9258 USER MANUAL TELNET The 9258 supports telnet protocol and can be controlled in a telnet enabled environment. To Login to the 9258 in telnet 1.) Make sure to go to command prompt and type in Telnet and the IP Address of your 9258 device. - Page 31 IP POWER 9258 USER MANUAL Set power: The set power command allows the device to turn on and turn off ports on the device. To set power on the device type For example : The default status of each port are all OFF. Telnet Command Port 4 Port 3...
-
Page 32: Faq
IP POWER 9258 USER MANUAL 10. FAQ Q1: I forgot the password and can not enter the administration page now, what can I do? A1: Use username "super user" when log in webpage and then click "OK " turn power off for few second and then turn on ON .
Need help?
Do you have a question about the IP Power 9258S and is the answer not in the manual?
Questions and answers