Related Manuals for KUHN HAYBOB 300
Summary of Contents for KUHN HAYBOB 300
- Page 1 HAYBOB 300 O p e r a t i o n m a n u a l Issue 5/2009 Date of printing 6.2009 Language Ex machine no. (PIN) VGTH222624 Serial number (PSN) 67TH01 Reference No. ZNA016EN...
- Page 2 5667 KP Geldrop The Netherlands Phone +31 40 2893300 KUHN-GELDROP BV retains all copyrights and rights of usage. The contents of this operating manual are subject to change without notice. All rights reserved. The right to technical revision is reserved.
-
Page 3: Table Of Contents
Table of contents Table of contents Preface............. 4 Used terms and symbols ....... 5 General Destination and intended use ....... 6 General Safety and reliability ........7 Safety instructions 3-point rotary hay making machines Safety and reliability ........12 Tractor loads Pre-operation .......... -
Page 4: Preface
Preface The range of your machinery has now been improved which Preface incorporates the latest developments in hay making. It is a first class engineering product backed by a widespread distributor/dealer organisation to give you an efficient after sales service. This machine shall be exclusively used for the normal agricultural work as described in section "Destination and intended use"... -
Page 5: Used Terms And Symbols
Used terms and symbols Used terms and symbols Specifications are subject to change without previous notice. G e n e r a l Directional indications such as 'right', 'left', 'front' and 'rear', etc. are to be interpreted when facing in direction of travel. Parts are numbered from left to right. -
Page 6: Destination And Intended Use
T e c h n i c a l s p e c i f i c a t i o n s Machine type HAYBOB 300 Machine code Working width: 300 cm... -
Page 7: Safety And Reliability
Safety and reliability Avoid accidents! Don't learn safety the hard way! Stay alert! Safety and reliability Think SAFETY! Work SAFELY! Prior to operating the machine read and observe this operation manual and all safety instructions and decals Everyone must be given operating instructions before starting to operate the equipment. - Page 8 Safety and reliability the corresponding position! • Always fit front weights to the fixing points provided for that purpose. • Adhere to maximum permissible axle loads, total weights and transport dimensions! • Install and check transport equipment, e.g. lighting, warning devices, guards! •...
- Page 9 Safety and reliability • Do not modify the equipment in any way. Unauthorised modifications may impair the function and/or safety and could affect the life of the equipment! • Repair damages prior to next operation. • Only use universal joint drive shafts complying with the D r i v e t h r o u g h u n i v e r s a l specification of the machine manufacturer for that specific use! j o i n t d r i v e s h a f t s...
- Page 10 Safety and reliability • After removal of PTO drive shaft place protective cover/cap over PTO! • When working on the wheels make sure that the machine has been W h e e l s a n d t y r e s placed on the ground safely (jack stand) and that it is secured by chocks against unintentional rolling! •...
- Page 11 Safety and reliability In order to ensure safety all persons working at and/or with this L i a b i l i t y a n d w a r r a n t y machine must read and understand this operation manual. Furthermore this machine shall always be used, handled and stored in accordance with the design and construction destination (intended use) which also means:...
-
Page 12: Safety And Reliability
Safety and reliability Safety and reliability Attention: T r a c t o r l o a d s Obey the maximum permissible mass, permissible axle loads and permissible tyre loads. Attaching machines to the front or to the rear 3-point linkage may never result in: •... - Page 13 Safety and reliability The actual front axle load can be determined by: A c t u a l f r o n t a x l e l o a d • weighing. • calculation: D x (F + G + H) D x (F + G +H) = ..
- Page 14 Safety and reliability The actual tyre load can be found by dividing the corresponding actual A c t u a l t y r e l o a d axle load by 2. The actual tyre load may never exceed the maximum permissible tyre load.
-
Page 15: Pre-Operation
Pre-operation Pre-operation Since the hitch brackets are reversible, the hitch frame is suitable for A t t a c h m e n t t o t h e both cat. I and II. t r a c t o r - Cat. -
Page 16: Operation
Operation Operation To enable the machine to follow ground contours correctly, the G e n e r a l i n s t r u c t i o n s hydraulic lift lever should be in float position during work, so that the f o r u s e lift arms can move freely up and down. - Page 17 Operation > Then lower machine completely and drive a little forward, until the centre slot at front of hitch frame appears clearly visible (arrow, fig.). In this position the forward side of the rotors is nearest the ground. > Now operate machine at full working speed (350-540 rpm at the pto) and adjust top link, so that the tine tips are just touching the stubble in front of the rotors.
- Page 18 Operation A d j u s t m e n t f o r r a k i n g > Lower machine and start a rh turn. > Then pull cord (4) to disengage lever (2) from bracket pin (3). >...
- Page 19 Operation > Set deflectors as required using stays (8). Always make certain that the distance between the deflectors is large enough, especially in a heavy crop to prevent material from being pulled out of the swath. When you place the deflectors as shown in fig. the swaths are laid down close together in the first operation.
-
Page 20: Maintenance
Special attention should be paid to those holding the tines and bolts securing the rotors, located under the top of the rotors. Recheck regularly. The HAYBOB 300 has 4 different tines T i n e s •... - Page 21 Maintenance Attention L u b r i c a t i o n Always use a good and adhesive multi-purpose grease for lubrication of both machine and PTO drive shaft! The following points need the attention: • Machine • PTO drive shaft Attention Ensure profiles tubes of pto drive shafts are well greased at all times! Check a new or repaired machine and/or drive shaft prior to first run...
-
Page 22: Torque Values For International Metric Thread Joints
Maintenance All bolted joints on this machine must be torqued in accordance with T o r q u e v a l u e s f o r the values given in this table below unless indicated otherwise (e.g. in i n t e r n a t i o n a l m e t r i c Parts List or Installation Instruction, etc.) On this machine 8.8 is both standard and minimum quality used. - Page 23 Maintenance Tensile strength Material quality acc. to DIN ISO 898 10.9 12.9 up to and incl. M16 over M16 1040 1220 N/mm lbf/sq.in. 117,222 120,414 150,880 176,994...
-
Page 24: Conversion Table For Units Of Measurement
Maintenance C o n v e r s i o n t a b l e f o r u n i t s o f m e a s u r e m e n t Length 1000 mm 39 3/8 in 3.2809 ft 1 mm... -
Page 25: Maintenance
Maintenance Maintenance Torque 1 Nm 0.102 kg(f)m 1 Ws 0.738 ft-lb(f) 1 ft-lb(f) 1.356 Nm 12 in-lb(f) 1 in-lb(f) 0.113 Nm Power 1 kW 1000 W 0.738 ft-lb(f)/s 1.359 pk 1.359hp 1 pk 1 PS 1 cv 1 cf 0.73575 kW 1 hp 0.73575 kW 1 Btu/h... -
Page 26: Optional Equipment
Optional equipment Parts listed below can be standard equipment in your area: contact Optional equipment your dealer. Install in accordance with the assembly/installation instructions of the respective option. Install in accordance with the assembly/installation instructions of the respective option. For spare parts see IPL. Your order for spare parts should contain the following information: I n s t r u c t i o n s f o r o r d e r i n g •... -
Page 27: Ec Certificate Of Conformity
NL-5667KP Geldrop The Netherlands declare in sole responsibility, that the product Rotary Hay Making Machine HAYBOB 300 and accessories to which this certificate relates, conforms to the basic safety and health requirements of the Directives 89/392/EEC (amended with 91/ 368/EEC, 93/44/EEC and 93/68/EEC) and 98/37/EC. -
Page 28: Index
Index Index Adjustments for raking Used terms and symbols Adjustments for spreading and tedding Attachment to the tractor Wheels and tyres Safety and reliability Destination and intended use General Technical specifications Maintenance Conversion table for units of measurements General Lubrication Tines Torque values for international metric thread joints...
Need help?
Do you have a question about the HAYBOB 300 and is the answer not in the manual?
Questions and answers